Iryna Makarava

Ms. Iryna Makarava

School of Engineering Science, Department of Separation Science, LUT University, FI-53851 Lappeenranta, Finland
orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 April 2022 in Science of The Total Environment
Verified
Journal Article
Open access
Saeed Rahimpour GolroudbarySaeed Rahimpour Golroudbary
Saeed Rahimpour Golroudbary
IMIryna Makarava
Iryna Makarava
AKAndrzej Kraslawski
Andrzej Kraslawski
EREveliina Repo
Eveliina Repo
Decarbonization of economy is intended to reduce the consumption of non-renewable energy sources and emissions from them. One of the major components of decarbonization are "green energy" technologies, e.g. wind turbines and electric vehicles. However, they themselves create new sustainability challenges, e.g. use of green energy contributes to the reduction of consumption of fossil fuels, on one hand, but at the same time it increases demand for permanent magnets containing considerable amounts of rare earth elements (REEs). This article provides the first global analysis of environmental impact of using rare earth elements in green energy technologies. The analysis was performed applying system dynamics modelling methodology integrated with life cycle assessment and geometallurgical approach. We provide evidence that an increase by 1% of green energy production causes a depletion of REEs reserves by 0.18% and increases GHG emissions in the exploitation phase by 0.90%. Our results demonstrate that between 2010 and 2020, the use of permanent magnets has resulted cumulatively in 32 billion tonnes CO2-equivalent of GHG emissions globally. It shows that new approaches to decarbonization are still needed, in order to ensure sustainability of the process. The finding highlights a need to design and implement various measures intended to increase REEs reuse, recycling (currently below 1%), limit their dematerialization, increase substitution and develop new elimination technologies. Such measures would support the development of appropriate strategies for decarbonization and environmentally sustainable development of green energy technologies.

12 June 2022 in Mineral Processing and Extractive Metallurgy Review
Verified
Journal Article
Closed access
Saeed Rahimpour GolroudbarySaeed Rahimpour Golroudbary
Saeed Rahimpour Golroudbary
IMIryna Makarava
Iryna Makarava
AKAndrzej Kraslawski
Andrzej Kraslawski
Concerns about climate change call for a careful assessment of the environmental impact of the supply chain of critical materials such as magnesium (Mg) which has a broad range of applications. Enhancing the circularity of this material is vital for ensuring its sustainable use. However, systematic analysis of the sustainability of the global production of magnesium and its circularity is still missing. We propose a novel dynamic model based on geology and processing routes to quantify the key environmental concerns across the life cycle of primary and secondary magnesium. Energy consumption, water use and related emissions are assessed for recycling including functional (recovered Mg reused in the closed-loop supply chain) and nonfunctional (recovered Mg as an element used in aluminum alloys as open-loop supply chain), as well as casting and molding. Results show a significant potential contribution of circularity of magnesium to energy (up to 31 billion GJ) and water (up to 2.7 Km3) savings, as well as the mitigation of greenhouse gas (GHG) emissions (up to 3 billion tonnes CO2 eq), globally. However, the analysis indicates that 87% of secondary magnesium comes from nonfunctional recycling. The result shows the possible increase of nonfunctional recycling of magnesium from 612 kt in 2020 to 1 mt in 2050, and the growth of functional recycling of magnesium from 96 kt in 2020 to 161 kt in 2050. The finding highlights the necessity for improving supply chain policies of Mg through technological developments and operational changes to ensure its sustainable circular economy.

12 August 2022 in Materials
Verified
Journal Article
Open access
PDF file
IMIryna Makarava
Iryna Makarava
MEMohammadamin Esmaeili
Mohammadamin Esmaeili
WQwqw qwe
wqw qwe
Leonardo PelcastreLeonardo Pelcastre
Leonardo Pelcastre
Jacek RylJacek Ryl
Jacek Ryl
Eveliina RepoEveliina Repo
Eveliina Repo
The Ni-TiO2 and Ni-CeO2 composite coatings with varying hydrophilic/hydrophobic characteristics were fabricated by the electrodeposition method from a tartrate electrolyte at ambient temperature. To meet the requirements of tight regulation by the European Chemicals Agency classifying H3BO3 as a substance of very high concern, Rochelle salt was utilized as a buffer solution instead. The novelty of this study was to implement a simple one-step galvanostatic electrodeposition from the low-temperature electrolyte based on a greener buffer compared to traditionally used, aiming to obtain new types of soft-matrix Ni, Ni-CeO2, and Ni-TiO2 coatings onto steel or copper substrates. The surface characteristics of electrodeposited nickel composites were evaluated by SEM, EDS, surface contact angle measurements, and XPS. Physiochemical properties of pure Ni, Ni-CeO2, and Ni-TiO2 composites, namely, wear resistance, microhardness, microroughness, and photocatalytic activity, were studied. Potentiodynamic polarization, EIS, and ICP-MS analyses were employed to study the long-term corrosion behavior of coatings in a 0.5 M NaCl solution. Superior photocatalytic degradation of methylene blue, 96.2% after 6 h of illumination, was achieved in the case of Ni-TiO2 composite, while no substantial change in the photocatalytic behavior of the Ni-CeO2 compared to pure Ni was observed. Both composites demonstrated higher hardness and wear resistance than pure Ni. This study investigates the feasibility of utilizing TiO2 as a photocatalytic hydrophilicity promoter in the fabrication of composite coatings for various applications.

13 February 2022 in Minerals Engineering
Verified
Journal Article
Open access
IMIryna Makarava
Iryna Makarava
AKAliaksandr Kasach
Aliaksandr Kasach
WQwqw qwe
wqw qwe
IKIrina Kurilo
Irina Kurilo
MLMarkku Laatikainen
Markku Laatikainen
EREveliina Repo
Eveliina Repo

15 June 2023 in Minerals Engineering
Verified
Journal Article
Open access
IMIryna Makarava
Iryna Makarava
MEMohammadamin Esmaeili
Mohammadamin Esmaeili
SPSimo Pöntynen
Simo Pöntynen
VKVitalii Kavun
Vitalii Kavun
MBMohammad Reza Bilesan
Mohammad Reza Bilesan
EREveliina Repo
Eveliina Repo

22 December 2023 in ECS Meeting Abstracts
Verified
Journal Article
Closed access
IMIryna Makarava
Iryna Makarava
ZWZulin Wang
Zulin Wang
Benjamin WilsonBenjamin Wilson
Benjamin Wilson
KYKirsi Yliniemi
Kirsi Yliniemi
MLMari Lundström
Mari Lundström
Cobalt is a highly important metal that is widely used in lithium-ion batteries, cemented carbide, magnetic materials, chemical, and medical industries. The current global cobalt reserves (in total around 6.9 million tons) are unevenly distributed mainly between the Democratic Republic of Congo (48%) and Australia (21%) [1]. One of the main sources of cobalt is nickel production where Co is as a byproduct. Nevertheless, research related to cobalt extraction from both primary or secondary resources must be accelerated to address the current imbalance between supply and demand, that has resulted in cobalt being classified as highly critical by the EU [2]. Currently, primary and secondary raw materials are refined using pyro-hydrometallurgical or hydrometallurgical processing routes, followed by e.g. cobalt crystallization, or electrowinning. Battery grade cobalt salts can be further subjected for calcination to form battery grade oxides. In the current study, we investigate a novel approach of electrifying metallurgy - attempting for direct electrochemical cobalt recovery as cobalt oxide from a hydrometallurgical chloride based process solution. Potentiostatic electrolysis was performed in synthetic cobalt chloride solution, mimicking the industrial concentrations. SEM and EDX were used for microstructural characterization and determination of sample compositions, respectively. Cyclic voltammetry (CV) was also carried out to understand the anodic behavior of cobalt on the Pt electrode. CV studies suggested the formation of different cobalt-containing phases and the obtained precipitates in potentiostatic experiments were identified as Co3O4 and CoOOH. However, the precipitate composition was strongly dependent on the conditions of electrolysis, such as potential, temperature, and pH. At the highest studied potential (1150 mV vs. Ag/AgCl) the precipitate obtained had a saturated black color indicating desired formation of Co3O4, while at lower potentials the brown colour indicated dominance of other phases. The microstructure of the electrodes due to different potentials was investigated by SEM, indicating also morphology changes as a function of recovery potential. EDX analysis suggested that the precipitates recovered included not only cobalt and oxygen but also traces of chloride ions. Overall, this study highlights the possibility of cobalt recovery in oxide form in a chloride medium as an alternative method for the recovery of cobalt from industrial process solutions. The proposed approach can be suggested as an alternative to the traditional process of crystallization or electrowinning. In addition, cobalt obtained in a form of oxide is an important class of materials characterized by good electrochemical, catalytic, and optical properties and can be used as a final product in a variety of applications if quality requirements can be achieved. Acknowledgment The ENICON project (https://enicon-horizon.eu/) has received funding from the European Union’s Framework Program for Research and Innovation Horizon Europe under Grant Agreement No. 101058124 References Rahimpour Golroudbary, S.; Farfan, J.; Lohrmann, A.; Kraslawski, A. Environmental Benefits of Circular Economy Approach to Use of Cobalt. Global Environmental Change (2022) 76, doi:10.1016/j.gloenvcha.2022.102568. Blengini, G.A.; EL Latunussa, C.; Eynard, U.; Torres de Matos, C.; Wittmer, D.; Georgitzikis, K.; Pavel, C.; Carrara, S.; Mancini, L.; Unguru, M.; et al. Study on the EU’s List of Critical Raw Materials (2020) Final Report., doi:10.2873/904613.