This research presents an analysis of the five-position angle in both single-axis (one-axis tracking) and dual-axis (two-axis tracking) solar tracking systems. The study compares these tracking systems, where four solar panels move simultaneously, with a fixed solar panel system. The findings revealed that the five-position angle Sun-tracking technique resulted in lower energy consumption by the tracking mechanism than in the case of an all-time solar tracking system. The key component of the implemented system is a light-dependent resistor (LDR) sensor for controlling the motion of the motor for five positions on the vertical axis and horizontal axis, processed by a microcontroller to ensure the necessary solar tracking always moves in a perpendicular direction. According to the results, the voltage, current, and power increased with both one-axis and two-axis tracking compared to those of the fixed solar panel system under the same conditions. However, when evaluating the total energy with numerical integration methods, one-axis and two-axis provided 183.12 Wh and 199.79 Wh, respectively. Consequently, the energy production of the one-axis tracking system and the one-axis tracking system was found to be 16.71% and 24.97%, respectively, when compared to the fixed-axis system. Thus, the five-position angles of the sun-tracking technique resulted in lower energy consumption than is the case of an all-time solar tracking system.

The lifetime of a cast-resin transformer mainly depends on the condition of insulation material. Partial discharge (PD) is an important reason for insulation deterioration in cast-resin transformers. Identifying the position of PD is very necessary for damage assessment while the transformer is still operating, and the transformer is covered by housing. This paper proposes the investigation of a cast-resin transformer using an AE sensor and HFCT sensor to specify the precise source of PD. In this study, four AE sensors were used to find PD sources, and the high-frequency current transducer (HFCT) technique was used to identify the PD source and the criteria level. The experiment, in the first two parts, identified the possibility of PD, which includes the position of PD. The final part of the experiment verified the position of the PD source of a cast-resin transformer and confirmed the inspection results. AE and HFCT sensors can be used to detect the location of PD sources, confirming the position of the PD source by sensor detection. In addition, the evident partial discharge picture on the insulator surface of high voltage side. The process successfully and accurately identifies and locates the PD source.

This study used the Area Elimination Method (AEM) of transformer design with transformer characteristic simulation. The multidimensional variable of physical parameters such as magnetic density, current density, voltage and coil turn was performed. This method was used in designing the 8000 kVA 22,000–3300/1905 V oil-type large distribution transformer. The result from a design found that the objective function tries to reduce the material to be used, and less core steel, less conductors, less transformer oil or less transformer tanks may cause an increasing load loss or increasing temperature rise, but we have calculated the temperature in the winding and design the radiator fins at the same time. After designing the transformer with AEM and it being manufactured in the production process, the transformer was tested according to IEC standards. It was confirmed that the power loss tests with no load yielded lower power loss than the standard value. In addition, the transformer passed the satisfaction test and the results of this design were built and tested with IEC 60076 standards. The information from the design using the Area Elimination Method could be a guarantee of standardized accuracy for oil distribution transformers. This also saves time and increases design efficiency for transformer designers.

This research has developed a process for producing ZnO thin film from DEZn deposited onto a PET substrate with low-pressure, high-frequency Ar + O₂ plasma using a chemical vapor deposition technique. The aim is to study the film production conditions that affect electrical properties, optical properties, and thin film surfaces. This work highlights the use of plasma energy produced from a mixture of gases between Ar + O₂. Plasma production is stimulated by an RF power supply to deliver high chemical energy and push ZnO atoms from the cathode inside the reactor onto the substrate through surface chemical reactions. The results showed that increasing the RF power in plasma production affected the chemical reactions on the substrate surface of film formations. Film preparation at an RF power of 300 W will result in the thickest films. The film has a continuous columnar formation, and the surface has a granular structure. This results in the lowest electrical resistivity of 1.8 × 10⁻⁴ Ω. In addition, when fabricated into a DSSC device, the device tested the PCE value and showed the highest value at 5.68%. The reason is due to the very rough surface nature of the ZnO film, which increases the scattering and storage of sunlight, making cells more efficient. Therefore, the benefit of this research is that it will be a highly efficient prototype of thin film production technology using a chemical process that reduces production costs and can be used in the industrial development of solar cells.

This research has developed a process for producing ZnO thin film from DEZn deposited onto a PET substrate with low-pressure, high-frequency Ar + O2 plasma using a chemical vapor deposition technique. The aim is to study the film production conditions that affect electrical properties, optical properties, and thin film surfaces. This work highlights the use of plasma energy produced from a mixture of gases between Ar + O2. Plasma production is stimulated with an RF power supply to deliver high chemical energy and push ZnO atoms from the cathode inside the reactor onto the substrate through surface chemical reactions. The results showed that increasing the RF power in plasma production affected the chemical reactions on the substrate surface of film formation. The film preparation at RF power 300 W will give the thickest films. The film has a continuous columnar formation, and the surface has a granular structure. This results in the lowest electrical resistivity of 1.8 x 10-4 Ω-cm. In addition, when fabricated into a DSSC device, the device tested the PCE value and showed the highest value at 5.68%. This is due to the very rough surface nature of the ZnO film, which increases the scattering and storage of sunlight, making cells more efficient. Therefore, the benefit of this research is that it will be a highly efficient prototype of thin film production technology using a chemical process that reduces production costs and can be used in the industrial development of solar cells.