Mine dust is one of the main disasters that threatens the safety of coal mine production, deteriorates the underground working environment and induces various occupational diseases. Based on the harm of mine dust identified and the current domestic and foreign dust-proof technology, the technical research of the foam dust reduction is reviewed; the advantages and disadvantages of foam dust reduction are also discussed. According to the experimental exploration and the study of foam flow characteristics, the process of foam device and foam nozzle separation was adopted, and some site tests were conducted in fully mechanized mining and excavation working faces in Zhangcun, Shanjiaoshu and Jinjia coal mines. The foam technology led to a 59.5% dust removal efficiency in Zhangcun coal mine, which is much higher than the dust removal efficiency of the water spray dust reduction. The efficiency of total mine dust in Shanjiaoshu coal mine reached as high as 72%, and the efficiency of respirable mine dust reached 67%. Compared with the circumstance with no dust-control measure, the average density of the total mine dust in Jinjia coal mine decreased by 22.75~32.95% using foam technology. The results show that the use of the foam to inhibit the transformation of mine dust from the source of dust production to the floating state and the efficiency of dust control is greatly improved. This method can effectively reduce the mine dust density in underground mining and excavation working faces, clean the working environments, and guarantee the health of miners. The research results are of great significance for improving the production conditions of mining and excavating face and building green mines and standardized mines. Moreover, foam technology for dust control has been widely used in coal mines.
Through studying the mechanics, energy, and deformation features of rock under uniaxial cyclic loading and unloading, the findings are as follows: (1) under cyclic loading and unloading, the curve of stress and strain for loading and unloading in every cycle was not superposition reciprocally but formed an acutifoliate hysteresis loop. The distribution of the hysteresis loop became denser with the cycles and moved toward the direction of strain increasing. (2) The area of the hysteresis loop indicated the inner damage degree of rock. And the hysteresis energy accumulated was stronger; the damage of rock was more serious. Furthermore, the hysteresis energy grew linearly along with load, and the hysteresis energy accumulated had a trend exponential growth with cycle continuing. (3) The elasticity modulus grew in the form of logarithm as a whole. In each cycle, elasticity modulus for unloading was greater than that for loading. When it exceeded a certain value, elasticity modulus for reloading was less than elasticity modulus for unloading. (4) The cyclic loading and unloading had a strength impact that was gradually stronger and stronger as the cycle went on the sample of rock.
22 November 2019 in Journal of Geophysics and Engineering
In-situ rock stress was measured in the development roadway of Gucheng coal mine at +420 m level by using the stress relief method of hollow inclusion. The results show that the first principal stress was the vertical stress, the maximum horizontal principal stresses were distributed in the range of N10°E and N20°E, and the average side pressure coefficient was 0.83. There was a large difference between the maximum horizontal principal stress and the minimum horizontal principal stress, and the calculated average ratio was 2.02. A spatial stress conversion model of the horizontal roadway based on the measured in-situ rock stresses was built, and the distribution laws of stress and displacement of the surrounding rock of the roadway were analyzed in depth along the changing radial direction. According to the Mohr–Coulomb failure criterion, an asymmetric surrounding rock plastic zone was obtained and the plastic failure radius was 5.0 m. Considering the roadway-surrounding rock differential control, the stronger support in the risk areas was practiced and validated. The work in this paper would provide some ideas for the design and optimization of the support parameters for roadway engineering.
In order to further explore the relationship between the excavation speed and the damage of surrounding rocks and dynamic manifestation, the stress paths of unloading confining pressure and loading axial pressure were designed based on the changes in the roadway surrounding rock stress in this study. Additionally, the mechanical properties and energy evolution law of the coal body were investigated under various unloading rates. As the unloading rate increased, the mechanical properties of the coal body including the failure strength, the confining pressure, the axial strain, and horizontal strain tended to decrease at the rupture stage, while the volume strain and the elastic modulus increased, indicating that the rupture form evolved from the ductile failure to brittle failure. Regarding the energy, the axial pressure did positive work while the confining pressure did negative work, with the total work and the stored elastic strain energy decreasing. In addition, with the increase of the dissipation energy, the elastic strain energy conversion rate decreased linearly, indicating that the high unloading rate increased the possibility of dynamic disasters induced by the instantaneous brittle rupture of the coal body. On the other hand, due to the low releasable elastic strain energy stored in the coal body, the strength and probability of subsequent dynamic manifestation of coal body destruction were reduced. Therefore, increasing the excavation speed in a controllable way can benefit the safety of mining.
In order to further explore the deformation and failure essence of the deep coal body, based on the characteristics of surrounding rock stress adjustment before and after solid coal roadway excavation, an experiment of unloading confining pressure and loading axial pressure of the coal body was designed and conducted in this study. Based on test results, the failure mechanics and energy characteristics of the coal body were analyzed through experiments. Rapid unloading is considered a key factor contributing to lateral deformation and expansion failure, which exacerbates the deterioration of coal body and reduces the deformation energy storage capacity of coal. On the other hand, the larger loading rate tends to shorten the accumulation time of microcracks and cause damage to the coal body, resulting in strengthening the coal body and improving energy storage. Under the circumstance that the coal body is destroyed, the conversion rates of the internal deformation energy and dissipated energy are more significantly affected by unloading rate. The increasing unloading rate and rapid decreases in the conversion rate of deformation energy make the coal body more vulnerable to damage. Under the same stress conditions, the excavation unloading is more likely to deform, destroy, or even throw the coal than the experiment unloading. In order to reduce or avoid the occurrence of deep roadway excavation accidents, the understanding of the excavation unloading including possible influencing factors and the monitoring of the surrounding rock stress and energy during the excavation disturbance should be strengthened. It can be used as the basis for studying the mechanism of deformation and failure of coal and rock and dynamic disasters in deep mines, as well as the prediction, early warning, prevention, and control of related dynamic disasters.
The research on the key factors of surface subsidence in paste backfilling mining of thick coal seam in deep mine is a complex system engineering, which involves mining, backfilling, support, subsidence, safety, and other aspects. At present, there is no systematic research on the key factors of surface subsidence in paste backfilling mining of thick coal seam more than 6 meters in a deep mine. In this paper, field research, laboratory experiments, theoretical analysis, and other research methods are used to carry out the research about 3# coal seam under buildings in the Lu’an area. The main conclusions are as follows: through the construction of the fuzzy extension model of surface subsidence in paste backfilling mining, five types of surface subsidence are obtained, including overburden structure, roof subsidence before backfilling, nonbackfilling account, the strength of filling body, and backfilling technology. It is the key factor to control the surface subsidence; the optimization measures are given to provide a reference for the reasonable design of paste backfilling mining in other working faces. The research conclusion has a certain reference value for solving a series of problems such as coal resources under buildings, solid waste disposal, controlling strata and surface movement, improving the recovery rate of mine resources, and extending the service life of mine.