This paper is devoted to improvement of environmental safety in hydrocarbon-firing TPPs. Despite the development of renewable power sources, the number of traditional power production facilities continues its growth. The toxic emission mitigation in traditional TPPs has been deeply investigated, but the problem of greenhouse gas atmospheric emissions is of topical interest. Oxy-fuel technology reduces CO2 emissions and is highly efficient and environmentally safe. Also, it requires relatively low capital investments. Thermal efficiency analysis shows that the Allam cycle facilities have the best efficiency. Their thermodynamic parameters can be optimized with minimal primary costs and capital investments. This newly developed analysis was used to compare the investment efficiency of projects for the buildup of oxy-fuel and combined cycle facilities. Without emission quote payments, the NPV of combined cycle projects is 16% higher, as well as having a lower DPP. The electricity production primary costs in oxy-fuel and combined cycle facilities are similar, which reflects the technologies’ similarity and similar fuel costs. Implementation of carbon dioxide emission quote marketing makes oxy-fuel facilities more investment-attractive. Parametric studies show that when Russia implements CO2 emission quotes compatible with the current EU level, an oxy-fuel facility erection project will be financially reasonable. Thus, it can be concluded that the construction of oxy-fuel power plants is one of the most promising and investment-attractive solutions to reduce CO2 emissions in the energy sector for large industrialized countries. The managerial consequences of their implementation will include the stabilization of greenhouse gas emissions while ensuring the financial stability of the energy industry.
There is a steady trend in the world to increase the share of distributed generation. The volume of self-generated energy commissioning is constantly growing, with projected increases in growth rates in the future. At the same time, demands for efficiency and environmental safety in new power plants are constantly increasing. In this regard, one of the promising areas for the development of distributed energy is the transition to small nuclear power plants (SNPPs). As in the case of wind and solar power plants, SNPP operations are not accompanied by emissions of toxic substances or greenhouse gases into the atmosphere. In addition, SNPPs consume a much smaller volume and mass of fuel compared to conventional small-capacity fossil fuel power plants. This paper describes the characteristics of the main types of distributed generation. The key technical and economic characteristics of existing and prospective small-capacity nuclear fuel facilities are systematized. The results of a comparative analysis of the cost of electricity produced by SNPPs and competing power plants are also presented. In addition, a number of promising regions of the Russian Federation for the introduction of SNPPS have been identified, and a review of the methods of energy storage for SNPPS, which are necessary when working in an isolated power system, has been carried out.
The Rankine cycle is widely used for electricity production. Significant weight and size characteristics of the power equipment working on superheated steam are the main disadvantages of such power plants. The transition to supercritical carbon dioxide (S-CO2) working fluid is a promising way to achieve a significant reduction in equipment metal consumption and to increase energy efficiency. This paper presents the results of thermodynamic analysis of S-CO2 thermal power plants (TPPs) utilizing the heat of combustion products of an energy boiler. It was found that the net efficiency of the developed S-CO2 TPP with a pulverized coal-fired boiler reached 49.2% at an initial temperature of 780 °C, which was 2% higher compared to the efficiency level of steam turbine power plants (STPPs) at a similar turbine inlet temperature.
The paper is concerned with the problem of the development of high-temperature steam turbine power plants with ultra-supercritical (USC) initial parameters. One of the main disadvantages of the USC power unit’s creation is high price due to the application of expensive heat-resistant materials for boiler, live and reheat steam pipelines in turbines. To solve this problem, the following technical improvements to reduce the application of the heat-resistant materials and equipment metal consumption are proposed: horizontal boiler layout, high temperature steam turbine with a cooling system, oxy-hydrogen combustion chambers, and two-tier low-pressure turbine. The influence of the above-mentioned solutions on the high-temperature steam turbine power plant efficiency was estimated using thermodynamic analysis. The promising equipment design was developed based on the results of numerical and experimental research. The analysis of the proposed solutions’ influence upon the economic parameters of a high-temperature power facility was investigated based on the developed cost analysis model, which included the equipment metal and manufacturing expenses. The introduction of all the mentioned cost reduction methods led to a decrease in the facility’s price by RUB 10.5 billion or 15%. The discounted payback period was reduced from 27.5 to 10 years and the net present value increased by RUB 9.6 billion or 16 times.
The most effective and environmentally safe fossil fuel power production facilities are the combined cycle gas turbine (CCGT) ones. Electric efficiency of advanced facilities is up to 58% in Russia and up to 64% abroad. The further improvement of thermal efficiency by increase of the gas turbine inlet temperature (TIT) is limited by performance of heat resistance alloys that are used for the hot gas path components and the cooling system efficiency. An alternative method for the CCGT efficiency improvement is utilization of low potential heat of the heat recovery steam generator (HRSG) exhaust gas in an additional cycle operating on a low-boiling heat carrier. This paper describes a thermodynamic analysis of the transition from binary cycles to trinary ones by integration of the organic Rankine cycle (ORC). A mathematical model of a cooled gas turbine plant (GT) has been developed to carry out calculations of high-temperature energy complexes. Based on the results of mathematical modeling, recommendations were made for the choice of the structure and parameters of the steam turbine cycle, as well as the ORC, to ensure the achievement of the maximum thermal efficiency of trinary plants. It is shown that the transition from a single pressure CCGT to a trinary plant allows the electric power increase from 213.4 MW to 222.7 MW and the net efficiency increase of 2.14%. The trinary power facility has 0.45% higher efficiency than the dual pressure CCGT.
Thermal power plants (TPPs) with back-pressure steam turbines (BPSTs) were widely used for electricity and steam production in the Union of Soviet Socialist Republics (USSR) due to their high efficiency. The collapse of the USSR in 1991 led to a decrease in industrial production, as a result of which, steam production in Russia was reduced and BPSTs were left without load. To resume the operation of TPPs with BPSTs, it is necessary to modernize the existing power units. This paper presents the results of the thermodynamic analysis of different methods of modernization of TPPs with BPSTs: the superstructure of the steam low-pressure turbine (LPT) and the superstructure of the power unit operating on low-boiling-point fluid. The influence of ambient temperature on the developed cycles’ efficiency was evaluated. It was found that the usage of low-boiling-point fluid is thermodynamically efficient for an ambient temperature lower than 7 °C. Moreover, recommendations for the choice of reconstruction method were formulated based on technical assessments.