Laser speckle noise caused by coherence between lasers greatly influences the produced image. In order to suppress the effect of laser speckles on images, in this paper we set up a combination of a laser-structured light module and an infrared camera to acquire laser images, and propose an improved weighted non-local mean (IW-NLM) filtering method that adopts an SSI-based adaptive h-solving method to select the optimal h in the weight function. The analysis shows that the algorithm not only denoises the laser image but also smooths pixel jumps in the image, while preserving the image details. The experimental results show that compared with the original laser image, the equivalent number of looks (ENL) index of the IW-NLM filtered image improved by 0.80%. The speckle suppression index (SSI) of local images dropped from 4.69 to 2.55%. Compared with non-local mean filtering algorithms, the algorithm proposed in this paper is an improvement and provides more accurate data support for subsequent image processing analysis.

The utilization rate of ink liquid in the chamber is critical for the thermal bubble inkjet head. The difficult problem faced by the thermal bubble inkjet printing is how to maximize the use of ink in the chamber and increase the printing frequency. In this paper, by adding a flow restrictor and two narrow channels into the chamber, the H-shape flow-limiting structure is formed. At 1.8 μs, the speed of bubble expansion reaches the maximum, and after passing through the narrow channel, the maximum reverse flow rate of ink decreased by 25%. When the vapor bubble disappeared, the ink fills the nozzle slowly. At 20 μs, after passing through the narrow channel, the maximum flow rate of the ink increases by 39%. The inkjet printing frequency is 40 kHz, and the volume of the ink droplet is about 13.1 pL. The structure improves the frequency of thermal bubble inkjet printing and can maximize the use of liquid in the chamber, providing a reference for cell printing, 3D printing, bioprinting, and other fields.

This paper presents a new numerical approach for the full extraction of the coupling-of-modes (COM) parameters by stationary and eigenfrequency analyses in the finite element method (FEM). This is a fast method extracting from the results of static analysis and eigenfrequency analysis. It avoids the long calculation time of admittance frequency response analysis, which is commonly used in extracting COM parameters. In addition to the usual COM parameters (velocity, reflection coefficient, transduction coefficient and capacitance), the phases of reflection and transduction coefficient can be also extracted with this method. The proposed method was applied to different cutting types LiNbO₃ with different types of thicknesses in a varying interdigital transducer (IDT). These examples show that our approach has great potential in extracting all the COM parameters of the Rayleigh SAW for all kinds of IDT structures. Therefore, it is a fast, accurate, general and full extraction approach of COM parameters.

The current structured light projector is generally large in size. In order to realize a compact and small-sized module, this paper proposes to substitute the conventional refractive lenses with the most popular meta-lenses to achieve compactness. This paper focuses on the analysis of the metalens performance requirements, design methods and simulation results. Varying diameters of these nano-pillar structures are used to adjust the phase of the electromagnetic wave to realize flat lens. Two types of all-dielectric meta-lenses are designed for using in ultra-compact structured light projector. Parameters of two meta-lenses at wavelength of 850nm are depicted as follows: the focal length f=500um, aperture size D=100um, numerical aperture NA=0.1, FWHM=0.323λ and the focal length is f=50um, aperture size is D=100um, numerical aperture is about NA=0.7, FWHM=0.598λ, respectively. At last, simulation results show that this solution can achieve an ultra-compact structured light projector, which is 77% smaller than the traditional technology.

Efficient printing frequency is critical for thermal bubble inkjet printing, while the difficulty lies in the structural design and material selection of the heating resistors. In this paper, a TaN film was used as the main material of the heating resistors, and two TaN films were placed in parallel to form the chopsticks-shaped structure. The heating time was divided into two sections, in which 0–0.1 μs was the preheating and 1.2–1.8 μs was the primary heating. At 1.8 μs, the maximum temperature of the Si₃N₄ film could reach about 1100 °C. At the same time, the SiO₂ film was added between the TaN film and Si₃N₄ film as a buffer layer, which effectively avoided the rupture of the Si₃N₄ film due to excessive thermal stress. Inside the inkjet print head, the maximum temperature of the chamber reached about 680 °C at 2.5 μs. Due to the high power of the heating resistors, the working time was greatly reduced and the frequency of the inkjet printing was effectively increased. At the interface between the back of the chip and the cartridge, the SiO₂ film was used to connect to ensure a timely ink supply. Under the condition of 12 V at 40 kHz, the inkjet chip could print efficiently with 10 nozzles at the same time. The inkjet chip proposed in this paper is not limited to only office printing, but also provides a new reference for 3D printing, cell printing, and vegetable and fruit printing.

It is crucial to improve printing frequency and ink droplet quality in thermal inkjet printing. This paper proposed a hemispherical chamber, and we used the CFD (computational fluid dynamics model) to simulate the inkjet process. During the whole simulation process, we first researched the hemispherical chamber’s inkjet state equipped with straight, conical shrinkage, and conical diffusion nozzles. Based on the broken time and volume of the liquid column, the nozzle geometry of the hemispherical chamber was determined to be a conical shrinkage nozzle with a specific size of 15 µm in height and 15 µm in diameter at the top, and 20 µm in diameter at the bottom. Next, we researched the inkjet performance of the square chamber, the round chamber, and the trapezoidal chamber. The round chamber showed the best inkjet performance using 1.8 µs as the driving time and 10 MPa as the maximum bubble pressure. After that, we compared the existing thermal inkjet printing heads. The results showed that the hemispherical chamber inkjet head had the best performance, achieving 30 KHz high-frequency printing and having the most significant volume ratio of droplet to the chamber, reaching 14.9%. As opposed to the current 15 KHz printing frequency of the thermal inkjet heads, the hemispherical chamber inkjet head has higher inkjet performance, and the volume ratio between the droplet and the chamber meets the range standard of 10–15%. The hemispherical chamber structure can be applied to thermal inkjet printing, office printing, 3D printing, and bio-printing.