Genjie Yang

Mr. Genjie Yang

University of Electronic Science and Technology, Chengdu, Sichuan, China
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 December 2021 in Photonics
Verified
Journal Article
Open access
PDF file
GYGenjie Yang
Genjie Yang
DZDianli Zhou
Dianli Zhou
JLJiawen Li
Jiawen Li
JYJunsheng Yu
Junsheng Yu
The quality of active layer film is the key factor affecting the performance of perovskite solar cells. In this work, we incorporated CsPbI3 quantum dots (QDs) materials into the MAPbI3 perovskite precursor to form photoactive layer. On one hand, CsPbI3 QDs can be used as nucleation center to enhance the compactness of the perovskite film, and on the other hand, partially CsPbI3 QDs can be dissociated as anions and cations to passivate vacancy defects in the perovskite active layer. As a result, the film quality of the active layer was improved remarkably, thus exciton recombination was reduced, and carrier transfer increased accordingly. The devices based on doped-CsPbI3 QDs film had higher short circuit current, open circuit voltage and filling factor. Finally, the power conversion efficiency (PCE) was greatly enhanced from 14.85% to 17.04%. Furthermore, optimized devices also exhibited better stability. This work provides an effective strategy for the processing of high-quality perovskite films, which is of great value for the preparation and research of perovskite photoelectronic devices.

14 April 2023 in Polymers
Verified
Journal Article
Open access
PDF file
TKTianyu Kong
Tianyu Kong
GYGenjie Yang
Genjie Yang
PFPu Fan
Pu Fan
JYJunsheng Yu
Junsheng Yu
For organic solar cells (OSCs), nickel oxide (NiOx) is a potential candidate as the hole transport layer (HTL) material. However, due to the interfacial wettability mismatch, developing solution-based fabrication methods of the NiOx HTL is challenging for OSCs with inverted device structures. In this work, by using N, N-dimethylformamide (DMF) to dissolve poly(methyl methacrylate) (PMMA), the polymer is successfully incorporated into the NiOx nanoparticle (NP) dispersions to modify the solution-processable HTL of the inverted OSCs. Benefiting from the improvements of electrical and surface properties, the inverted PM6:Y6 OSCs based on the PMMA-doped NiOx NP HTL achieves an enhanced power conversion efficiency of 15.11% as well as improved performance stability in ambient conditions. The results demonstrated a viable approach to realize efficient and stable inverted OSCs by tuning the solution-processable HTL.

10 December 2020 in Micromachines
Verified
Journal Article
Open access
PDF file
ZGZhan Gao
Zhan Gao
YZYifan Zheng
Yifan Zheng
GHGuancheng Huang
Guancheng Huang
GYGenjie Yang
Genjie Yang
Xinge YuXinge Yu
Xinge Yu
JYJunsheng Yu
Junsheng Yu
Organic-inorganic hybrid perovskites have been widely used as light sensitive components for high-efficient photodetectors due to their superior optoelectronic properties. However, the unwanted crystallographic defects of perovskites typically result in high dark current, and thus limit the performance of the device. Herein, we introduce a simple route of microstructures control in MAPbI3 perovskites that associates with introducing an additive of 3,3,4,4-benzophenonetetracarboxylic dianhydridean (BPTCD) for crystallization adjustment of the perovskite film. The BPTCD additive can facilitate the formation of high-quality perovskite film with a compact and nearly pinhole-free morphology. Through characterizing the molecular interactions, it was found that the carbonyl groups in BPTCD is the key reason that promoted the nucleation and crystallization of MAPbI3. As a result, we obtained high-efficient and stable perovskite photodetectors with low dark current of 9.98 × 10−8 A at −0.5 V, an on/off ratio value of 103, and a high detectivity exceeding 1012 Jones over the visible region.

14 October 2022 in Applied Surface Science
Verified
Journal Article
Closed access
JLJiawen Li
Jiawen Li
BLBinjie Li
Binjie Li
GYGenjie Yang
Genjie Yang
Ding ZhengDing Zheng
Ding Zheng
JYJunsheng Yu
Junsheng Yu

24 December 2020 in IEEE Journal of Photovoltaics
Verified
Journal Article
Closed access
GYGenjie Yang
Genjie Yang
ZWZijun Wamg
Zijun Wamg
DZDayong Zhang
Dayong Zhang
XQXiangdong Qin
Xiangdong Qin
JHJiang Huang
Jiang Huang
JYJunsheng Yu
Junsheng Yu
A polyelectrolyte material of ethoxylated polyethylenimine (PEIE) was combined with the conventional electron transport material of [6, 6]-phenyl-C61-butyricacidmethylester (PCBM) as an electron transport layer (ETL), and high-performance perovskite photodetectors (PePDs) consisting of the PEIE:PCBM combination system as the ETL were fabricated. The PEIE:PCBM combined ETL could tune the energy barrier for invert injected hole charges between the interface of ETL and electrode. As a result, the reduced dark current and improved photoresponse of PePDs were realized. The results showed that the obtained devices possessed a high detectivity (D*) of 4.77 × 1012 Jones, which was about three folds higher than that of controlled devices with pristine PCBM ETL. Meanwhile, the PePDs exhibited excellent recovery characteristics in light/dark conversion mode. Through a series of structure, morphology, and photoelectric characterization, the detailed mechanisms for the performance improvement of PePDs are disclosed.

7 April 2021 in IEEE Journal of Photovoltaics
Verified
Journal Article
Closed access
YHYu Huang
Yu Huang
DZDayong Zhang
Dayong Zhang
MWMengge Wu
Mengge Wu
GYGenjie Yang
Genjie Yang
ZWZijun Wamg
Zijun Wamg
JYJunsheng Yu
Junsheng Yu
Perovskite solar cells (PSCs) have attracted a lot of attention due to high efficiency and low-cost fabrication processing. For planar structure PSCs, the electron transport layer (ETL) plays an important role to enhance the electron extraction capacity, device stability and balance the energy level between perovskite materials and metal electrode, which can effectively optimize the performance of PSCs. However, traditional ETL materials are not comfortable for commercialization of PSCs due to their inherent characteristics like strong aggregate, relatively low electrical conductivity, and poor ohmic contact with the metal electrodes. Here, a mixed heterojunction layer (MHL) combined an amphiphilic polymer material of poly[(9, 9-bis(3'-(N, N-dimethylamino)propyl)-2, 7-fluo-rene)-alt-2, 7-(9, 9-dioctylfluorene)] with conventional ETL materials [6, 6] phenyl C61-butyric acid methyl ester (PC 61 BM) was developed to optimize the interface characteristics between perovskite and metal electrode. Atomic force microscopy, the space charge limited current, photoluminescence measurements, and impedance spectroscopy have been measured to reveal the interface contact, electronic, and optical properties of the MHL modified PSCs device. As a result, the power conversion efficiency (PCE) of PSCs with MHL has dramatically increased from 15.17% to 18.39%. More importantly, the stability of the MHL based PSCs was improved significantly, with reduced PCE degradation (from 29% to 18%) after 160 h under ambient conditions. This research provides a simple but effective method to improve the efficiency and stability of PSCs.