Jun Zhou

Jun Zhou


Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 March 2023 in Materials
Verified
Journal Article
Open access
PDF file
CZChunbo Zhang
Chunbo Zhang
QSQingyu Shi
Qingyu Shi
YWYihe Wang
Yihe Wang
QJQiao Junnan
Qiao Junnan
TTTianxiang Tang
Tianxiang Tang
GCGaoqiang Chen
Gaoqiang Chen
Artificial neural networks (ANNs) have been an important approach for predicting the value of flow stress, which is dependent on temperature, strain, and strain rate. However, there is still a lack of sufficient knowledge regarding what structure of ANN should be used for predicting metal flow stress. In this paper, we train an ANN for predicting flow stress of In718 alloys at high temperatures using our experimental data, and the structure of the ANN is optimized by comparing the performance of four ANNs in predicting the flow stress of In718 alloy. It is found that, as the size of the ANN increases, the ability of the ANN to retrieve the flow stress results from a training dataset is significantly enhanced; however, the ability to predict the flow stress results absent from the training does not monotonically increase with the size of the ANN. It is concluded that the ANN with one hidden layer and four nodes possesses optimized performance for predicting the flow stress of In718 alloys in this study. The reason why there exists an optimized ANN size is discussed. When the ANN size is less than the optimized size, the prediction, especially the strain dependency, falls into underfitting and fails to predict the curve. When the ANN size is less than the optimized size, the predicted flow stress curves with the temperature, strain, and strain rate will contain non-physical fluctuations, thus reducing their prediction accuracy of extrapolation. For metals similar to the In718 alloy, ANNs with very few nodes in the hidden layer are preferred rather than the large ANNs with tens or hundreds of nodes in the hidden layers.

10 May 2023 in Materials
Verified
Journal Article
Open access
PDF file
CSCao Sheng
Cao Sheng
XLXiaoguang Li
Xiaoguang Li
JLJiatao Liu
Jiatao Liu
CZChunbo Zhang
Chunbo Zhang
JZJun Zhou
Jun Zhou
LCLei Cui
Lei Cui
In this study, post-welding aging treatments were applied to a novel Ni-based superalloy GH4065A inertia friction welding (IFW) joint to improve its high-temperature properties. The effect of aging treatment on the microstructure and creep resistance of the IFW joint was systematically investigated. The results indicated that the original γ′ precipitates in the weld zone almost completely dissolved during the welding process, and fine tertiary γ′ precipitated during the subsequent cooling process. Aging treatment did not significantly change the characteristics of grain structures and primary γ′ in the IFW joint. After aging, the size of tertiary γ′ in the weld zone and secondary γ′ in the base material increased, but their morphology and volume fraction did not change evidently. After 760 °C, 5 h aging treatment, the tertiary γ′ in the weld zone of the joint grew from 12.4 nm to 17.6 nm. Correspondingly, the creep rupture time of the joint at 650 °C and 950 MPa increased from 7.51 h to 147.28 h, which is about 19.61 times higher than that of the as-welded joint. The creep rupture was more likely to occur in the base material instead of the weld zone for the IFW joint. This revealed that the creep resistance of the weld zone was significantly improved after aging due to the growth of tertiary γ′. However, increasing the aging temperature or extending the aging time promoted the growth of secondary γ′ in the base material, and meanwhile, M23C6 carbides tended to continuously precipitate at the grain boundaries of the base material. It might decrease the creep resistance of the base material.

14 March 2024 in Materials
Verified
Journal Article
Open access
PDF file
YZYongqiang Zhang
Yongqiang Zhang
PZPeng Zhao
Peng Zhao
YTYiqi Tong
Yiqi Tong
HDHonggang Dong
Honggang Dong
JZJun Zhou
Jun Zhou
Peng LiPeng Li
Peng Li
In recent years, for the structural characteristics and design requirements of the integral rotor and disc shaft of the integrated engine, the welding quality and mechanical properties of superalloy weldments have received increasing attention. In this paper, inertia friction welding (IFW) of FGH96 alloy was carried out using different welding parameters, and the homogeneous connection of FGH96 alloy hollow bars was successfully realized. The microstructure evolution, mechanical properties and fracture failure of the welded joints at room and high temperatures were investigated. The FGH96 alloy IFW joints were divided into the weld nugget zone (WNZ), the thermo-mechanically affected zone (TMAZ), the heat-affected zone (HAZ) and the base metal (BM), and there were significant differences in grain structure and distribution of the γ′ phase in each of the characteristic zones. The microhardness and tensile properties of the IFW joints were investigated, and the results showed an “M”-shaped curve in the microhardness distribution, with the lowest point of hardness observed in the HAZ. The tensile test results indicated that the fracture position moved from the BM to the WNZ with the increase in temperature, the microstructure at the fracture changed significantly and the tensile strength decreased from 1512.0 MPa at room temperature to 1201.3 MPa at 750 °C. The difference in the mechanical properties of the joints was mainly attributed to the changes in the dissolution and precipitation of the γ′ phase.

5 January 2022 in Frontiers in Materials
Verified
Journal Article
Open access
FQFeng Qin
Feng Qin
CZChunbo Zhang
Chunbo Zhang
JZJun Zhou
Jun Zhou
KXKai Xu
Kai Xu
QWQi Wang
Qi Wang
WZWenhan Zhang
Wenhan Zhang
In recent years, studying the weldability of a dissimilar metal hybrid structure, with the potential to make full use of their unique benefits, has been a research hotspot. In this article, inertia friction welding was utilized to join Φ130 forged ring of 2219 aluminum alloy with 304 stainless steel. Optical observation (OM), electron back scattering diffraction (EBSD), and scanning electron microscopy (SEM) were utilized to examine the joint microstructure in depth. Depending on the research, a significant thermal–mechanical coupling effect occurs during welding, resulting in inadequate recrystallization on aluminum-side thermo-mechanically affected zone (TMAZ) and forming zonal features. The crystal orientation and grain size of each TMAZ region reflect distinct differences. On the joint faying surface, the growth of intermetallic compounds (IMCs) is inhibited by a fast cooling rate and metallurgical bonding characteristics were found depending on the discontinuous distribution of IMCs. The average joint tensile strength can reach 161.3 MPa achieving 92.2% of 2219-O; fracture occurs on aluminum-side base metal presenting ductile fracture characteristics.

13 April 2022 in Processes
Verified
Journal Article
Open access
PDF file
LZLi Zihao
Li Zihao
SZShengsheng Zhao
Shengsheng Zhao
ZLZhijun Li
Zhijun Li
MWMeng Wang
Meng Wang
FWFayu Wu
Fayu Wu
JZJun Zhou
Jun Zhou
TC21 titanium alloy is a new high damage-tolerant structural material for aerospace applications; its welding performance is very critical for the manufacturing of structural parts. In this research, the inertia friction welding (IFW) process of TC21 alloy was conducted, and the microstructure and mechanical properties of IFW joints were investigated. In tensile tests, specially designed tensile samples with grooves were utilized to achieve the tensile properties of IFW joints. The results show that the microhardness and tensile strength of IFW joints are higher than that of the base metal, but the plasticity of joints is worse compared with the base metal. The SEM results reveal that the weld zone has a dynamic recrystallization microstructure with uniform fine-needle α phases. The microstructure evolution in the weld is the key factor that results in the change of the mechanical properties of TC21 IFW joints.

9 September 2023 in Metals
Verified
Journal Article
Open access
PDF file
JZJun Zhou
Jun Zhou
YWYanquan Wu
Yanquan Wu
CZChunbo Zhang
Chunbo Zhang
WLWu Liang
Wu Liang
RLRui Li
Rui Li
FQFeng Qin
Feng Qin
The welded joint of a dissimilar titanium alloy was obtained via inertial friction welding technology. The characteristics of the bonding interface and the microstructure of the welded joint were investigated via optical microscopy, scanning electron microscopy and electron backscattered diffraction. The results show that fine, equiaxed grains and interdiffusion bands of the elements Mo and Sn were formed in the weld zone under the high temperature and plastic deformation of the inertial friction welding. The weld zone and thermo-mechanically affected zone formed ⟨1¯21¯0⟩ α texture and ⟨111⟩ β texture, respectively.