During the lifespan of a Polymer Electrolyte Membrane Fuel Cell (PEMFC) system, some heterogeneities between the cells constituting the stack can appear. The voltage of one particular cell in a stack may decrease because of specific aging or local malfunctioning such as drying. As a result, more heat is generated in this cell leading to an increase in its temperature and thus an additional voltage loss. This snowball effect can result in the failure of the cell. Therefore, the lifetime of a PEMFC stack can be increased by applying energy management to its cells. Notable that the output voltage of a cell is lower than a stack. Hence, a high conversion ratio converter is necessary to implement such energy management. An efficient way to increase the output voltage is to connect the output capacitors of the converters such as the boosts in series. Ensuring the converters' controllability is a key point to implement energy management. In this paper, an equalizer system is proposed to ensure the controllability of the boost converters. The balancing speed and the low number of switches are the main advantages of this system. The validity of the proposed system is verified through simulation and experiments.
17 October 2019 in IEEE Transactions on Transportation Electrification
To cope with future goal of efficiency, next generation of more electrical aircraft is likely to embed reconfigurable microgrid for the primary electrical distribution. The stability analysis of such time-varying structure is challenging. Conventional linear and nonlinear approaches failed to produce proper answers from a practical point of view. Under conditions, passivity property of each equipment is sufficient to ensure stability of the overall microgrid. But with improper passivity-based control (PBC) design, the passivity property may not be propagated. The main contribution of this article is to propose a modified IDA-PBC procedure that will ensure the passivity properties of the system regarding its electrical inputs and outputs involved in the interconnection. Thus, for electrical microgrids resulting from the interconnection of controllable equipment, input/output filters, and electrical lines, if all the equipment embed the proposed control, the whole microgrid have passive properties and the global stability of the system is ensured. Moreover, this article will also present how to achieve the proposed control with high transient and robust performances thanks to nonlinear parameters’ estimator preserving the passivity proper. Experimental validation of the proposed control in representative electrical conditions is provided.
To deal with the intermittency of renewable energy resources, hydrogen as an energy carrier is a good solution. The Polymer Electrolyte Membrane Fuel Cell (PEMFC) as a device that can directly convert hydrogen energy to electricity is an important part of this solution. However, durability and cost are two hurdles that must be overcome to enable the mass deployment of the technology. In this paper, a management system is proposed for the fuel cells that can cope with the durability issue by a suitable distribution of electrical power between cell groups. The proposed power electronics architecture is studied in this paper. A dynamical average model is developed for the proposed system. The validation of the model is verified by simulation and experimental results. Then, this model is used to prove the stability and robustness of the control method. Finally, the energy management system is assessed experimentally in three different conditions. The experimental results validate the effectiveness of the proposed topology for developing a management system with which the instability of cells can be confronted. The experimental results verify that the system can supply the load profile even during the degradation mode of one stack and while trying to cure it.
The characterization of material thermal properties at nanoscales remains a challenge even if progress was achieved in developing outstanding characterization techniques like scanning thermal microscopy (SThM). In the present work, we propose a detailed procedure based on the combined use of a SThM probe characterization and its Finite Element Method (FEM) modeling to recover in operando 3ω measurements achieved under high vacuum. This approach is based on a two-step methodology: (i) a fine description of the probe's electrical and frequency behaviors in “out of contact” mode to determine the intrinsic parameters of the SThM tip and (ii) a minimization of the free parameter of our model, i.e., the contact thermal resistance, by comparing 3ω measurements with the simulations of the probe operating “in contact mode.” Such an approach allows us to measure thermal interface resistances between the tip and the surface. We applied our methodology to three different materials with known thermal properties: Si, SiO2 bulk materials, and a gold thin film. In addition, the FEM modeling provides insights into SThM thermal probes sensitivity, as a function of probe/sample interface resistance and the contact area to measure material thermal conductivity paving the way to quantitative SThM measurements.
The share of electrical energy from renewable sources has increased considerably in recent years in an attempt to reduce greenhouse gas emissions. To mitigate the uncertainties of these sources and to balance energy production with consumption, an energy storage system (ESS) based on water electrolysis to produce hydrogen is studied. It can be applied to AC microgrids, where several renewable energy sources and several loads may be connected, which is the focus of the study. When excess electricity production is converted into hydrogen via water electrolysis, low DC voltages and high currents are applied, which needs specific power converters. The use of a three-phase, buck-type current source converter, in a single conversion stage, allows for an adjustable DC voltage to be obtained at the terminals of the electrolyzer from a three-phase AC microgrid. The voltage control is preferred to the current control in order to improve the durability of the system. The classical control of the buck-type rectifier is generally done using two loops that correspond only to the control of its output variables. The lack of control of the input variables may generate oscillations of the grid current. Our contribution in this article is to propose a new control for the buck-type rectifier that controls both the input and output variables of the converter to avoid these grid current oscillations, without the use of active damping methods. The suggested control method is based on an approach using the flatness properties of differential systems: it ensures the large-signal stability of the converter. The proposed control shows better results than the classical control, especially in oscillation mitigation and dynamic performances with respect to the rejection of disturbances caused by a load step.