Low-frequency electronic noise is an important parameter used for the electronic and sensing applications of transistors. Here, we performed a systematic study on the low-frequency noise mechanism for both p-channel and n-channel MoTe2 field-effect transistors (FET) at different temperatures, finding that low-frequency noise for both p-type and n-type conduction in MoTe2 devices come from the variable range hopping (VRH) transport process where carrier number fluctuations (CNF) occur. This process results in the broad distribution of the waiting time of the carriers between successive hops, causing the noise to increase as the temperature decreases. Moreover, we found the noise magnitude for p-type MoTe2 FET hardly changed after exposure to the ambient conditions, whereas for n-FET, the magnitude increased by nearly one order. These noise characteristics may provide useful guidelines for developing high-performance electronics based on the emerging transition metal dichalcogenides.
This paper proposes a straightforward method for measuring micro-displacement synchronously along two orthogonal axes. A single structure consists of a pair of two-dimensional gratings and a quadrant detector aligned with a collimated laser is used to detect the micro-displacement. The crosstalk and the common-mode noise are eliminated through a two-step differential process. Experimental results demonstrate that the displacement measurement resolution can reach 40 nm with a sensitivity of 0.483 V/µm within the linear range. The accuracy obtained is 0.29% on the X-axis and 0.31% on the Y-axis within a 500 µm range. The signal-to-noise ratio is improved by 4.56 dB after differential. The simplicity and high compactness of this measurement structure make it suitable for fabrication and alignment using microfabrication processes, which show great potential in many applications such as gyroscopes, accelerators, and multi-dimensional displacement measurements.
26 May 2026 in IEEE Transactions on Instrumentation and Measurement
Time walk error significantly impacts the accuracy of distance measurements in direct time-of-flight (d-ToF) LiDAR systems. A system-level d-ToF model that comprehensively accounts for the mechanisms is established in this paper. Then, an active multi-power excitation (AMPE) strategy is proposed and verified in a silicon photomultiplier (SiPM)-based d-ToF LiDAR. Compared with conventional passive correction methods, AMPE actively injects known excitation constraints into the measurement process. It exploits the relationship between emission energy and threshold-crossing time by transmitting pulses with controlled power using a customized compensation algorithm. The core strength of this method is that it transforms the correction problem into a constrained estimation problem governed by emission control, thereby avoiding complex receiver-side timing circuitry and extensive offline calibration. A prototyped LiDAR system is developed, and experimental results demonstrate that more than a 72% reduction in walk error induced depth distortion is achieved with only 10 measurements per range point, enabling reliable 200 m operation under 60 klux ambient illumination. The proposed method establishes a novel time walk error compensation strategy, enhancing the energy efficiency and wide dynamic range of d-ToF LiDAR applications.
1 October 2026 in IEEE Transactions on Biomedical Circuits and Systems
This work presents a PET-oriented double-ring Vernier time-to-digital converter (DRVTDC) that targets the timing-quantization block required in multi-voltage-threshold (MVT) and time-over-threshold (ToT) front-end readout for time-of-flight (ToF) positron emission tomography (PET) applications. This work addresses two critical error mechanisms that limit the use of multi-stage Vernier TDCs: parallel output misalignment (POM) between quantization stages and mismatch-induced chasing error (MCE) in the Vernier arbiter array. To suppress these errors, a joint calibration scheme combining code error cancellation (CEC) and Vernier arbiter phase calibration (VAPC) is proposed. The core TDC achieves a 10.4-ps resolution with only 0.0075 mm2 core area. The implemented 7-bit coarse counter provides a dynamic range (DR) of 5.12 μs. Empowered by these techniques, the measured DNL and INL ranges are significantly improved from +3.17/-0.89 LSB and +7.0/-6.9 LSB to +0.34/-0.29 LSB and +1.15/-1.09 LSB, respectively, alongside a 26-dB enhancement in the SFDR. The core TDC consumes 1.758 mW, with a total of 5.526 mW including the PLLs.
1 January 2026 in IEEE Transactions on Circuits and Systems II: Express Briefs
This article presents a wide spectral response single-photon avalanche diode (SPAD) fabricated in a 110 nm CMOS image sensor (CIS) technology. The device integrates two vertically stacked avalanche multiplication regions comprising a shallow P++/ N-enrichment layer junction and a deeper n-type buried layer (NBL) / deep p-type buried layer (DPBL) junction, respectively. Measurement results show a peak photon detection probability (PDP) of 82% at 600 nm, with a broadband PDP exceeding 18% across 400–850 nm under an excess bias voltage of 5.0 V. At room temperature, the SPAD exhibits a moderate dark count rate (DCR) of ∼65 cps/μm². The temporal resolution corresponds to a full-width-at-half-maximum (FWHM) jitter of 69 ps at 450 nm and 110 ps at 905 nm, respectively. Owing to its vertically stacked dual-junction design, the proposed SPAD provides a compact pixel solution suitable for applications requiring operation from visible to NIR wavelengths.