The purpose of this review is to put previous research findings on acetylated wood and the fabrication of veneer-based products in a common context. The first research on wood acetylation was already conducted in the 1920s using wood meal, whereas relevant research on veneer acetylation was published nearly two decades later, during the 1940s. In the years that followed, a great deal of research has been done on both solid wood and composite acetylation. Developments in the 1990s and early 2000s resulted in the creation of commercial products. Nowadays, wood is becoming increasingly popular in construction. Therefore, high-performance materials with high dimensional stability and durability are required. Veneers are thereby of particular relevance because of their propensity to absorb chemicals into even tough-to-treat wood species. However, acetylation alters the bonding properties of wood, which is important for the manufacture of engineered veneer products, especially in load-bearing construction. A large amount of research is now being conducted on the acetylation of veneer, and acetylated veneer products are anticipated in the near future. This study covers the fundamentals of bonding but focuses specifically on veneer acetylation and its fabrication to engineered veneer-based products. The influencing factors of acetylation on bonding are also discussed.
Acetylation with acetic anhydride is well known to improve the dimensional stability and durability of wood. Veneer is appealing for acetylation because of its thin thickness, which supports a complete and even impregnation of difficult-to-treat wood species, such as beech (Fagus sylvatica L.). Unlike resin-based veneer impregnation, acetylated veneer does not require any additional curing. As a result, veneer properties are already altered prior to bonding. The compression thickness reduction in acetylated beech veneer during the manufacturing of laminated veneer lumber (LVL) utilizing 1, 3, and 6 MPa at 150 °C for 30 min is investigated in this study. The results show that acetylated beech veneer is considerably less compressible than the references. Moreover, the density of acetylated LVL at low pressure (1 MPa) is similar to the one of references, even though the compressibility is much lower. This is due to the added acetyl groups after acetylation. The reduction in compressibility is most likely caused due to a decrease in moisture content (MC) and its accompanied mechanisms.
21 September 2022 in Wood Material Science & Engineering
This study demonstrates acetylation with acetic anhydride, one of the few industrial wood modification techniques on the market, to increase the dimensional stability and durability of laminated veneer lumber (LVL) made from beech wood (Fagus sylvatica L.). After being acetylated, veneers were hot-bonded to LVL using phenol-formaldehyde resin (PF) or phenol-resorcinol-formaldehyde resin (PRF). The bonding performance (bonding shear strength (BSS) and wood failure (WF)) was tested under the following three conditions: 20°C and 65% RH, water immersion, and rigorous boiling-drying-boiling. Additionally, using the same specimen sizes on a second sample set, the moisture content (MC) and dimensional stability were determined. Results indicate that the PRF resin provided the strongest bonding performance on acetylated LVL and references. Additionally, acetylated LVL outperformed unmodified references in moist settings, particularly the BSS after boiling in water.
8 May 2023 in European Journal of Wood and Wood Products
The overall aim of this study was to investigate the durability of acetylated beech (Fagus sylvatica L.) laminated veneer lumber (LVL) against wood-destroying basidiomycetes. The secondary objective was to test whether the specimen size affects the mass loss and durability assessment of wood-material under test. The durability test was based on the pre-standard prEN 113-3. Six materials (acetylated beech LVL, untreated beech LVL, beech solid wood, pine sapwood (Pinus sylvestris L.), larch (Larix decidua Mill.) 3-layer slab, larch solid wood) were tested using three specimen geometry designs (50 × 25 × 15 mm3 as well as 50 × 50 × 19 mm3 with and without sealed edges) against Coniophora puteana, Rhodonia placenta, Gloeophyllum trabeum, Trametes versicolor, and Pleurotus ostreatus. The durability assessment was made using the arithmetic mean and median percentage mass loss (ML), the relative ML (x-values), and the decay susceptibility index (DSI). It was found that mass loss was affected by the test fungus, the material, and the specimen size and design, with the latter being the most essential factor in this study. In addition, the assessment parameter had a significant effect on the durability classification. Furthermore, small differences in ML resulted in different durability classes (DC) in some cases, whereas large differences in ML did not. However, acetylated beech LVL was always considerably durable (DC 1) against all tested fungi independent of the specimen design and durability assessment method.
24 June 2023 in European Journal of Wood and Wood Products
Experiments on finger-jointing acetylated beech (Fagus sylvatica L.) laminated veneer lumber (LVL) have been made. The specimens were examined on its wet tensile shear strength (TSS) using three adhesives, including phenol resorcinol formaldehyde (PRF), one-component polyurethane (PUR) (without primer), and melamine urea formaldehyde (MUF). Contact angles (CA) of uncured and drop-applied MUF, PRF, and PUR adhesives on freshly cut finger-joints were evaluated. Surface roughness was measured using a laser-scanning-microscope (LSM). Results showed that PRF bonded acetylated specimens had highest wet TSS, followed by specimens with PUR bonding. MUF performed poorly, which was most likely caused by its inadequate water resistance and changes in chemical reactions due to remaining acetic acid. Acetylated finger-joints had a topography similar to untreated joints. Moreover, CA were just barely lower for MUF and PRF on acetylated wood than on untreated references.
Acetylation of wood with acetic anhydride reduces the wood–moisture interaction, improves the dimensional stability and resistance against biodegradation. However, the adhesive bonding is affected by the modification, which is crucial to manufacture engineered wood products, such as laminated veneer lumber (LVL). In this study we report the bonding of 8-layered acetylated beech (Fagus sylvatica L.) LVL boards to 2-layered LVL beams. The beams were glued together at room temperature adding three common load-bearing construction adhesives: melamine–urea–formaldehyde (MUF), phenol–resorcinol–formaldehyde (PRF), and one-component polyurethane (PUR). The bonding performance was tested by assessing its dry and wet tensile shear strength (TSS) and wood failure percentage (WF). Also evaluated were the material's density and moisture content (MC). The surface was characterized prior to bonding by its pH, roughness, and contact angle (CA). The adhesive penetration was observed by fluorescence microscopy. Aside from MUF, applying PRF and PUR adhesives achieved good bonding performance on acetylated LVL and references. Acetylated LVL displayed a more hydrophobic behaviour, a higher pH, a somewhat smoother surface, and an increased density.