Recent studies showed treatments with sorbitol and citric acid (SorCA) to significantly improve the dimensional stability and biological durability of wood. The industrialization of this process requires a quality control (QC) method to determine if the fixated chemicals are homogenously distributed within the piece of wood, which is essential for uniform material performance. Therefore, the objective of this work was to evaluate the use of common electromagnetic radiation-based methods to determine the degree of modification in SorCA-treated wood. Both Fourier transform infrared (FTIR) spectroscopy and near-infrared (NIR) spectroscopy have been used to create rough calibrations for the weight percent gain (WPG) prediction models. The FTIR measurements resulted in a high linear correlation between the band area ratio (BAR) and the WPG (R2 = 0.93). Additionally, a partial least square (PLS) regression of NIR spectroscopic data resulted in a model with a high prediction power (R2 = 0.83). Furthermore, X-ray density profiling emerged as a simple alternative for the QC by showing a gradient of modification chemicals inside the sample and differences in chemical uptake between earlywood and latewood. Overall, it can be concluded that the results from FTIR, NIR and X-ray densitometry can serve as indicators of impregnation chemical distribution in SorCA-modified wood.
Acetylation with acetic anhydride is well known to improve the dimensional stability and durability of wood. Veneer is appealing for acetylation because of its thin thickness, which supports a complete and even impregnation of difficult-to-treat wood species, such as beech (Fagus sylvatica L.). Unlike resin-based veneer impregnation, acetylated veneer does not require any additional curing. As a result, veneer properties are already altered prior to bonding. The compression thickness reduction in acetylated beech veneer during the manufacturing of laminated veneer lumber (LVL) utilizing 1, 3, and 6 MPa at 150 °C for 30 min is investigated in this study. The results show that acetylated beech veneer is considerably less compressible than the references. Moreover, the density of acetylated LVL at low pressure (1 MPa) is similar to the one of references, even though the compressibility is much lower. This is due to the added acetyl groups after acetylation. The reduction in compressibility is most likely caused due to a decrease in moisture content (MC) and its accompanied mechanisms.
The present study aimed to evaluate the effect of citric acid on the properties of solid pine wood, which were submitted to thermomechanical treatment. A preliminary test was performed in a previous study to evaluate the influence of different temperatures of pressing and concentrations of citric acid on the physical properties of wood. After choosing the best treatments (170 °C and 5% and 10% of citric acid), the effect of these on the chemical properties (SEM, FTIR and pH); on the density profile using an X-ray microtomography and on the resistance to aging through an abrasion test were evaluated. The result of the chemical analysis showed an increase of the presence of ester functional groups, as well as better coverage and higher acidity of the surface. The density profile technique allowed us to observe the formation of peaks of density on the surface where the acid was applied. Lastly, it was also possible to verify an increase in the resistance to abrasions because of the application of citric acid.
In the development of new materials, the focus nowadays is increasingly on their relevance with regard to lightweight construction or environmental compatibility. The idea of a lightweight sandwich panel was inspired by an increasing number of cosmetic accessories that use the fibers of the loofah plant, a rapidly renewable, light, fibrous raw material. The aim of the study was to develop a fiber composite panel based on the fibers of the loofah plant (Luffa cylindrica) as core material and wooden veneer as the skin layer to be used in areas of lead construction. Three different panel variations were produced for the tests, with a fiber–adhesive ratio between 1:1.05, 1:0.8, and 1:0.5. The mechanical strength (flexural strength and internal bond) and the physical properties (density and thickness swelling) were determined as a function of the fiber–adhesive composition. The results show that the flexural strength increased by approx. 400% and the thickness swelling was reduced by 10% with increasing adhesive quantity.
28 January 2025 in Wood Material Science & Engineering
Flame retardants and other additives can reduce the performance of adhesives used to produce wood-based panels such as particleboards (PB). Basalt reinforcement was evaluated to compensate for the loss of bending strength to allow the panels to be used in the construction sector. A basalt grid with a grammage of 200 g m−2 was used to reinforce PB containing 15 m% nitrogen-phosphate based flame retardant. The modulus of rupture (MOR) and modulus of elasticity (MOE) of the reinforced panels were higher (69% and 24%, respectively) than those of corresponding reference panels. The thermal analysis revealed that the addition of the flame retardant could result in the PB being upgraded to Euroclass B with a reduced crack formation, as identified via 3D-microscopy. Consequently, the use of basalt grid as a reinforcement material could be a way to reinforce panels that contain strength-reducing additives.