In this paper, silicon carbide fiber-reinforced silicon carbide (SiC_f/SiC) composites were fabricated using binder jetting additive manufacturing followed by polymer infiltration and pyrolysis. Spherical SiC powders were produced using milling, spray drying, and thermal plasma treatment, and were characterized using SEM and XRD methods. Irregularly shaped and spherical SiC powders were used to obtain SiC_f/SiC blends for the application in binder jetting. The effect of SiC powder shape on densification behavior, microstructure, and mechanical properties of binder jetted SiC_f/SiC composites was evaluated. The highest density of 2.52 g/cm³ was obtained after six polymer infiltration and pyrolysis cycles. The microstructure and mechanical properties of the fabricated SiC_f/SiC composites were characterized. Using the spherical SiC powder resulted in higher fracture toughness and hardness, but lower flexural strength compared to the irregularly shaped powder. It was shown that it is feasible to fabricate dense SiC_f/SiC composites using binder jetting followed by polymer infiltration and pyrolysis.

Three-dimensional laser scanning is a novel measurement technique that is frequently used for the documentation of cultural heritage (CH) objects. In the process of 3D scanning, one can obtain computing 3D models of artworks to be documented. It allows one to produce detailed digitized archives of important CH objects. Moreover, the use of 3D scanning enables the digital reconstruction of architectural fragments, sculptures, and other artworks. One more important application of this technique relates to the creation of molds and replicas for replacements of outdoor CH objects in case their preservation requirements do not allow them to remain in their original place due to the influence of environmental factors. One of the most effective ways of creating replicas is the use of laser additive technologies. Therefore, the combination of 3D scanning and additive technologies is a very promising way of preservation of CH. This paper describes several case studies concerned with the combined usage of 3D laser scanning and additive technologies for digital reconstruction and replication and of outdoor sculptures in St. Petersburg city. One of them is the reconstruction of the zinc sculpture “Eva at the fountain” (XIX century, England), which was destroyed during WWII. Its replica was created by means of laser stereolithography. Eventually, one more project is related to the reconstruction of the fragment of the sufficiently damaged cast-iron XIX century monument. This object was reconstructed using two laser technologies: direct metal laser sintering (DMLS), and laser cladding (LC).

Additive manufacturing is a very rapidly developing industrial field. It opens many possibilities for the fast fabrication of complex-shaped products and devices, including functional materials and smart structures. This paper presents an overview of polymer 3D printing technologies currently used to produce magnetic materials and devices based on them. Technologies such as filament-fused modeling (FDM), direct ink writing (DIW), stereolithography (SLA), and binder jetting (BJ) are discussed. Their technological features, such as the optimal concentration of the filler, the shape and size of the filler particles, printing modes, etc., are considered to obtain bulk products with a high degree of detail and with a high level of magnetic properties. The polymer 3D technologies are compared with conventional technologies for manufacturing polymer-bonded magnets and with metal 3D technologies. This paper shows prospective areas of application of 3D polymer technologies for fabricating the magnetic elements of complex shapes, such as shim elements with an optimized shape and topology; advanced transformer cores; sensors; and, in particular, the fabrication of soft robots with a fast response to magnetic stimuli and composites based on smart fillers.

Additive manufacturing (AM) is a rapidly developing technical field that is becoming an irreplaceable tool to fabricate unique complex-shaped parts in aerospace, the automotive industry, medicine, and so on. One of the most promising directions for AM application is the design and production of multi-material components with different types of chemical, structural, and architectural gradients that also promote a breakthrough in bio-inspired approaches. At the moment there are a lot of different AM techniques involving various types of materials. This paper represents a review of extrusion-based AM techniques using metal-polymer composites for structural metal parts fabrication. These methods are significantly cheaper than powder bed fusion (PBF) and directed energy deposition (DED) techniques, though have a lower degree of part detail. Thus, they can be used for low-scale production of the parts that are not rentable to produce with PBF and DED. Multi-material structures application in machinery, main aspects of feedstock preparation, the subsequent steps of extrusion-based 3D printing, and the following treatment for manufacturing single-metallic and multi-metallic parts are considered. Main challenges and recommendations are also discussed. Multi-metallic extrusion-based 3D printing is just a nascent trend requiring further wide investigation, though even now it shows pretty interesting results.