A fiber optic interferometric sensor with an intrinsic transducer along a length of the fiber is presented for ultrasound measurements of the acoustic emission from partial discharges inside oil-filled power apparatus. The sensor is designed for high sensitivity measurements in a harsh electromagnetic field environment, with wide temperature changes and immersion in oil. It allows enough sensitivity for the application, for which the acoustic pressure is in the range of units of Pa at a frequency of 150 kHz. In addition, the accessibility to the sensing region is guaranteed by immune fiber-optic cables and the optical phase sensor output. The sensor design is a compact and rugged coil of fiber. In addition to a complete calibration, the in-situ results show that two types of partial discharges are measured through their acoustic emissions with the sensor immersed in oil.

In this paper, a multichannel instrumentation system for the location of partial discharges (PDs) in power transformers is presented. It is based on the detection of the acoustic emissions from PDs in oil with several piezoelectric (PZT) and fiber optic sensors. An acoustic detection and location approach is proposed based on a time reference given by one fiber optic sensor installed inside the tank and the times of arrival to several PZT sensors installed outside the tank (two in front of each phase windings of a three phase transformer for a typical application). The signal processing includes digital denoising techniques and time-difference lookup table-based 3-D location algorithms; these algorithms have been implemented with virtual instrumentation. The system is tested in an acoustic experimental setup and the location accuracy is evaluated. Finally, the error propagation from the times of arrival and the influence of the number of sensors and their sites in the 3-D location algorithm were analyzed.

The detection of Partial Discharges (PD) is a reliable technique to analyze the status of electrical insulation in power transformers. Phase resolved partial discharge patterns are being complemented with high frequency pulse waveform analysis, in order to identify discharge sources. In addition to this, acoustic techniques are being implemented trying to locate PD sites in large power transformers. In this work, an inductive loop sensor will be used to identify two different PD sources by means of the energy distribution of the detected waveforms. Additionally, these PD sources will be located by means of acoustic measurements with an electrical reference, through the analysis of the acoustic activity detected for each sensor individually.

A fiber-optic interferometric sensor with intrinsic transducer along a length of the fiber is presented for vibration measurements of the magnetic core inside an oil-filled power transformer. The sensor is designed for high sensitivity measurements into the harsh environment of electromagnetic fields, wide temperature change, and in oil immersing. This sensor allows enough sensitivity for the application, for which vibrations amplitudes are due to submicron displacements at frequencies of 100 Hz and its harmonics, in addition, the accessibility to the sensing region is guaranteed by low size immune fiber-optic cables as well as optical phase-based transducer/carrier of the sensor output. Thus, it is ideal for the requirements of the remote operation. The transducer size is a few mm in length, and is compact and rugged. Our results show that the vibrations of the elements constituting a power transformer are directly measured, improving the indirect techniques actually available. Finally, the measurements inside a medium power transformer at site are obtained for its application in electric plants.

A novel fiber-optic interferometric sensor is presented for vibrations measurements and analysis. In this approach, it is shown applied to the vibrations of electrical structures within power transformers. A main feature of the sensor is that an unambiguous optical phase measurement is performed using the direct detection of the interferometer output, without external modulation, for a more compact and stable implementation. High resolution of the interferometric measurement is obtained with this technique (<1 nm). The optical-fiber transducer is also specifically designed for magnifying the localized vibrations in order to modulate deeply the interferometric signal. Other advantages of the implementation for measurements within transformers are also highlighted.

Optical frequency combs (OFC) generated by electro-optic modulation of continuous-wave lasers provide broadband coherent sources with high power per line and independent control of line spacing and the number of lines. In addition to their application in spectroscopy, they offer flexible and optimized sources for the interrogation of other sensors based on wavelength change or wavelength filtering, such as fiber Bragg grating (FBG) sensors. In this paper, a dual-OFC FBG interrogation system based on a single laser and two optical-phase modulators is presented. This architecture allows for the configuration of multimode optical source parameters such as the number of modes and their position within the reflected spectrum of the FBG. A direct read-out is obtained by mapping the optical spectrum onto the radio-frequency spectrum output of the dual-comb. This interrogation scheme is proposed for measuring fast phenomena such as vibrations and ultrasounds. Results are presented for dual-comb operation under optimized control. The optical modes are mapped onto detectable tones that are multiples of 0.5 MHz around a center radiofrequency tone (40 MHz). Measurements of ultrasounds (40 kHz and 120 kHz) are demonstrated with this sensing system. Ultrasounds induce dynamic strain onto the fiber, which generates changes in the reflected Bragg wavelength and, hence, modulates the amplitude of the OFC modes within the reflected spectrum. The amplitude modulation of two counterphase tones is detected to obtain a differential measurement proportional to the ultrasound signal.