Zhiqiang Wang

Dr. Zhiqiang Wang


Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 May 2014 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
CZChenkai Zhang
Chenkai Zhang
ZWZhiqiang Wang
Zhiqiang Wang
CYChao Yin
Chao Yin
WYWei Yan
Wei Yan
JHJun Hu
Jun Hu
This paper discusses detailed experimental studies of a low-speed large-scale axial compressor, which is typical of an exit stage of HPC. Numerous measuring techniques were performed, and detailed experimental results were obtained, including inlet boundary layer total pressure distributions, overall compressor and model-stage performance, traverse flow field between blade rows and inside the stator for the model stage, static pressure on the stator blade and casing dynamic pressure of the rotor. The objective of the study is to assess the low-speed model compressor design and verify 3D computational fluid dynamics (CFD) code. Results show that inlet endwall blockage requirement of HPC exit stage is achieved; the low-speed model compressor design is fundamentally successful; the flow rate and pressure rise requirements are met at the design operating point, although the flow loss is relatively larger than design values for the lower half span, which can be attributed to a certain hub-corner separation. Furthermore, the reliability of adopted 3D commercial CFD code is validated. It is proved that the low-speed model testing technique is still a prospective way for the design of high performance HPC.

31 March 2021 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
XWXuegao Wang
Xuegao Wang
JHJun Hu
Jun Hu
JGJin Guo
Jin Guo
CJChao Jiang
Chao Jiang
ZWZhiqiang Wang
Zhiqiang Wang
Owing to the manufacturing and assembly error or the fatigue of long-time operation, nonaxisymmetric tip clearance is actually a common phenomenon in compressors. It is also well accepted that tip leakage flow, associated with tip clearance size and loading, has a strong influence on the performance and stall inception of compressors. The work of this paper, based on an eccentric compressor with/without inlet swirl distortion, is aimed at strengthening the understanding of stall inception for a real geometry compressor experimentally. Results indicate that rotor tip blockage and flow unsteadiness vary evidently around the circumference. For this compressor, the maximum tip flow unsteadiness and blockage happens at the location near the minimum clearance under the condition of clean inlet flow. Before the occurrence of stall inception, disturbances arise and vanish intermittently within the region of high unsteadiness. However, it fails to rotate due to the inhibition of the low unsteadiness region. Once the most robust region is no longer able to suppress disturbances, stability finally breaks down and stall inception generates. After exerting inlet paired swirl, unsteadiness within the region of positive preswirl decreases significantly and the maximum unsteadiness location shifts, while the increase for the region with negative preswirl is nearly negligible. As a result, stall margin of the compressor is improved.

31 January 2014 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
CZChenkai Zhang
Chenkai Zhang
HJHu Jun
Hu Jun
ZWZhiqiang Wang
Zhiqiang Wang
XGXiang Gao
Xiang Gao
Low-speed model testing has advantages such as great accuracy and low cost and risk, so it is widely used in the design procedure of the high pressure compressor (HPC) exit stage. The low-speed model testing project is conducted in Nanjing University of Aeronautics and Astronautics (NUAA) to represent aerodynamic load and flow field structure of the seventh stage of a high-performance ten-stage high-pressure compressor. This paper outlines the design work of the low speed four-stage axial compressor, the third stage of which is the testing stage. The first two stages and the last stage provide the compressor with entrance and exit conditions, respectively. The high-to-low speed transformation process involves both geometric and aerodynamic considerations. Accurate similarities demand the same Mach number and Reynolds number, which will not be maintained due to motor power/size and its low-speed feature. Compromises of constraints are obvious. Modeling principles are presented in high-to-low speed transformation. Design work was carried out based on these principles. Four main procedures were conducted successively in the general design, including establishment of low-speed modeling target, global parameter design of modeling stage, throughflow aerodynamic design, and blading design. In global parameter design procedure, rotational speed, shroud diameter, hub-tip ratio, midspan chord, and axial spacing between stages were determined by geometrical modeling principles. During the throughflow design process, radial distributions of aerodynamic parameters such as D-factor, pressure-rise coefficient, loss coefficients, stage reaction, and other parameters were obtained by determined aerodynamic modeling principles. Finally, rotor and stator blade profiles of the low speed research compressor (LSRC) at seven span locations were adjusted to make sure that blade surface pressure coefficients agree well with that of the HPC. Three-dimensional flow calculations were performed on the low-speed four-stage axial compressor, and the resultant flow field structures agree well with that of the HPC. It is worth noting that a large separation zone appears in both suction surfaces of LSRC and HPC. How to diminish it through 3D blading design in the LSRC test rig is our further work.

1 November 2024 in Journal of Aerospace Engineering
Verified
Journal Article
Closed access
HJHui-Jie Jin
Hui-Jie Jin
YZYong-Ping Zhao
Yong-Ping Zhao
ZWZhiqiang Wang
Zhiqiang Wang
KHKuan-Xin Hou
Kuan-Xin Hou

1 January 2016 in International Journal of Turbo & Jet-Engines
Verified
Journal Article
Closed access
ZWZhiqiang Wang
Zhiqiang Wang
LBLu Bo
Lu Bo
ZCZhang Chenkai
Zhang Chenkai
HJHu Jun
Hu Jun
In order to realize the stator’s internal flow field measurement of the multi-stage axial compressor, many different lengths of L-type five-hole probes and one four-hole probe have been designed. The detailed 3D (three-dimensional) flow fields in the stator blade passage of original and modified large scale compressors have been measured with the probes traversed by a probe traverse mechanism. The objective of the study is to assess the measurement method of adopting multi-hole pneumatic probes to achieve the flow field of stator vane passage. Results clearly demonstrate the flow field characteristics of stator blade passage in original and modified compressors. Furthermore, the reliability of adopted multi-hole pneumatic probes is validated. Therefore, it is proved that the probe traverse mechanism drives the L-type five-hole probe or other probe method can be applied to internal flow field measurements for the stator of large scale multi-stage compressors.

12 January 2016 in International Journal of Turbo & Jet-Engines
Verified
Journal Article
Closed access
ZWZhiqiang Wang
Zhiqiang Wang
SXShen Xigang
Shen Xigang
HJHu Jun
Hu Jun
XGXiang Gao
Xiang Gao
LLLiu Liping
Liu Liping
A numerical method was developed to predict the aerodynamic stability of a high bypass ratio turbofan engine, at the landing stage of a large transport aircraft, when the thrust reverser was deployed. 3D CFD simulation and 2D aeroengine aerodynamic stability analysis code were performed in this work, the former is to achieve distortion coefficient for the analysis of engine stability. The 3D CFD simulation was divided into two steps, the single engine calculation and the integrated aircraft and engine calculation. Results of the CFD simulation show that with the decreasing of relative wind Mach number, the engine inlet will suffer more severe flow distortion. The total pressure and total temperature distortion coefficients at the inlet of the engines were obtained from the results of the numerical simulation. Then an aeroengine aerodynamic stability analysis program was used to quantitatively analyze the aerodynamic stability of the high bypass ratio turbofan engine. The results of the stability analysis show that the engine can work stably, when the reverser flow is re-ingested. But the anti-distortion ability of the booster is weaker than that of the fan and high pressure compressor. It is a weak link of engine stability.