Wenjie Zhao

Wenjie Zhao


Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 March 2025 in Polymers
Verified
Journal Article
Open access
PDF file
NKNing Kuang
Ning Kuang
MXMinghui Xiao
Minghui Xiao
HQHao Qi
Hao Qi
WZWenjie Zhao
Wenjie Zhao
JWJunfei Wu
Junfei Wu
In ceramic digital light processing (DLP) additive manufacturing, the photosensitive resin, which acts as a carrier for ceramic particles, must exhibit suitable curing performance, curing strength, and viscosity. This ensures both the bonding strength of the fabricated ceramic parts and the dimensional accuracy of the ceramic green body. In this study, various photosensitive resin monomers were investigated in depth to formulate resins containing monofunctional, bifunctional, and multifunctional groups. Their rheological and curing properties were analyzed theoretically and experimentally. Different resin slurry systems were prepared and printed using DLP technology, and their mechanical properties were tested and compared. The effect of photoinitiator content on the curing behavior of the resin was examined, and the optimal photoinitiator concentration was identified. Based on the optimized resin, a zirconia ceramic slurry with 56 vol% solid content was prepared. After DLP printing, debinding, and sintering, dense zirconia ceramic samples with a relatively uniform grain structure were obtained, exhibiting a bending strength of 766.85 MPa. These results significantly expand the potential applications for zirconia ceramic components with complex geometries.

26 February 2022 in Processes
Verified
Journal Article
Open access
PDF file
HWHao Wang
Hao Wang
JWJunfei Wu
Junfei Wu
PFPing Fu
Ping Fu
ZQZhiping Qu
Zhiping Qu
WZWenjie Zhao
Wenjie Zhao
YSYixuan Song
Yixuan Song
In the surface filtration process with pores larger than the particle size, the formation of particle bridges plays a crucial role in the filter cake structure and the filtration efficiency throughout the filtration process. First, to understand the microscopic information required for the bridging mechanism, we use the two-way coupling of computational fluid dynamics (CFD)–discrete element method (DEM) to simulate the deposition characteristics of particles in the pores of ceramic membranes. Next, by dynamically observing the deposition morphology and bridging process of particles, the bridging mechanism was revealed at the level of a single hole. Then, we studied the influence of particle concentration and inlet velocity on the bridge erection process. The results show that the bridging function of particles runs through the clean filtration stage and the transition stage. Particle concentration and inlet flow rate have a crucial influence on the formation of particle bridges and filtration efficiency.

15 May 2025 in Polymers
Verified
Journal Article
Open access
PDF file
NKNing Kuang
Ning Kuang
HQHao Qi
Hao Qi
WZWenjie Zhao
Wenjie Zhao
JWJunfei Wu
Junfei Wu
Digital light processing (DLP) is widely recognized as one of the most promising additive manufacturing technologies for ceramic fabrication. Nevertheless, during the additive manufacturing of zirconia ceramics, debinding and sintering often lead to structural defects, which severely deteriorate the material properties and hinder their broader application. In this study, we added an oligomer into the photosensitive resin and systematically investigated the effects of oligomer content on the viscosity and curing properties of ceramic suspensions. The results demonstrated that the introduction of oligomers is conducive to enhancing the crosslinking density and reducing defects. Finally, a 45 vol% solid content zirconia ceramic slurry was prepared by adding 20 wt% oligomers to the resin system. After printing, debinding, and sintering, the final zirconia ceramics exhibited a uniform microstructure without delamination or cracks, its bending strength reached 682.4 MPa. This study demonstrates that zirconia ceramics fabricated by photopolymerization with oligomer photosensitive resin exhibit excellent mechanical properties, significantly expanding the potential applications for high-performance zirconia ceramic components with additive manufacturing.

11 January 2023 in Polymers
Verified
Journal Article
Open access
PDF file
WZWenjie Zhao
Wenjie Zhao
YWYu Wang
Yu Wang
Qingdang LiQingdang Li
Qingdang Li
To address the problem of lignin membrane fouling caused by dynamic cross-flow in the process of retaining and concentrating the black liquor byproduct of papermaking, this paper uses three different rotating structures (vane, disk and propeller) to increase the surface shear force and filtration flux of the membrane. In this paper, under different rotating speeds and different transmembrane pressure differences, numerical simulations were conducted on the shear forces generated by the three structures and the retention process on the surface of the membrane. The variation laws were also studied and compared. Under the same filtration conditions, the vane structure demonstrates better results than the propeller and disk structures in terms of increasing filtration flux. Based on the result, the vane shear force was simulated in terms of changing the particle deposition, and compared with vane rotating speeds of 100–700 r/min, the surface particle deposition of the membrane was significantly reduced at a rotating speed of 800 r/min. Finally, the numerical simulation results were experimentally validated to ensure the accuracy of the simulation. The findings provide a theoretical basis and practical value for solving the problem of lignin membrane fouling caused by dynamic cross-flow in the process of retaining and concentrating the black liquor byproduct of papermaking.

21 May 2025 in Polymers
Verified
Journal Article
Open access
PDF file
WWWeikang Wang
Weikang Wang
NKNing Kuang
Ning Kuang
WZWenjie Zhao
Wenjie Zhao
QLQingdang Li
Qingdang Li
Among the various methods for recovering lignin from black liquor, membrane separation has gained prominence in the paper industry due to its advantages of uniform molecular weight distribution, high recovery rates, and absence of secondary pollution. However, over time, lignin particles tend to deposit and form a cake layer on the membrane surface, leading to membrane fouling and a decline in filtration flux. To address this issue, this study investigates the construction of ceramic membranes with radial rib patterns, and examines the effects of different trans-membrane pressure differences and radial rib patterns on membrane surface shear force and particle deposition. The research findings indicate that at a trans-membrane pressure difference of 0.5 bar and a blade rotation speed of 1000 r/min, the membrane surface experiences the highest shear force. Compared with those without patterns, ceramic membranes with radial rib patterns can more effectively delay the deposition of particles. Furthermore, it was observed that ceramic membranes combining coarse and fine rib patterns exhibit a more pronounced increase in membrane surface shear force.

16 October 2025 in Polymers
Verified
Journal Article
Open access
PDF file
NKNing Kuang
Ning Kuang
WZWenjie Zhao
Wenjie Zhao
JWJunfei Wu
Junfei Wu
Aluminum nitride (AlN) ceramics exhibit exceptional properties, making them attractive for a wide range of applications. To address the growing need for customized and geometrically intricate AlN components, digital light processing (DLP) has garnered significant interest as a highly promising additive manufacturing technology. In this study, the effects of the sintering process on DLP 3D printing of AlN ceramics were investigated. An optimized slurry formulation with a solid loading of 52 vol% was developed, exhibiting excellent rheological properties. By applying a controlled sintering heating rate of 0.5 °C/min, dense AlN ceramic components were successfully fabricated, achieving a bending strength of 212.6 MPa. This provides a novel approach for optimizing the DLP additive manufacturing process of AlN ceramics.