Jean-Philippe Martin

Dr. Jean-Philippe Martin

LEMTA Laboratory, University of Lorraine, Vandoeuvre-lès-Nancy, France

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 August 2021 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
MAMohammad Afkar
Mohammad Afkar
RGRoghayeh Gavagsaz-Ghoachani
Roghayeh Gavagsaz-Ghoachani
MPMatheepot Phattanasak
Matheepot Phattanasak
JMJean-Philippe Martin
Jean-Philippe Martin
SPSerge Pierfederici
Serge Pierfederici
Voltage imbalance poses a challenge to photovoltaic systems. A modular structure based on a three-level boost converter is proposed to address this problem. The three-level boost converter offers advantages, such as a low current ripple and voltage stress, over a classic boost converter. These advantages offset the use of additional elements in the proposed converter circuit. Two capacitors are used in the proposed converter to enable the innovative connection between multiple sources and the three-level boost converter. The second capacitor of the first module is shared with the first capacitor of the second module. This structure is used in conjunction with a controller to balance the voltages in the system. The controller is based on an indirect sliding model, wherein the input current of each energy source and the output voltage balance are considered. The two-module system is simulated using Simulink MATLAB software. The simulation and experimental results validate the proposed system.

22 October 2018 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
RGRoghayeh Gavagsaz-Ghoachani
Roghayeh Gavagsaz-Ghoachani
MPMatheepot Phattanasak
Matheepot Phattanasak
JMJean-Philippe Martin
Jean-Philippe Martin
BNBabak Nahid-Mobarakeh
Babak Nahid-Mobarakeh
SPSerge Pierfederici
Serge Pierfederici
PRPierre Riedinger
Pierre Riedinger
This paper proposes a control method for a switching power converter. This converter is connected to a dc-link of a dc microgrid system via an LC input filter. This control method is based on a Lyapunov stability analysis; all state variables are acquired for evaluating stability analysis, including the output current for calculating the load resistance. To reduce a number of sensor counts, the input current is estimated. Moreover, loss occurrence in the converter is observed to reduce static errors of the controlled state variables, especially the output voltage. The losses are modelled as a series input voltage source observed from the dc-dc converter and a parallel current source. The latter enables us to eliminate the output current sensor. Using information from the estimated current source, a load resistance can be calculated. A Lyapunov function candidate is chosen to ensure that the system, including the observer, operates in a stable manner. Based on evaluating the time-derivative of the chosen Lyapunov function, we obtain the switching command that makes the system operate stably in each sampling cycle. In this paper, the proposed technique is applied on a boost converter. The simulation and as well experimental results validate the proposed control.

13 February 2019 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
MBMilad Bahrami
Milad Bahrami
JMJean-Philippe Martin
Jean-Philippe Martin
GMGael Maranzana
Gael Maranzana
SPSerge Pierfederici
Serge Pierfederici
MWMathieu WEBER
Mathieu WEBER
MZMajid Zandi
Majid Zandi
During the lifespan of a Polymer Electrolyte Membrane Fuel Cell (PEMFC) system, some heterogeneities between the cells constituting the stack can appear. The voltage of one particular cell in a stack may decrease because of specific aging or local malfunctioning such as drying. As a result, more heat is generated in this cell leading to an increase in its temperature and thus an additional voltage loss. This snowball effect can result in the failure of the cell. Therefore, the lifetime of a PEMFC stack can be increased by applying energy management to its cells. Notable that the output voltage of a cell is lower than a stack. Hence, a high conversion ratio converter is necessary to implement such energy management. An efficient way to increase the output voltage is to connect the output capacitors of the converters such as the boosts in series. Ensuring the converters' controllability is a key point to implement energy management. In this paper, an equalizer system is proposed to ensure the controllability of the boost converters. The balancing speed and the low number of switches are the main advantages of this system. The validity of the proposed system is verified through simulation and experiments.

9 July 2018 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
ASAhmed Eid Moussa Shahin
Ahmed Eid Moussa Shahin
JMJean-Philippe Martin
Jean-Philippe Martin
SPSerge Pierfederici
Serge Pierfederici
In this paper, a practical online open-switch fault detection method is presented. The proposed open-switch fault detection method is used to detect the open-circuited fault switch in the parallel inverters system. This method can relieve the severe effects of the over-current stress, to avoid the secondary fault to the electrical components in the parallel inverters system. This method is based on the detection of the resulting zero-sequence current, under the fault conditions. The proposed algorithm is activated by detecting the zero-sequence current between the parallel units, under the open-switch fault conditions. The sign of the resulting zero-sequence current is related to the upper or the lower open-switch fault case. The faulty phase identification relies on the analysis and the investigation of only the current measurements information of the faulty inverter. This method can get rid of the effects of the load, to obtain a reliable identification. The effectiveness of the proposed open-switch fault detection algorithm, is theoretically analyzed and validated by the simulations and the experiments.

7 May 2020 in Mathematics
Verified
Journal Article
Open access
PDF file
MBMilad Bahrami
Milad Bahrami
JMJean-Philippe Martin
Jean-Philippe Martin
GMGaël Maranzana
Gaël Maranzana
SPSerge Pierfederici
Serge Pierfederici
MWMathieu WEBER
Mathieu WEBER
MZMajid Zandi
Majid Zandi
To deal with the intermittency of renewable energy resources, hydrogen as an energy carrier is a good solution. The Polymer Electrolyte Membrane Fuel Cell (PEMFC) as a device that can directly convert hydrogen energy to electricity is an important part of this solution. However, durability and cost are two hurdles that must be overcome to enable the mass deployment of the technology. In this paper, a management system is proposed for the fuel cells that can cope with the durability issue by a suitable distribution of electrical power between cell groups. The proposed power electronics architecture is studied in this paper. A dynamical average model is developed for the proposed system. The validation of the model is verified by simulation and experimental results. Then, this model is used to prove the stability and robustness of the control method. Finally, the energy management system is assessed experimentally in three different conditions. The experimental results validate the effectiveness of the proposed topology for developing a management system with which the instability of cells can be confronted. The experimental results verify that the system can supply the load profile even during the degradation mode of one stack and while trying to cure it.

9 April 2018 in IEEE Transactions on Industry Applications
Verified
Journal Article
Closed access
ACAdrien Corne
Adrien Corne
NYNanfang Yang
Nanfang Yang
JMJean-Philippe Martin
Jean-Philippe Martin
BNBabak Nahid-Mobarakeh
Babak Nahid-Mobarakeh
SPSerge Pierfederici
Serge Pierfederici
Reduction of the manufacturing costs is one of the major concerns in the automotive industries. Removing the current sensors on the electric powertrain is a way to achieve this. In this paper, the current sensors of a stator of a wound rotor synchronous machine have been removed. In order to keep the control of the electric powertrain, the solution proposed here is to estimate the missing currents. To do so, a nonlinear observer based on the convergence of a Lyapunov candidate function has been developed for this application and compared to an extended Kalman filter (EKF). Since the parameters of the system may vary according to the operating point and the wear of the system, the robustness of the observers are tested without and with model errors and then validated on an experimental bench with a successful current sensorless control.