We report on the evaluation of cell performances of the bifacial passivated emitter and rear cell (PERC) structures for both p- and n-type Cz-Si. We compared four conditions: Front-side illumination, with and without the rear metal contact, rear-side illumination, and double-side illumination. Furthermore, the effects of the rear contact area and the rear passivation surface recombination velocity (SRV) were evaluated. The numerical simulations were based on the experimental results of the p-type bifacial PERC performance, and we attempted to determine optimized cell designs for each condition. The results showed that the rear passivation SRV determined the bulk condition: An n-type bulk resistivity of 1 $\Omega$ -cm and p-type bulk resistivity with BO-cluster deactivation of 0.5 $\Omega$ -cm were suitable for a smaller and larger SRV, respectively.
Temporal characteristics of two-dimensional (2D) spatial images of a net production rate in a capacitively coupled plasma (CCP) reactor driven at high frequency (13.56 MHz) are investigated by newly developed computer-assisted optical emission tomography. Typical examples are presented for the absolute net formation rate of Ar(3p5) in Ar for 2 Torr and 13.56 MHz. The tomographic imaging enables us to understand a complex radial discharge structure in a CCP reactor, as well as in the central axial region.
16 September 2020 in IEEE Journal of Photovoltaics
The diffusion profiles of the front floating emitter (FFE) and front surface field (FSF) in a bifacial interdigitated back contact solar cell are optimized. The optimization results revealed that the FFE and FSF schemes are beneficial for enhancing the cell performance at the front and rear sides, respectively. Lighter doping is particularly better for the FSF scheme, and the FFE scheme requires a large diffusion depth for improving the performance. Increasing the area of the rear emitter boosts the performance of the cell, and an FFE scheme with 90 $\%$ rear emitter area is found to be the best design. Quantum efficiency mapping demonstrated that the FFE scheme suppresses the loss at the back surface field region, thereby enhancing the performance of the total cell. The FSF scheme improves the quantum efficiency for the entire region by enhancing the carrier transport in the vertical direction. Furthermore, loss analysis revealed that the FFE scheme suppresses the recombination loss at the maximum power point, which is an important advantage over the FSF scheme.
19 February 2020 in Japanese Journal of Applied Physics
Tunnel Oxide Passivated Contact (TOPCon) is a c-Si solar cell structure with tunneling oxide near the rear electrode. A full-area tunneling oxide provides sufficient passivation and low internal resistance with 1D carrier transport. Carrier tunneling mechanism is the key factor of a TOPCon solar cell; the thicker the tunneling oxide, the better is its ability to prevent minority-carrier tunneling. However, excessively thick oxide degrades majority-carrier tunneling. Therefore, the relationship between tunneling oxide thickness and cell performance is important. In this study, TOPCon solar cell structures are evaluated by varying their tunneling oxide thickness and bulk properties for both p-type and n-type bulk using numerical simulation. It is observed that the difference in bulk type is crucial to TOPCon solar cell performance: n-type material shows better performance because of its smaller minority-carrier tunneling current density and wider range of effective tunneling oxide thickness compared to p-type.
29 April 2022 in IEEE Transactions on Electron Devices
The hole impact ionization coefficient (IIC) of $\beta $ -Ga2O3 in the $\langle 010\rangle $ direction is determined by numerical simulation, as $\beta ({E}\,) = 4.0\times 10^{5} \cdot exp(-3.1\times 10^{6}/{E}\,)$ . The simulation model reproduces the experiment of the Schottky barrier diode (SBD) operation, and the investigation of the IIC is performed by varying the value to obtain the matched breakdown voltage at the reversed bias operation. The breakdown simulation results are consistent with the experimental results, with only small errors. By comparing the input modeling with the electron-only impact ionization, hole impact ionization is dominant for SBD breakdown operations.
1 June 2023 in IEEE Journal of the Electron Devices Society
The field of piezoresistance has mainly advanced through experimental research; however, the improved accuracy of simulations and the emergence of new materials have increased the importance of simulations in this field. This review discusses the methods and current topics related to simulations of piezoresistive devices. Advancing simulation modeling will facilitate the computer-aided design of piezoresistive devices, and this review introduces the means of establishing these models by discussing the current studies on simulations and calculations in this field. Two simulation methods currently exist namely, device simulations and first-principles theoretical analysis. This review focuses on numerical simulation approaches for modeling of the piezoresistive effect using the multiphysics simulations of the mechanical and electrical behaviors of piezoresistive materials.