TC21 titanium alloy is a new high damage-tolerant structural material for aerospace applications; its welding performance is very critical for the manufacturing of structural parts. In this research, the inertia friction welding (IFW) process of TC21 alloy was conducted, and the microstructure and mechanical properties of IFW joints were investigated. In tensile tests, specially designed tensile samples with grooves were utilized to achieve the tensile properties of IFW joints. The results show that the microhardness and tensile strength of IFW joints are higher than that of the base metal, but the plasticity of joints is worse compared with the base metal. The SEM results reveal that the weld zone has a dynamic recrystallization microstructure with uniform fine-needle phases. The microstructure evolution in the weld is the key factor that results in the change of the mechanical properties of TC21 IFW joints.
As a new highly damage-tolerant structural material, the TC21 titanium alloy has been widely used in aerospace applications. Inertial friction welding (IFW) is a form of pressure welding technology with less welding parameters and high welding joint performance, which is especially suitable for the connection of rotors of aero-compressors and engines. In this paper, inertia friction welding of TC21 titanium alloys was successfully carried out, and the microhardness, tensile properties and low cycle fatigue (LCF) behaviors of IFW joints were studied. Based on the mechanical parametric results of the tensile test, the true stress–strain curves of the IFW joint of TC21 titanium alloys are obtained by further calculation. Based on the LCF test results under different strain amplitudes, life prediction of IFW joints was investigated. The results of the LCF test show that there is no obvious cyclic hardening and cyclic softening of the IFW joints. Moreover, the fracture morphology of LCF samples under high strain amplitude (0.9%) and low strain amplitude (0.6%) was observed. The results show that the fatigue cracks initiate and propagate at multiple points in the LCF samples, and the transient fracture zone is larger under high strain amplitude. However, under low strain amplitude, a fatigue crack nucleates and propagates at a single point, and the crack propagation zone is larger.
In this paper, TC21 titanium alloy welded joints were successfully formed through inertial friction welding (IFW) processes. Microstructure evolution of IFW joints was investigated by way of different analysis methods including optical microscope (OM), scanning electron microscope(SEM), Electron Back-Scattered Diffraction(EBSD), X-Ray Diffraction(XRD), and Energy Dispersive Spectrometer(EDS). The results indicate that large-sized equiaxial β grains, original α phases, and basketweave structure existing in the BM have completely disappeared in the WZ. Instead, fine equiaxial grains sized at 20–30 μm and very fine α + β lamellar microstructure are formed in the WZ. However, as transition zones, the microstructures of the TMAZ and HAZ are also in transition state while the microstructures existing in the BM partially remain in the TMAZ and completely remain in the HAZ. In addition, second α phases are precipitated and fine α + β lamellar microstructure are formed on the original β base in the TMAZ and HAZ. XRD and EBSD results reveal that the proportion of β phase in the WZ zone decreases greatly. EDS results show that there are aggregations of stabilizing elements of β phase in the BM, but no element aggregation in the WZ. Dynamic recrystallization during the IFW process and element distribution under the rapid cooling condition after the welding process are believed to be responsible for formation of the microstructure in the weld zone of IFW joints.
TA19 titanium alloy is a novel medium-temperature, high-strength titanium alloy widely used in the aerospace industry, and its welding performance is very important for the manufacturing of structural parts. In this study, TA19 titanium alloy was connected by inertial friction welding (IFW). After welding, the microstructural and alloying elements of the IFW joints were investigated; the results showed that the microstructures of each zone of the IFW joint were different, and accumulations of the β-stable element Mo were only observed in the base metal (BM) and the heat-affected zone (HAZ). Tensile tests were performed using specially designed specimens with circular grooves to obtain the axial mechanical properties of different zones of IFW joints. The stress–strain curves and tensile fractures of the different specimens were analyzed; the results showed that the tensile strength of the welded joint increased, but the plasticity decreased from BM to WZ.