Aleksandr Umanskii

Dr. Aleksandr Umanskii

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 November 2019 in Journal of Physics: Conference Series
Verified
Conference Paper
Open access
PDF file
KGK V Gogolinskii
K V Gogolinskii
VSV A Syasko
V A Syasko
AUAleksandr Umanskii
Aleksandr Umanskii
ANA A Nikazov
A A Nikazov
TBT I Bobkova
T I Bobkova
The article presents an analysis of the most common hardness measurement methods, implemented by portable hardness testers: rebound or Leeb method, static Portable Rockwell (PR) method and Ultrasonic Contact Impedance (UCI) method. These methods are reviewed in terms of the physical nature of the measurements and the influence of the measured sample properties and the probe parameters on the measurement result. The review contains advantages of each method, possible applications, as well as limitations due to the operation principles of probes. The article also contains the analysis of solving the problem of measurement results validity and their conformity with standardized hardness scales.

13 December 2022 in Inventions
Verified
Journal Article
Open access
PDF file
AVAnna Vinogradova
Anna Vinogradova
Kirill GogolinskyKirill Gogolinsky
Kirill Gogolinsky
AUAleksandr Umanskii
Aleksandr Umanskii
VAVarvara Alekhnovich
Varvara Alekhnovich
ATAlena Tarasova
Alena Tarasova
AMAlena Melnikova
Alena Melnikova
This article is devoted to the study of means and methods for non-destructive testing mechanical properties of polyethylene gas pipelines that have been in operation for 25–55 years. In order to assess mechanical properties, stress at yield was chosen as a key parameter. Stress at yield is determined from the results of tensile tests and is associated with the limiting circumferential (hoop) stress, determined from the results of tests for short-term pressure. Tensile tests require sample cutting and the shutdown of pipelines’ service. To solve this problem of nondestructive testing of pipelines, tests were carried out using the methods of Shore, Leeb and dynamic instrumental indentation. According to the test results, it was revealed that the correlation coefficient between the values of stress at yield and hardness, obtained by the method of dynamic instrumental indentation, is 0.98 which confirms the possibility of the evaluation of the mechanical properties of pipelines by the method of dynamic instrumental indentation.

15 July 2024 in Inventions
Verified
Journal Article
Open access
PDF file
VAVarvara Alekhnovich
Varvara Alekhnovich
VSVladimir Syasko
Vladimir Syasko
AUAleksandr Umanskii
Aleksandr Umanskii
The greatest losses during gas transportation occur in the elements of shut-off valves, the operating parameters of which, among other things, depend on the thickness and hardness of the protective coating of the ball plugs. The study of the parameters of nickel–phosphorus and chrome coatings on ball plugs of serially produced shut-off valves, including control of their thickness and hardness, was carried out. Based on the test results, deviations in the actual parameters of coatings from the requirements of technological documentation were revealed, the necessity of their complex control was substantiated, recommendations on the choice of methods and equipment were formulated, and the main provisions of the test methodology were developed.

28 February 2022 in Inventions
Verified
Journal Article
Open access
PDF file
AUAleksandr Umanskii
Aleksandr Umanskii
Kirill GogolinskyKirill Gogolinsky
Kirill Gogolinsky
VSVladimir Syasko
Vladimir Syasko
AGArtem Golev
Artem Golev
The article is devoted to modification of the impact devices of Leeb hardness testers for the implementation of the dynamic instrumented indentation method. The results obtained made it possible to construct a load–displacement curve using primary EMF signals and made it possible to determine the values of the dissipated and elastic impact body energy, the maximal load of indentation, the maximal and residual penetration depth and the geometric parameters of the indentation region, namely the contact area of the indenter with the surface and the volume of the displaced material. The listed parameters of the indentation process allow us to measure the contact and volume hardness, the elastic modulus and the yield strength of test objects with portable hardness testers.

1 August 2024 in Russian Journal of Nondestructive Testing
Verified
Journal Article
Closed access
PDF file
AGAnton Gorbunov
Anton Gorbunov
PSPavel Solomenchuk
Pavel Solomenchuk
AUAleksandr Umanskii
Aleksandr Umanskii
The paper is devoted to the development of a finite element model of an eddy current probe designed to test the degree of soldering in lap-joint soldered connections of conductive busbars. A methodology for developing a finite element model has been devised that includes a geometric parameter that, when altered, leads to the remeshing of the finite element grid without affecting the test parameters of nondestructive testing. This allows for a series of signal measurements of the finite element model of the eddy current probe, followed by averaging, thereby ensuring acceptable accuracy. The test results confirm the functionality of the eddy current probe, with a defect size measurement range in the soldered joint from 0 to 100% and a guaranteed main absolute error in measuring the degree of soldering of 5%.

15 February 2025 in Applied Sciences
Verified
Journal Article
Open access
PDF file
AGAnton Gorbunov
Anton Gorbunov
VSVladimir Syasko
Vladimir Syasko
PSPavel Solomenchuk
Pavel Solomenchuk
AUAleksandr Umanskii
Aleksandr Umanskii
This article is devoted to the non-destructive testing of the soldering integrity of soldered lap joints of the current-carrying busbars in electrical machines’ stator windings. The design of a two-element eddy current probe with tangentially positioned coils and active shielding for measuring the soldering integrity of soldered lap joints is developed. This paper considers the method of suppressing the influence of stray parameters on the testing results and the method of correcting the measurements in the case of a deviation in the electrical conductivity of the conductive busbar material. The test results demonstrate the performance of the developed eddy current probe for determining the actual value of the soldering integrity of soldered lap joints in the range of 0–100% with a permissible relative error of no more than 5%.