Hossein Rajaei

Dr. Hossein Rajaei

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 June 2022 in Wear
Verified
Journal Article
Closed access
HRHossein Rajaei
Hossein Rajaei
CMCinzia Menapace
Cinzia Menapace
GSGiovanni Straffelini
Giovanni Straffelini
SGStefano Gialanella
Stefano Gialanella

18 January 2025 in International Journal of Fatigue
Verified
Journal Article
Open access
Lorenzo RomanelliLorenzo Romanelli
Lorenzo Romanelli
Ciro SantusCiro Santus
Ciro Santus
GMGiuseppe Macoretta
Giuseppe Macoretta
MICHELE BARSANTIMICHELE BARSANTI
MICHELE BARSANTI
BMBernardo Disma Monelli
Bernardo Disma Monelli
Matteo BenedettiMatteo Benedetti
Matteo Benedetti

10 March 2022 in Metals
Verified
Journal Article
Open access
PDF file
HRHossein Rajaei
Hossein Rajaei
Cinzia MenapaceCinzia Menapace
Cinzia Menapace
SASasan Amirabdollahian
Sasan Amirabdollahian
MPMatteo Perini
Matteo Perini
GSGiovanni Straffelini
Giovanni Straffelini
SGStefano Gialanella
Stefano Gialanella
In this paper, the refurbishing of worn-out brake discs by coating with powder via direct energy deposition (DED) is evaluated. A medium carbon steel powder was used to coat cast-iron discs. Deposition of this steel was carried out directly on the disc surface or, alternatively, after a previous deposition of a buffer layer made of stainless steel. It was seen that the use of a buffer layer ensured a good coating adhesion, despite the formation of cast microstructures at the interfaces between the disc and the two different coatings (buffer and outer layer). Coated discs were tested against two different Cu-free commercial friction materials to evaluate their tribological properties. Very similar friction coefficients, specific wear rates, and total emissions were measured for both friction materials sliding against the coated disc. These tribological data are slightly higher with respect to those obtained in the case of an uncoated disc, suggesting that improvement of the top coating composition and surface finishing is necessary in order to achieve better performances.

5 November 2023 in Lubricants
Verified
Journal Article
Open access
PDF file
HRHossein Rajaei
Hossein Rajaei
SASasan Amirabdollahian
Sasan Amirabdollahian
Cinzia MenapaceCinzia Menapace
Cinzia Menapace
GSGiovanni Straffelini
Giovanni Straffelini
SGStefano Gialanella
Stefano Gialanella
In this study, the potential of Fe3Al coating material as an environmentally friendly alternative to coatings containing critical elements for brake discs was investigated. A buffer layer of Cr–Mo steel (Ferro 55) that was about 500 µm thick was applied on a gray cast iron disc to enhance the coating quality and prevent the formation of hot cracks during solidification. The microstructural analysis of the cross-section of the coating showed that the buffer layer diffused into the Fe3Al coating, forming a combination of Fe3Al, Fe, and Fe3AlC0.5 phases. The tribological properties of the Fe3Al-coated disc were evaluated using pin-on-disc tests against two different copper-free friction materials extracted from commercial brake pads. The wear results show a coefficient of friction comparable to that of an uncoated disc (≈0.55), but with a reduction in particulate matter (PM) emissions, which decreased from 600 to 476 #/cm3. The last issue is an interesting aspect that is gaining increasing importance in view of the upcoming international standards.

7 September 2023 in Preprints.org
Verified
Preprint
Open access
PDF file
HRHossein Rajaei
Hossein Rajaei
SASasan Amirabdollahian
Sasan Amirabdollahian
Cinzia MenapaceCinzia Menapace
Cinzia Menapace
GSGiovanni Straffelini
Giovanni Straffelini
SGStefano Gialanella
Stefano Gialanella
In this study, the potential of Fe3Al coating material as an environmentally friendly alternative to coatings containing critical elements for brake discs was investigated. A buffer layer of Cr-Mo steel (Ferro 55) was applied to enhance coating quality and prevent the formation of hot cracks during solidification. Microstructural analysis of the cross-section of the coating showed that the buffer layer diffused into the Fe3Al coating, forming a combination of Fe3Al, Fe, and Fe3AlC0.5 phases. The tribological properties of the Fe3Al coating were evaluated by pin-on-disc tests using two different copper-free friction materials extracted from commercial brake pads. The wear results showed a coefficient of friction comparable to that of an uncoated disc, but with a reduction in Particulate Matter (PM) emissions, an interesting aspect that is gaining increasing importance in view of the upcoming international standards..

2 June 2025 in Journal of Alloys and Compounds
Verified
Journal Article
Open access
HRHossein Rajaei
Hossein Rajaei
AMAlberto Molinari
Alberto Molinari
IAIñigo Agote
Iñigo Agote
MLMiguel Ángel Lagos
Miguel Ángel Lagos
DFDaniele Ferrari
Daniele Ferrari
SGStefano Gialanella
Stefano Gialanella