The development of artificial stone from the agglutination of polymeric resin using industrial wastes can be a viable alternative from a technical, economic, and sustainable point of view. The main objective of the present work was to evaluate the physical, mechanical, and structural properties of artificial stones based on quartzite waste added into a synthetic, epoxy, or biodegradable polyurethane polymer matrix. Artificial stone plates were produced through the vacuum vibration and compression method, using 85 wt% of quartzite waste. The material was manufactured under the following conditions: 3 MPa compaction pressure and 90 and 80 °C curing temperature. The samples were characterized to evaluate physical and mechanical parameters and microstructure properties. As a result, the artificial stone plates developed obtained ≤0.16% water absorption, ≤0.38% porosity, and 26.96 and 10.7 MPa flexural strength (epoxy and polyurethane resin, respectively). A wear test established both artificial quartzite stone with epoxy resin (AS-EP) and vegetable polyurethane resin (AS-PU) high traffic materials. Hard body impact resistance classified AS-EP as a low height material and AS-PU as a very high height material. The petrographic slides analysis revealed that AS-EP has the best load distribution. We concluded the feasibility of manufacturing artificial stone, which would minimize the environmental impacts that would be caused by this waste disposal. We concluded that the production of artificial rock shows the potential and that it also helps to reduce environmental impacts.
The objective of this research was to produce artificial stone plates based on granite and mirror wastes and epoxy matrix, by vibration, compression, and vacuum and to characterize them. Plates were manufactured with 15%wt epoxy resin and 85% of aggregates in the proportion of 1/3 of granite waste from Ocre Itabira gray granite and 2/3 of mirror waste. The apparent density, water absorption, and apparent porosity values were 2.22 g/cm3, 0.11%, and 0.25%, respectively, the flexural strength was 34.36 MPa, abrasive wear after a 1000m track was 2.28mm and the breaking height in the impact resistance test was 0.45m. In addition, the stone was resistant to several staining agents. Therefore, the technical viability of the material developed was verified, with results compatible with studies already carried out in the area, making it possible to apply it as coatings and countertops in civil construction.
1 February 2024 in Revista de Gestão Social e Ambiental
Objective: This work aims to evaluate the physical and alterability properties such as resistance to staining and chemical attack of two natural stones (Siena White and White Marble) and two artificial agglomerated stones (Aldan White and Galaxy White), using Brazilian technical standards as methodology. ABNT NBR 15845 (2015), NBR 16596 (2017) and NBR 10545 (2017). Theoretical Framework: Ornamental stones, such as granite, marble and quartzite, are valued in construction and decoration for their durability and natural beauty. Artificial agglomerated stones are industrially produced to imitate the appearance of natural stones, offering additional advantages such as greater uniformity and resistance. Both options have their various aesthetic and functional applications. Method: Ten specimens measuring 60 x 60 x 20 mm were used for each material. Apparent density, apparent porosity and water absorption tests were carried out. To determine resistance to chemical attack, ABNT NBR 16596 (2017) was used, where the stones were exposed to a variety of chemical agents. The determination of stain resistance was carried out according to the ABNT NBR 10545-14 (2017) standard in an adapted form. The samples were exposed for 24 hours to penetrating agents and household products. Subsequently, the material was classified according to the ease of removing stains, after the cleaning steps described in the standard. Results and Discussion: The results showed that natural stones and artificial agglomerates were satisfactory in meeting the requirements of the ABNT NBR 15844 (2015) standard, as the lower porosity and reduced water absorption generally make these materials more durable and easier to maintain, especially in environments where the Exposure to moisture and liquids is an important factor, such as in kitchens and bathrooms. Research Implications: Evaluate the physical indices, staining and chemical attack of natural stones and artificial agglomerated stones produced by the industry. Originality/Value: Carry out tests on natural stones and artificial agglomerates in materials sold in industry and certify their technological characteristics through tests established by Brazilian standards.
13 March 2024 in Revista de Gestão Social e Ambiental
Theoretical framework: Brazil is one of the world's largest producers of ornamental stones, and is therefore the richest country in granite diversity in the world. Improvements in processing and production techniques have been developed over the years to add value to the final product. The resistance of stones is a preponderant factor for their application in certain environments. Some stone industries try to improve the resistance of the material by resining or reinforcing (resin plus fiberglass mesh) on their material. Method/project/approach: the work studied the behavior of resined and reinforced stones (resin plus fiberglass mesh). three-point flexural strength tests were carried out on pegmatite stones and quartzites. They were divided into groups with just resin and others with resin plus fiberglass mesh. Results and conclusion: The results showed that in the group of Pegmatite stones it was possible to obtain a gain of up to 44% in material resistance when resined and reinforced. However, the Quartzites did not have a significant gain, in some cases they obtained a lower value when reinforced. Only one of the quartzites achieved a 14% gain in resistance. Therefore, it is necessary to carry out a preliminary study with laboratory tests before resining and reinforcing the ornamental stones for sold. Research implications: Compare the three-point flexural strength between samples of pegmatic and quartzite stones and evaluate the resistance of reinforced (resin plus fiberglass mesh) and resin (resin) stones. Originality/value: analyze the influence of resin and fiberglass mesh on the three-point flexural strength of ornamental stones.