Small fault area in coal mine has great risk of coal and gas outburst. However, the damage effect of small faults on coal pore structure still lacks systematic research. Taking a small reverse fault under Pingmei No. 2 mine as an example, this paper collects the hanging wall coal samples within 5 m from the fault plane and the coal samples 50 m from the fault plane, where there is no fault development. The pore structure characteristics of the two coal samples were analyzed and compared by means of a scanning electron microscope, mercury injection, liquid nitrogen adsorption, and Raman spectroscopy. The test results show that compared with the coal samples without faults, the coal samples at faults form micron-scale fracture zones with constant spacing, stable occurrence, and flat two walls. The pore volume and pore specific surface area of different pore sizes increase, the pore peak of mesopore (100~1000 nm) shifts from 1000 nm to 200~400 nm, and its connectivity is enhanced. The number of micropores (<10 nm) increased significantly, and the ink bottle type pores developed. Faulting also has a certain impact on the macromolecular structure of coal, which shows that the D peak area decreases and the area of G peak increases, indicating that the order degree of macromolecular structure of coal increases.
Coal permeability data are critical in the prevention and control of coal and gas outbursts in mines and are an important reservoir parameter for the development of coalbed methane. The mechanism by which permeability is affected by gas pressure is complex. We used a self-developed true triaxial seepage experimental device that collects lignite and anthracite coal samples, sets fixed axial pressure and confining pressure, and changes gas pressure by changing the orientation of the coal seam to study the influence of the gas pressure on the permeability of the coal seam under the conditions of different coal types and different bedding orientations. Coal permeability decreased rapidly and then decreased slowly and tended to be stable with the increase in gas pressure. This conforms to the power exponential fitting relationship, and the fitting degree reaches more than 99%. The permeabilities of lignite and anthracite were basically the same under various pressure conditions, indicating that the influence of coal type on coal permeability was not significant. The comparison of the two anthracite coal samples showed that the sample's permeability with a bedding plane vertical to the seepage direction was significantly lower than that of the bedding plane parallel to the seepage direction, indicating that gas seeped more easily along the bedding. The sensitivity coefficient of permeability with the change in gas pressure was calculated. The analysis showed that coal permeability was sensitive to changes in gas pressure during the low-pressure stage. When the gas pressure was greater than 0.8 MPa, the sensitivity coefficient was significantly reduced, which may be related to the slow increase in the amount of gas absorbed by the coal seam in the high-pressure stage. A theoretical calculation model of coal seam permeability considering adsorption/desorption and seepage effects was proposed and then verified with experimental results showing that the theoretical model better reflected the permeability characteristics of coal and predicted its permeability. Using the finite element simulation software COMSOL, the extraction efficiency of the coal seam gas under different gas pressure conditions was simulated. The results showed that with an increase in gas pressure, coal permeability and extraction efficiency decreased. In the low-pressure stage, the reduction in the extraction efficiency was more obvious than that in the high-pressure stage.
Surface hydraulic fracturing is an important measure for increasing reservoir permeability, which has advantages such as engineering safety and a large impact range and can be implemented ahead of the mine’s underground engineering. However, its underground outburst reduction range and effect are rarely reported, and there is a lack of connection with underground fracturing wells. Taking coalbed methane wells in the Lu’an Mining Area as an example, underground observation, microseismic monitoring, and numerical simulation methods were used to study the fracturing range and outburst control effect of surface wells. The fracturing zone of coalbed methane wells is approximately elliptical in shape, with the main fractures extending along the direction of the maximum horizontal principal stress. It can be divided into five zones: sand laying zone (radius of 140~150 m), fracture propagation zone (radius of about 180 m), fracturing fluid permeability zone (width of about 1 m), gas surge zone (width of 2~3 m), and final desorption zone (width of about 2 m). The stress around the fracturing zone increases along the direction of maximum and minimum principal stresses, while the stress value within the zone decreases, with a range of approximately 5~20% of the original geostress. The outburst reduction index Δh2 in the fracturing zone significantly decreased after fracturing. The percent of Δh2 (< 150 Pa) increased from 38.3% to 100% after fracturing. A model for evaluating the effectiveness of surface fracturing and outburst prevention was proposed, and the model was used in Tunliu Mine. The results showed that the standard‐reaching rate of extraction was high, and the danger of outburst could be completely eliminated. The research results can provide a reference for the arrangement of the coalbed methane wells and can also provide effective guidance for outburst prevention and control work during mining and excavation on a more macro scale. It provides a new idea and method for making up for the shortcomings such as the small impact range and safety hazards of underground fracturing.