Recycling of waste plastics has become vital due to the threat to the environment the huge piles of those wastes represent, with research revealing High-Density Polyethylene (HDPEs) as the most dominant waste plastics. Because of their dominance and significant environmental impact, this paper reports the economic potential of recycling HDPE waste plastic into liquid fuels via pyrolysis. A risk and benefit assessment are presented to highlight whether the process has reasonable potential prior to the analysis of its corresponding finances. Aspen HYSYS simulation models were used as the basis for the analysis. From this, preliminary cost estimations for the net present value (NPV) of the process, its economic viability, were determined. It is shown that 100 kg/h of waste is not financially sustainable. Retailing the fuel product at a competitive price of £60/barrel would ultimately bankrupt the business. This is a consequence of the extremely high production cost of £198.40/barrel inducing the complete absence of profitability. Furthermore, the operating expenditure is found to be the root cause of the consequential financial decline, totalling £1.46 million per annum. The two most detrimental expenditures for the production cost of the pyrolysis oils were the wages of the skilled operating labour and higher utility fees incurred by the extreme temperature conditions. In addition, an unrealistically optimistic sale price of £300/barrel was also applied to ascertain a positive economic incentive. Even with the increased retail price, the process’ profits are negligible and further highlight the detrimental effect of the undesirably high operational expenditures, once more signifying that the process should not commence in its current state. However, executing such a project in developing countries such as Sierra Leone, Senegal, or Kenya where utilities and manpower, among other operational components, are cheaper, is believed to complement the immense opportunity underlying pyrolysis oil production regarding production quantity and quality.
7 October 2022 in Environment, Development and Sustainability
This study aims to propose a new process design, simulation, and techno-economic analysis of an integrated process plant that produces glucose and furfural from palm oil empty fruit bunches (EFB). In this work, an Aspen Plus-based simulation has been established to develop a process flow diagram of co-production of glucose and furfural along with the mass and energy balances. The plant’s economics are analyzed by calculating the fixed capital income (FCI), operating costs, and working capital. In contrast, profitability is determined using cumulative cash flow (CCF), net present value (NPV), and internal rate of return (IRR). The findings show that the production capacity of 10 kilotons per year (ktpy) of glucose and 4.96 ktpy of furfural with a purity of 98.21 and 99.54%—weight, respectively, was achieved in this study. The FCI is calculated as United States Dollar (USD) 20.80 million, while the working and operating expenses are calculated as USD 3.74 million and USD 16.93 million, respectively. This project achieves USD 7.65 million NPV with a positive IRR of 14.25% and a return on investment (ROI) of 22.06%. The present work successfully develops a profitable integrated process plant that is established with future upscaling parameters and key cost drivers. The findings provided in this work offer a platform and motivation for future research on integrated plants in the food, environment, and energy nexus with the co-location principle. Graphical Abstract
REA drying kinetics model has been widely examined for different materials and different operating conditions. Vacuum drying, due to its uniqueness, it presents a challenge for setting up the REA parameters, in particular the specification of the equilibrium activation energy value corresponding to each set of environmental condition. Here, the basic kinetic parameters derived from a convective drying run, is used while the effect of vacuum is captured by the equilibrium activation energy. Upon validation against the experimental data, REA is shown to be applicable. A comparison between the vacuum drying and the convective drying of the same material is also made. The vacuum drying at higher vacuum levels has been predicted, showing the expected behavior. It has been shown that REA is flexible and can be used in vacuum drying related design and optimization studies.
For better understanding of transport phenomena, local evaporation rate and water vapor concentration should be taken into consideration when predicting drying behavior. However, to the best of our knowledge, there is no model which explicitly represents this. Predictive modeling of combined infrared-heating and hot air drying (IR-HAD) is useful to assist in designing new dryer units and manufacturing the products with desirable quality. As the quality changes are basically local phenomena, the model should be able to capture the local evaporation rate. In this study, for the first, time, spatial reaction engineering approach (S-REA) was developed and used to describe infrared-heating drying of the food materials by using the reaction engineering approach (REA) to represent local evaporation rate. Benchmarks against the single-phase approach and the results showed that the S-REA gave high accuracy toward the experimental data (R2= 0.978–0.999). The S-REA successfully provided reasonable predictions of two-dimensional (2 D) profiles of moisture content, concentration of water vapor and temperature. This highlights the accuracy of the REA framework to describe the local evaporation rate during the infrared-heating. The REA-based predicted variables can then be applied to project the local quality parameters for quality assurance in food processing. The model is also ready to be used to audit energy demands in drying systems.
This study proposes a new process design, simulation, and techno-economic analysis of an integrated process plant that produces glucose and furfural from Malaysian empty fruit bunches (EFB). An Aspen Plus-based simulation has been established to develop a process flow diagram of co-production of glucose and furfural along with the mass and energy balances. For the production capacity of 10 kilotons per year (ktpy) of glucose and 4.96 ktpy of furfural in Malaysia, purity of 98.21 and 99.54% - weight, respectively, was achieved. The plant’s economics is analyzed by calculating the fixed capital income (FCI), operating costs, and working capital. In contrast, profitability is determined using cumulative cash flow (CCF), net present value (NPV), and internal rate of return (IRR). The FCI is calculated as Malaysian Ringgit (MYR) 81.61 million, while the working and operating expenses are calculated as MYR 11.29 million and MYR 46.92 million, respectively. This project achieves MYR 31.45 million as NPV with a positive IRR of 14.25% and return on investment (ROI) of 22.06%. As a result, a profitable integrated process plant is established with future upscaling parameters and key cost drivers. The proposed integrated process plant minimizes waste generated from the palm oil mill, resulting in a profitable and sustainable plant.