Nanocomposite materials have seen increased adoption in a wide range of applications, with toxic gas detection, such as carbon monoxide (CO), being of particular interest for this review. Such sensors are usually characterized by the presence of CO absorption sites in their structures, with the Langmuir reaction model offering a good description of the reaction mechanism involved in capturing the gas. Among the reviewed sensors, those that combined polymers with carbonaceous materials showed improvements in their analytical parameters such as increased sensitivities, wider dynamic ranges, and faster response times. Moreover, it was observed that the CO reaction mechanism can differ when measured in mixtures with other gases as opposed to when it is detected in isolation, which leads to lower sensitivities to the target gas. To better understand such changes, we offer a complete description of carbon nanostructure-based chemosensors for the detection of CO from the sensing mechanism of each material to the water solution strategies for the composite nanomaterials and the choice of morphology for enhancing a layers’ conductivity. Then, a series of state-of-the-art resistive chemosensors that make use of nanocomposite materials is analyzed, with performance being assessed based on their detection range and sensitivity.

Developing a sensing layer with high electroactive properties is an important aspect for proper functionality of a wearable sensor. The polymeric nanocomposite material obtained by a simple electropolymerization on gold interdigitated electrodes (IDEs) can be optimized to have suitable conductive properties to be used with direct current (DC) measurements. A new layer based on polyaniline:poly(4-styrenesulfonate) (PANI:PSS)/single-walled carbon nanotubes (SWCNT)/ferrocene (Fc) was electrosynthesized and deposed on interdigital transducers (IDT) and was characterized in detail using electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV), scanning electron microscopy (SEM), Raman spectroscopy, X-ray photoemission spectroscopy (XPS), and X-ray diffraction (XRD). The sensor characteristics of the material towards carbon monoxide (CO) in the concentration range of 10–300 ppm were examined, showing a minimal relative humidity interference of only 1% and an increase of sensitivity with the increase of CO concentration. Humidity interference could be controlled by the number of CV cycles when a compact layer was formed and the addition of Fc played an important role in the decrease of humidity. The results for CO detection can be substantially improved by optimizing the number of deposition cycles and enhancing the Fc concentration. The material was developed for selective detection of CO in real environmental conditions and shows good potential for use in a wearable sensor.

In this manuscript an improved sorbent based on modified exfoliated carbon nanoplatelets, applied in the removal of ammonium from aqueous samples, is presented. This sorbent showed better efficiency in comparison with the previous one obtained in our group for ammonium removal, the values of the maximum sorption capacity being improved from 10 to 12.04 mg/g. In terms of kinetics and sorption characteristic parameters, their values were also improved. Based on these results, a sorption mechanism was proposed, taking into account ion-exchange and chemisorption processes at the surface of the oxidized exfoliated carbon nanoplatelets. Future applications for simultaneous removal of other positive charged contaminants from natural waters might be possible.

In the present investigations, the density, refractive index and speed of sound for pure organic solvents and binary liquid mixtures of 3,4,4′-Trichlorodiphenylurea between (293.15 and 323.15) K temperatures have been measured up to the solubility limit. From these experimental results, the acoustic impedance, the isentropic compressibility coefficient, the space-filling factor, the specific refraction, the relaxation strength, the intermolecular free length, the surface tension, the solubility and the solvation number of triclocarban in six organic solvents, namely ethyl alcohol, n-Propyl alcohol, n-Butyl alcohol, Tetrahydrofuran, N,N-Dimethylformamide and N,N-Dimethylacetamide have been computed. The studied acoustic and optical parameters and surface tension behavior versus temperature in pure solvents and binary mixtures were useful in understanding the nature and the extent of interaction between the solute and solvent molecules. The results also show the presence of higher degree of interaction between triclocarban and nitrogen-containing solvents in comparison with other solvents. The distribution of triclocarban in water/organic solvent mixtures is frequently encountered in wastewater treatment plants.

In this study, the possibility of ²²²Rn removal through the deferrization/demanganization applied for water treatment was considered, assuming a sorption process. This study demonstrates the possible removal of dissolved radon from groundwater using manganese oxide sand (MnO₂) employed in conventional water treatment systems. Four groundwater samples with varying chemical compositions were treated, and the simultaneous removal of ²²²Rn, Mn²⁺, Fe²⁺, NH₄⁺, and NO₃⁻ was evaluated. Radon activity was quantified using a Lucas scintillation cell coupled with a Pylon AB-5 system, while inorganic ions were analyzed by ion chromatography. Structural characterization of MnO₂ sand by XRD, SEM–EDS, and FTIR confirmed a heterogeneous oxide surface favorable for adsorption. The treatment achieved average removal efficiencies of 95% for ²²²Rn, 79% for Mn²⁺, 87% for Fe²⁺, 85% for NH₄⁺, and 73% for NO₃⁻. Equilibrium adsorption capacities increased with initial contaminant concentrations, indicating a multi-species uptake. Importantly, radon removal was largely independent of coexisting ions. These results reveal the benefit of MnO₂-based water treatment, offering an effective solution for simultaneous radon and inorganic contaminant mitigation.

In this study, the chemical distribution of triclocarban (TCC), in natural aqueous systems, between water and sediment, with different chemical compositions of the aqueous phase and different percentages of organic carbon (OC%) in the sediments is presented. The influences of the temperature, of the composition of the aqueous matrices of natural waters and (OC%) in the sediment over the solubility of triclocarban, and its distribution coefficient K_d values were studied. log K_D at 25 °C varied between 1.94 and 3.27 for a sediment with 5.50% OC and between 3.95 and 5.93% for a sediment with 6.75% OC, in the studied aqueous systems, with different concentrations of OC in the sediment.