Swen Zaremba

Prof. Dr. Swen Zaremba


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
Verified
Journal Article
Open access
PDF file
NTNevine Tagscherer
Nevine Tagscherer
ABAndré Marcel Bär
André Marcel Bär
SZSwen Zaremba
Swen Zaremba
KDKlaus Drechsler
Klaus Drechsler
Large structural parts manufactured by Extrusion Additive Manufacturing (EAM) are limited by strong anisotropy due to insufficient bond formation and reduced molecular entanglement along the layer interface. To understand the correlation between process and material parameters and to enable digital modeling of EAM, the effect of different substrate temperatures and layer heights on tensile strength was investigated. A simple testing methodology for pelletized carbon fiber-filled polyamide 6 was developed. Tensile tests were performed in a full factorial Design of Experiments (DoE) to determine the tensile properties. For bulk simulation, the nominal strength and modulus were also determined based on contact width obtained by optical microscopy. The results demonstrated high anisotropy, with the maximum transverse tensile strength reaching only 27% of the corresponding longitudinal results and the transverse tensile modulus reaching only 20% of its longitudinal value. The effects of varying layer height were less significant than varying substrate temperature. The results support the hypothesis that sufficient transverse tensile strength is achieved between the extrapolated crystallization onset and melt temperature. The methodology of this study can be used as a benchmark method to qualify new thermoplastic polymers for EAM processes and to determine optimal process parameters for improved fusion bonding.

Verified
Journal Article
Open access
PDF file
MVMario Vollmer
Mario Vollmer
SZSwen Zaremba
Swen Zaremba
Pierre MertinyPierre Mertiny
Pierre Mertiny
KDKlaus Drechsler
Klaus Drechsler
Edge race-tracking is a frequently reported issue during resin transfer molding. It is caused by highly permeable channels and areas between the preform edge and cavity, which can significantly change the preform impregnation pattern. To date, information is scarce on the effect of edge race-tracking in compression resin transfer molding (CRTM). To close this gap, laboratory equipment was developed to study the CRTM preform impregnation via flow visualization experiments. The preform was thereby encapsulated in thin thermoplastic films sealing its impregnation. Film-sealed compression resin transfer molding (FS-CRTM) experiments of preforms with a small geometrical aspect ratio showed fast filling of the injection gap and a subsequent through-thickness preform impregnation. Creating an edge race-tracking channel, an additional lateral in-plane flow from the channel towards the preform center was observed, initiating soon after the injection started and caused by the spatial connection between the injection gap and the race-tracking channel. To diminish edge race-tracking, a passive flow control strategy was implemented via a split design of the upper tool to spatially isolate the injection gap from the channel and to pre-compact the preform edge. A delayed and reduced lateral race-tracking flow was observed, showing that the passive flow control strategy increases the process robustness of FS-CRTM regarding edge race-tracking effects.

8 February 2024 in Journal of Composites Science
Verified
Journal Article
Open access
PDF file
PPPhilipp Picard
Philipp Picard
Tim OsswaldTim Osswald
Tim Osswald
SZSwen Zaremba
Swen Zaremba
KDKlaus Drechsler
Klaus Drechsler
This study explores cost-effective and customized composite applications by strategically placing carbon fiber-reinforced thermoplastics in multi-material designs. The focus is on developing a model for the simultaneous processing of non-reinforced and reinforced thermoplastic layers, with the aim of identifying essential parameters to minimize insert flow and ensure desired fiber orientation and positional integrity. The analysis involves an analytical solution for two layered power-law fluids in a squeeze flow setup, aiming to model the combined flow behavior of Newtonian and pseudo-plastic fluids, highlighting the impact of the non-Newtonian nature. The behavior reveals a non-linear trend in the radial flow ratio towards the logarithmic consistency index ratio compared to a linear trend for Newtonian fluids. While a plateau regime of consistency index ratios presents challenges in flow reduction for both layers, exceeding this ratio, depending on the height ratio of the layers, enables a viable overmolding process. Therefore, attention is required when selectively placing tailored composites with long-fiber-reinforced thermoplastics or unidirectional reinforcements to avoid operating in the plateau region, which can be managed through appropriate cavity or tool designs.

20 August 2024 in Polymers
Verified
Journal Article
Open access
PDF file
AIAnna Julia Imbsweiler
Anna Julia Imbsweiler
JWJunyan Wang
Junyan Wang
RSReem Sharwalla
Reem Sharwalla
JHJulius Hoffelner
Julius Hoffelner
DCDavid Colin
David Colin
KDKlaus Drechsler
Klaus Drechsler
Using a newly developed flow test bench, several charge configurations were analyzed to quantify the influence of the charge configuration in the mold in sheet molding compound (SMC) manufacturing. A test bench was developed to satisfy the industrial needs for the incoming goods inspection as well as the need for the flow characterization of rheological models in the simulation. The test setup has a cylindrical opening for the charge placement, from where the material is pressed into a thin flow channel, forcing the material to reorient. A comparison was performed by juxtaposing the resulting compression pressure recorded during the process. The charge for this test series, placed into the cylindrical opening, has two basal configurations, one consisting of a stack of disks, and the second in a rectangular sheet rolled up into a spiral. Six charge variations were tested in total. The amount of material, the batch, the layering and the production direction of the sheet proved to have a significant influence on the necessary compression pressure. Guidelines about the recommended charge configurations could be derived for optimized production settings, such as a reduction in the compression pressure and modifications to the charge.