This study focuses on the synthesis of TiC-TiB2/Fe coatings with varying amounts of aluminum (Al) using tungsten inert gas (TIG) cladding and investigates the impact of Al addition on microstructure refinement and performance enhancement of the coatings. The coatings were prepared on a mild steel substrate using TIG cladding. X-ray diffraction (XRD) analysis revealed the presence of TiC, TiB2, AlxTi, and AlxFe phases in the coatings. Scanning electron microscopy (SEM) images showed that the addition of Al improved the microstructure, reducing defects and enhancing the distribution of reinforcing phases within the coatings. The particle size of the reinforcing phases was significantly refined by the addition of Al. The micro-hardness of the coatings was significantly higher than that of the substrate, with the maximum micro-hardness of the coating reaching 955.5 ± 50.7 HV0.1, approximately six times that of the substrates. However, excessive Al addition led to a reduction in hardness due to a decrease in the quantity of hard phases. The wear tests showed that all the coatings had lower wear loss compared to the substrate material, with the wear loss initially decreasing and then increasing with the increasing Al content. Samples with a 28.57 wt.% Al addition exhibited the best wear resistance, with approximately 16.8% of the wear volume loss compared to mild steel under the same testing conditions, attributed to the optimal combination of reinforcement phase quantity and matrix properties.
A two dimensional (2D) transient thermal model with line-heat-source was developed by Finite Element Method (FEM) for laser surface glazing of H13 tool steel using commercial software-ANSYS 15. The geometry of the model was taken as a transverse circular cross-section of cylindrical specimen. Two different power levels (300W, 200W) were used with 0.2mm width of laser beam and 0.15ms exposure time. Temperature distribution, heating and cooling rates, and the dimensions of modified surface were analysed. The maximum temperatures achieved were 2532K (2259°C) and 1592K (1319°C) for laser power 300W and 200W respectively. The maximum cooling rates were 4.2×107 K/s for 300W and 2×107 K/s for 200W. Depths of modified zone increased with increasing laser power. From this analysis, it can be predicted that for 0.2mm beam width and 0.15ms time exposer melting temperature of H13 tool steel is achieved within 200-300W power range of laser beam in laser surface glazing.
In this work a three dimensional (3D) finite element model of laser surface glazing (LSG) process has been developed. The purpose of the 3D thermal model of LSG was to achieve maximum accuracy towards the predicted outcome for optimizing the process. A cylindrical geometry of 10mm diameter and 1mm length was used in ANSYS 15 software. Temperature distribution, depth of modified zone and cooling rates were analysed from the thermal model. Parametric study was carried out varying the laser power from 200W-300W with constant beam diameter and residence time which were 0.2mm and 0.15ms respectively. The maximum surface temperature 2554°K was obtained for power 300W and minimum surface temperature 1668°K for power 200W. Heating and cooling rates increased with increasing laser power. The depth of the laser modified zone attained for 300W power was 37.5µm and for 200W power was 30µm. No molten zone was observed at 200W power. Maximum surface temperatures obtained from 3D model increased 4% than 2D model presented in author’s previous work. In order to verify simulation results an analytical solution of temperature distribution for laser surface modification was used. The surface temperature after heating was calculated for similar laser parameters which is 1689°K. The difference in maximum surface temperature is around 20.7°K between analytical and numerical analysis of LSG for power 200W.
Ti64 alloy plays a significant role in the biomedical applications such as bioimplants for its excellent biocompatibility. Its usage can be further extended by improving the surface hardness and wear resistance. In this respect, laser surface glazing (LSG), an advanced surface modification technique, is very useful which can produce thin hardened surface layer and strong metallurgical bonding. Investigation of temporal and spatial temperature distributions of laser glazed surface of materials are essential because temperature plays significant role in achieving required surface properties. Therefore, in this study, a 3D Finite element analysis has been developed to perform transient thermal analysis of LSG for Ti64 alloy. The model investigated temperature distribution, depth of modified zone and heating and cooling. The results show that the peak temperature is attained 2095 K for 300 W laser power, 0.2 mm beam width and 0.15 ms residence time. Since this temperature is above the melting point (1933 K) of Ti64 alloy, the melt depth is calculated 22.5 μm. Furthermore, from the simulation results, the average heating and cooling rates are estimated 1.19×107 Ks-1 and 2.71×106 Ks-1 respectively which indicate the presence of hard phases in the modified zone.