This paper proposed implementing a water and air monitoring system using sensor development and a LoRa Network. To transmit data, a self-made PCB board integrates the terminal sensors with Renesas RX64M MCU and LoRa. There are 16 monitoring point stations for the media experiment. The sensors were used to measure the water and air parameters such as PM_2.5, CO₂, DO concentration, pH level, temperature, and humidity. In addition, the Grafana system was implemented to present the status and variation in the monitoring parameters in the environmental area. To evaluate the monitoring system, we also collected public information provided by the environmental protection department of the Taiwan government at the same monitoring point for comparison.

We report the fabrication of a flexible network of multiwall carbon nanotubes (MWCNTs) known as buckypaper (BP) for thermoelectric (TE) applications. A thermal evaporation method was used to deposit TE metal alloys onto the BP. The TE properties were improved primarily by increasing the Seebeck coefficient values (50 and 75 μV/K) and the electrical conductivity by approximately 10 000 S/m. High‐temperature resistivity studies were performed to confirm the semiconductivity of buckypaper. Variations in resistivity were observed to be the result of the metal alloys coated on the BP surface. We also demonstrated that a substantial increase in the Seebeck coefficient values can be obtained by connecting 3 and 5 layers of metal‐deposited BP in series, thereby enhancing the TE efficiency of MWCNT‐based BP for application in thermoelectric devices.

We compared the hydrogen uptake weight percentages (wt.%) of different carbonized materials, before and after modification, for their application in hydrogen storage at room temperature. The Sievert's method [T.P. Blach, E. Mac, A. Gray, J. Alloys Compd. 446-447, 692 (2007)] was used to measure hydrogen uptake values on: (1) Taiwan bamboo charcoal (TBC), (2) white charcoal (WC), (3) single-walled carbon nanotubes (SWCNTs) bought from CBT Inc. and (4) homemade multi-walled carbon nanotubes (MWCNTs) grown on TBC. Modified samples were coated with a metal catalyst by dipping in KOH solutions of different concentrations and then activated in a high temperature oven (800 °C) under the atmospheric pressure of inert gas. The results showed that unmodified SWCNTs had superior uptake but that Taiwan bamboo charcoal, after modification, showed enhanced uptake comparable to the SWCNTs. Due to TBC's low cost and high mass production rate, they will be the key candidate for future hydrogen storage applications.

This study investigates the impact of plasma gradient modification and gradient illumination on the optoelectronic properties of buckypaper (BP), a flexible and large-scale material composed of multi-walled carbon nanotubes (MWCNTs). The BP samples were subjected to argon ion plasma treatment at varying power levels and durations, thereby creating different carrier concentration gradients on the surface. The photovoltage and photocurrent responses of the samples were then measured under uniform full illumination and gradient illumination conditions. The findings revealed that both plasma gradient modification and gradient illumination significantly enhanced the optoelectronic performance of BP. Notably, the combined application of these two methods yielded superior results compared to the application of either method alone. Specifically, the optimal plasma power for improving BP was found to be 20 W. Under conditions of plasma gradient modification and gradient illumination, a photovoltage of 267.76 μV was generated, which represents a 21.44 times increase, and a photocurrent of 15.69 μA, reflecting a 32.69 times enhancement. The mechanism underlying this optoelectronic effect can be attributed to the presence of π-bonds in the carbon atoms. These π-bonds are excited by photons, resulting in the generation of small voltages and currents. This study underscores the potential of BP as an optoelectronic material and introduces a novel approach to enhance its optoelectronic properties through plasma gradient modification and gradient illumination.

This study investigates the impact of plasma gradient modification and gradient illumination on the optoelectronic properties of buckypaper (BP), a flexible and large-scale material composed of multi-walled carbon nanotubes (MWCNTs). The BP samples were subjected to argon ion plasma treatment at varying power levels and durations, thereby creating different carrier concentration gradients on the surface. The photovoltage and photocurrent responses of the samples were then measured under uniform full illumination and gradient illumination conditions. The findings revealed that both plasma gradient modification and gradient illumination significantly enhanced the optoelectronic performance of BP. Notably, the combined application of these two methods yielded superior results compared to the application of either method alone. Specifically, the optimal plasma power for improving BP was found to be 20W. Under conditions of plasma gradient modification and gradient illumination, a photovoltage of 267.76 μV was generated, which represents a 21.44 times increase, and a photocurrent of 15.69 μA, reflecting a 32.69 times enhancement. The mechanism underlying this optoelectronic effect can be attributed to the presence of π-bonds in the carbon atoms. These π-bonds are excited by photons, resulting in the generation of small voltages and currents. This study underscores the potential of BP as an optoelectronic material and introduces a novel approach to enhance its optoelectronic properties through plasma gradient modification and gradient illumination.