We have studied the excitation and charge transfer (including resonant charge transfer) processes of H and collisions in a wide range of collision energies by solving the time-dependent Schrödinger equation with the classical trajectory approximation for the projectile. The time-dependent Schrödinger equation is solved by the split-operator method with a generalized pseudospectral (nonuniform grid) method. The calculated impact excitation and charge transfer cross sections are in reasonable agreement with the available experimental measurements. Such a time-dependent Schrödinger equation method can be used to study atom-ion collisions in a wide range of collision energies. Moreover, the time-dependent Schrödinger equation method can provide more dynamic information and physical insights. Combined with time-dependent density functional theory, our time propagator holds significant promise for many-electron processes in the interactions of highly charged ions with atoms, molecules, and solids.
1 June 2001 in Journal of the Chinese Chemical Society
A remarkable improvement of ab initio calculations was obtained for wavelengths of (3d4) J = 3 → 2 forbid den transition. Present calculations reduced the long‐standing discrepancy from measurements down to less than 0.2% for most high‐Z titanium‐like ions. In the present calculations, a large extent of configuration space was included so that most important many‐body effects were taken into account. To this end, the linearized second‐order Brillouin‐Wigner perturbation theory was employed with optimized spin‐orbitals. Transition probability and atomic g‐factor were also calculated with the improved atomic wave functions.
3 February 2000 in Journal of Physics B: Atomic, Molecular and Optical Physics
We have studied the mechanisms of giant resonance in 4d photoionization of Eu atoms by density functional theory with the optimized effective potential and self-interaction correction method. The dynamic electron correlation is taken into account by the linear density response method. Our calculated photoionization cross sections in the giant resonance region are in good agreement with experimental measurements. Since Eu is a highly spin polarized system, by decomposing the contribution of 4d electrons in spin-up and spin-down states, we clearly identified that the strong asymmetry line profile of the giant resonance is due to a broad resonance of 4d spin-down electrons interaction with a sharp resonance of 4d spin-up electrons.
9 December 2019 in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
Prestressed concrete sleepers are generally designed taking into account the influence of the dynamic wheel load. In Japan, the dynamic wheel load factor of 2.0 has been typically used for the serviceability limit state since the 1950s. However, there are few examples that have proved its validity. In this study, field measurement tests and three-dimensional numerical analysis were conducted for prestressed concrete sleepers laid on a straight section of a railway track with continuously welded rails. According to the results of the field tests, the measured dynamic wheel load factor was less than the conventionally used dynamic wheel load factor of 2.0, and the bending moments exceeding the full prestress condition, i.e. the compressive stress on all sections, were generated in some cases. Furthermore, even with the prestressed concrete sleepers of the same type laid continuously, the bending moment was increased more than three times due to the support conditions of the prestressed concrete sleepers and the rail roughness. Results of the numerical analyses also revealed that the bending moment was increased more than two times because of the hanging (unsupported) sleepers, and the tensile stress of the prestressed concrete sleeper exceeded 3 N/mm2 when the rail roughness was approximately 2 mm or more. Based on this investigation, the validity of the dynamic wheel load factor of 2.0 was proved.
The ladder sleeper, which is a type of longitudinal sleeper with long beams in the longitudinal direction of the rail, was developed for the maintenance-labor saving of ballast tracks. In this study, to quantify the load distribution performance of the ladder sleepers at the structural boundary, full-scale model tests were conducted to quantify the vibration transmission reduction effect of the ladder sleepers. Following that, numerical experiments were carried out using a three-dimensional numerical analysis model and it was revealed that the ladder sleeper can reduce the pressure on the sleeper bottom plane by approximately 70% when compared to conventional prestressed concrete sleepers. Furthermore, when laying the ladder sleeper at the structural boundary, it was shown that laying across the structural boundary may be more effective in reducing the pressure on the sleeper bottom plane than laying it in front of the structural boundary. Finally, ladder sleepers were installed on the commercial line and long-term measurements of the longitudinal level irregularity verified the effect of suppressing the longitudinal level irregularity of the ballasted ladder track.