XIFANG ZHANG

Dr. XIFANG ZHANG


Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 February 2022 in Micromachines
Verified
Journal Article
Open access
PDF file
XZXIFANG ZHANG
XIFANG ZHANG
ZYZhenqiang Yao
Zhenqiang Yao
ZHZhibao Hou
Zhibao Hou
JSJiacheng Song
Jiacheng Song
Polydimethylsiloxane (PDMS) is hailed as one of the foundational materials that have been applied to different products in various fields because of its chemical resistance, low cost, excellent flexibility, and high molding capability. With the aim to achieve surface texture with high efficiency by means of electrochemical micromachining with PDMS mask, a femtosecond laser is utilized to process a precision array of micro-through-holes on PDMS films as the molds. The ablation process of PDMS with a femtosecond laser was investigated via numerical simulation verified with experiments indicating a laser energy density of 4.865 mJ/mm2 as the ablation threshold of PDMS with the melting temperature of 930 K. The spiral scanning path with optimized radial offset was developed to ablate materials from the PDMS film to form the laminated profiles, and a tapered through hole was then formed with multilayer scanning. The profile dimension and accuracy were examined as control targets in terms of laser pulse energy and scanning speed, showing that a 12 μJ femtosecond laser pulse energy and 1000 mm/s scanning speed could bring about a nearly circular laminating profile with expected smaller exit diameter than the entry diameter. All the cross-section diameters of the microcone decreased with the increase of laser scanning speed, while the taper increased gradually and then saturated around a laser scanning speed of 800 mm/s due to the energy absorption resulting in smaller ablation in diameter and depth.

9 December 2022 in Materials
Verified
Journal Article
Open access
PDF file
ZJZhiyi Jin
Zhiyi Jin
XZXIFANG ZHANG
XIFANG ZHANG
ZHZhibao Hou
Zhibao Hou
ZYZhenqiang Yao
Zhenqiang Yao
Hong ShenHong Shen
Hong Shen
With the aim of improving the durability and reliability of polyetheretherketone (PEEK) composites reinforced with carbon fiber (CF) as thrust bearings without lubricants, a reticulate surface texture was fabricated by plane honing on a stainless steel (SS) counterpart to promote its tribological properties. Pin-on-disk experiments were designed, with the results showing that the reticulate surface texture effectively reduces the friction coefficient from 0.40 to 0.20 compared with the polished SS surface, within the range of the pv value from 0.185 to 1.85 MPa∙m/s. The wear mechanism of the polished SS surface against CF-PEEK, proven with SEM and EDS observations as well as AE measurements, is revealed, falling into abrasive wear with SS particles embedded in the friction interface around the CF strips, causing three-body contact. The reduction in the friction coefficient of the textured SS disk against the CF-PEEK pin can be achieved due to diminution of the CF wear debris and SS particles, which are scraped off by the groove edges and trapped by the groove valleys, reducing the three-body abrasive wear, while the honed plateau is used as a flank surface like a cutting tool to scratch more soft PEEK particles as the transferred film, owing to adhesive wear. This investigation suggests that the SS disk with a honed surface structure can be used as the counterpart of CF-PEEK bearings with a low friction coefficient and wear rate under dry friction.

6 October 2023 in Polymers
Verified
Journal Article
Open access
PDF file
XZXIFANG ZHANG
XIFANG ZHANG
ZYZhenqiang Yao
Zhenqiang Yao
HDHaifeng Du
Haifeng Du
JSJiacheng Song
Jiacheng Song
ZJZhiyi Jin
Zhiyi Jin
WXWei Xu
Wei Xu
With the aim of promoting the qualities for total hip joint replacement, the wettability and tribological behaviors of PEEK composites pins with two sets of different fillers (PEEK/CF or PEEK/CF/PTFE/graphite) against Co-Cr alloy discs with five categories of surface textures (polished, orthogonal, spiral, r-θ, and orthogonal combined with spiral) were explored. It is revealed that the existence of CF in PEEK matrix increases the hydrophilicity in addition to the strength of PEEK, while the addition of PTFE increases the hydrophobicity of PEEK. The Co-Cr alloy discs with hydrophilic properties can be adjusted as hydrophobic, with the depth of textured grooves exceeding the critical sag height determined by the contact angle and the groove width. It can be concluded that PEEK/CF/PTFE/graphite composite has a lower wear rate than PEEK only reinforced with CF against Co-Cr alloy, both without surface texture and with shallow or deep grooves. The existence of shallow grooves on the disc surface could help the PEEK blends to achieve a steady friction against Co-Cr alloy in addition to collecting the worn debris. PEEK blend pins with 10 vol% CF, 10 vol% PTFE and 10 vol% graphite can achieve a lower friction coefficient of no more than 0.2 against Co-Cr alloy discs with shallow grooves around 3.5 μm in orthogonal or spiral textures.

27 July 2019 in Journal of Applied Electrochemistry
Verified
Journal Article
Closed access
PDF file
XZXIFANG ZHANG
XIFANG ZHANG
HLHua Li
Hua Li
ZYZhen Yin
Zhen Yin
KRKun Ren
Kun Ren

27 December 2022 in Materials
Verified
Journal Article
Open access
PDF file
XZXIFANG ZHANG
XIFANG ZHANG
ZHZhibao Hou
Zhibao Hou
JSJiacheng Song
Jiacheng Song
ZJZhiyi Jin
Zhiyi Jin
ZYZhenqiang Yao
Zhenqiang Yao
Silicon carbide (SiC) has a variety of applications because of its favorable chemical stability and outstanding physical characteristics, such as high hardness and high rigidity. In this study, a femtosecond laser with a spiral scanning radial offset of 5 μm and a spot radius of 6 μm is utilized to process micropillars on a SiC plate. The influence of pulsed laser beam energies and laser translation velocities on the micropillar profiles, dimensions, surface roughness Ra, and material removal capability (MRC) of micropillars was investigated. The processing results indicate that the micropillar has the best perpendicularity, with a micropillar bottom angle of 75.59° under a pulsed beam energy of 50 μJ in the range of 10–70 μJ, with a pulsed repetition rate of 600 kHz and a translation velocity of 0.1 m/s. As the laser translation velocity increases between 0.2 m/s and 1.0 m/s under a fixed pulsed beam energy of 50 μJ and a constant pulsed repetition rate of 600 kHz, the micropillar height decreases from 119.88 μm to 81.79 μm, with the MRC value increasing from 1.998 μm3/μJ to 6.816 μm3/μJ, while the micropillar bottom angle increases from 68.87° to 75.59°, and the Ra value diminishes from 0.836 μm to 0.341 μm. It is suggested that a combination of a higher pulsed laser beam energy with a faster laser translation speed is recommended to achieve micropillars with the same height, as well as an improved processing efficiency and surface finish.

21 November 2025 in Applied Physics A
Verified
Journal Article
Closed access
PDF file
ZQZixuan Qie
Zixuan Qie
YLYuchen Lou
Yuchen Lou
XZXIFANG ZHANG
XIFANG ZHANG
ZYZhenqiang Yao
Zhenqiang Yao