Bump foil journal bearings (BFJBs) are widely used in the superchargers of aviation piston engines (APEs). This paper proposes a method to evaluate the operating state of superchargers by monitoring the bearing temperature. A numerical model with a repeating symmetrical structure in the axial direction is established based on a certain type of supercharger, which solves the temperature field of BFJBs with the non-isothermal Reynolds equation and energy equation. It can be used to analyze the effect of thermal expansion on lift-off speed and stop-contact speed. A new test rig and six various BFJBs were designed to check the temperature characteristics of the BFJBs with variable load and speed. By comparing the numerical results with the experimental results, it was shown that the air film temperature increased almost linearly with the increase in bearing load and speed. However, the temperature increase caused by the rotation speed was significantly greater than the load. The structural parameters of the BFJB affected the bearing support stiffness, which had a nonlinear effect on the lift-off speed and air film temperature. Therefore, the proposed method to evaluate the state of superchargers with BFJBs was effective. These thermal characteristics can be used to guide BFJB design and predict the life cycle of BFJBs.

Heavy-fuel aviation piston engines (HF-APEs) are widely used in general aviation and unmanned aerial vehicle (UAV) due to their safety and fuel economy. This paper describes a numerical and experimental study of scavenging and combustion processes on a 2-Stroke Direct Injected HF-APEs for light aircraft, with its cylinder specifically designed as cross scavenging. A 3-Dimentional transient model of in-cylinder flow and combustion process is established by the Forte platform, and the engine test system is set up. By comparing the simulation results to the experimental results, it showed that multi-ports cross scavenging can generate unbalanced aerodynamic torque in the cylinder. In the compression process, the swirl ratio (SR) gradually increases, and the peak SR reaches 15. Moreover, approximately 25% of exhaust residual gas in the cylinder is conducive to the fuel atomization and evaporation process in a high-altitude environment. When the injection timing is between −8 °CA and −16 °CA, the engine has the optimal power and economy performance at different altitudes. Finally, when the injection advance angle moves forward by 4 °CA, the maximum pressure increases by 2 MPa, with the rising rate decreasing gradually. The results have important significance for the development of the combustion system of small 2-Stroke Direct Injected HF-APEs.

Labyrinth seals are widely employed in the air system of aircraft engines since they reduce the leakages occurring between blades and shrouds, which affect the entropy generation significantly. Excessive leakage flow of the labyrinth may be reduced the efficiency and performance of the engine. This paper proposes the concept of flow-resistance-increasing vortex (FRIV) on the top of the labyrinth that is based on the flow entropy generation mechanism of the stepped labyrinth and the main flow characteristics that lead to entropy generation. A three-dimensional simulation model of the labyrinth structure was established, and the model was compared and verified with the experimental data of the reference. The relative dissipation strength and vorticity distribution of the FRIV were theoretically analyzed. It was confirmed that the dissipative intensity distribution was the same as the vorticity distribution, and the correlation coefficient was larger in the labyrinth tip region. Therefore, a parametric study was conducted on design parameters related to the FRIV, including the teeth inclined angle, tooth crest width, step inclined angle, and other parameters. The results are beneficial for the construction of a stronger FRIV to reduce the leakage. This research is of great significance for the improvement of engine efficiency and for the reduction of fuel consumption in the future.

Porous media gas bearings utilize gas as a lubricating medium to achieve non-contact support technology. Compared with traditional liquid-lubricated bearings or rolling bearings, they are more efficient and environmentally friendly. With the uniform gas film pressure of gas bearings, the rotating shaft can achieve mechanical motion with low friction, high rotational speed, and long service life. They have significant potential in improving energy efficiency and reducing carbon emissions, enabling oil-free lubrication. By eliminating the friction losses of traditional oil-lubricated bearings, porous media gas bearings can reduce the energy consumption of industrial rotating machinery by 15–25%, directly reducing fossil energy consumption, which is of great significance for promoting carbon neutrality goals. They have excellent prospects for future applications in the civil and military aviation fields. Based on the three-dimensional flow characteristics of the bearing’s fluid domain, this paper considers the influences of the transient flow field in the variable fluid domain of the gas film and the radial pressure gradient of the gas film, establishes a theoretical model and a three-dimensional simulation model for porous media gas bearings, and studies the static–dynamic pressure coupling mechanism of porous media gas bearings. Furthermore, through the trial production of bearings and performance tests, the static characteristics are verified, and the steady-state characteristics are studied through simulation, providing a basis for the application of gas bearings made from porous media materials in the civil and military aviation fields.