Shengfang Huang

Prof. Shengfang Huang

China Aerodynamics Research and Development Center, Mianyang, Sichuan, China

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 June 2020 in Processes
Verified
Journal Article
Open access
PDF file
WCWeiqi Chen
Weiqi Chen
DJDi Jin
Di Jin
WCWei Cui
Wei Cui
SHShengfang Huang
Shengfang Huang
Based on an experimental system involving a pulsating airflow burner and gliding arc generator, the characteristics of gliding arc plasma at different flow rates and its control effect on the static instability of the swirl flame have been studied. The current, voltage, and power wave forms, as well as the simultaneous evolution of plasma topology, were measured to reveal the discharge characteristics of the gliding arc. A bandpass filter was used to capture the chemiluminescence of CH in the flame, and pressure at the burner outlet was acquired to investigate the static instability. Experimental results showed that there were two different discharge types in gliding arc plasma. With the low flow rate, the glow type discharge was sustained and the current was nearly a sine wave with hundreds of milliamperes of amplitude. With the high flow rate, the spark type discharge appeared and spikes which approached almost 1 ampere in 1 μs were found in the current waveform. The lean blowout limits increased when the flame mode changed from stable to pulsating, and decreased significantly after applying the gliding arc plasma. In pulsating flow mode, the measured pressure indicated that static instability was generated at the frequency of 10 Hz, and the images of flame with plasma showed that the plasma may have acted as the ignition source which injected the heat into the flame.

1 September 2018 in Applied Sciences
Verified
Journal Article
Open access
PDF file
SHShengfang Huang
Shengfang Huang
ZZZhang Zhibo
Zhang Zhibo
HSHuimin Song
Huimin Song
YWYun Wu
Yun Wu
YLYinghong Li
Yinghong Li
Finding a new ignition strategy for ignition enhancement in a lean-burn combustor has always been the biggest challenge for high-altitude, long-endurance unmanned aerial vehicles (UAVs). It is of great importance for the development of high-altitude, long-endurance aircraft to improve the secondary ignition ability of the aero-engine at high altitude where the ignition capability of the aero-engine igniter rapidly declines. An innovative ignition mode is therefore urgently needed. A novel plasma-assisted ignition method based on a multichannel discharge jet-enhanced spark (MDJS) was proposed in this study. Compared to the conventional spark igniter (SI), the arc discharge energy of the MDJS was increased by 13.6% at 0.12 bar and by 14.7% at 0.26 bar. Furthermore, the spark plasma penetration depth of the MDJS was increased by 49% and 103% at 0.12 bar and 0.26 bar, respectively. The CH* radicals showed that the MDJS obtained a larger initial spark kernel and reached a higher spark plasma penetration depth, which helped accelerate the burning velocity. Ignition tests in a model swirl combustor showed that the lean ignition limit was extended 24% from 0.034 to 0.026 at 25 m/s with 20 °C kerosene and 17% from 0.075 to 0.062 at 12 m/s with −30 °C kerosene maximally. The MDJS was a unique plasma-assisted ignition method, activated by the custom ignition power supply instead of a special power supply with an extra gas source. The objective of this study was to provide a novel multichannel discharge jet-enhanced spark ignition strategy which would help to increase the arc discharge energy, the spark plasma penetration depth and the activated area without changing the power supply system and to improve the safety and performance of aero-engines.

9 June 2022 in Energies
Verified
Journal Article
Open access
PDF file
SJSun Jiulun
Sun Jiulun
DJDi Jin
Di Jin
SHShengfang Huang
Shengfang Huang
KZKai Zhang
Kai Zhang
WCWeiqi Chen
Weiqi Chen
XCXinyao Cheng
Xinyao Cheng
In order to improve the combustion performance of a ramjet under low temperature and pressure, a gliding arc plasma actuator was designed based on a typical evaporation flameholder. The discharge characteristics, as well as the activating effect of single-channel and three-channel gliding arc plasma under different carrier gas flow rates, were studied. Results show that with the increase in the carrier gas flow rate, the average duration of the gliding arc discharge becomes shorter, while the average power increases, and the specific input energy decreases. Compared with single-channel discharge, three-channel discharge has higher discharge power and energy injection rate, which makes a bigger actuated space. Through gliding arc plasma, the kerosene is cracked and H2, CH4, C2H2, C2H4, C3H6 and other small molecule components are produced. For three-channel gliding arc discharge, the effective cracking rate and the production rate of each component are higher than those of the single-channel discharge; both of them gradually increase with the increase in the carrier gas flow rate. The experiment results indicate that three-channel gliding arc plasma can effectively widen the ignition boundary and improve the combustion efficiency of ramjet combustion. The ignition pressure boundary is expanded from 60 kPa to 50 kPa under 390 K; the combustion efficiency is increased from 76% to 82%.

10 October 2022 in Energies
Verified
Journal Article
Open access
PDF file
JLJiamao Luo
Jiamao Luo
SHShengfang Huang
Shengfang Huang
SYShunhua Yang
Shunhua Yang
WZWanzhou Zhang
Wanzhou Zhang
ZMZhongqiang Mu
Zhongqiang Mu
Numerical simulations were conducted to research the pre-cooling effects of water injection on the turbine inlet of a turbine-based combined cycle (TBCC) engine under different flight conditions. Then, the performance of the water injection pre-compressor cooling (WIPCC) engine was calculated by mathematical modelling with different water to air ratios (WAR). It was the first time that the mass injection field of the turbine inlet of a TBCC engine was simulated, and it was also the first time that the performance of a subcomponent turbine engine of a TBCC was assessed. The calculation results showed the relationship of the inlet temperature with respect to WAR, inlet length and flight Mach number. The strategy for inlet length and water mass flow was proposed in order to meet the requirements of pre-cooling. When the length of the turbine inlet was 10 times the diameter of the inlet exit, the air could be cooled by 167.5 K with WAR = 0.09. The highest evaporation ratio reached at 93%. Finally, the calculation results revealed the performance of the water-pre-cooled turbine engine, of which the flight envelope was expanded to Ma3.0 from Ma2.3 by pre-cooling. The engine thrust as well as the specific impulse were significantly improved. The thrust reached at 0.9 times the characteristic thrust meeting the TBCC mode transition requirement of thrust and working speed spectrum.

1 September 2018 in Applied Sciences
Verified
Journal Article
Open access
PDF file
SHShengfang Huang
Shengfang Huang
ZZZhang Zhibo
Zhang Zhibo
HSHuimin Song
Huimin Song
YWYun Wu
Yun Wu
ZSZhengzhong Sun
Zhengzhong Sun
YLYinghong Li
Yinghong Li
Coupled with the multichannel discharge model and plasma synthetic jet actuator (PSJA) aerodynamic model, an analytical model to predict the performance of the PSJA array is put forward. The multichannel discharge model takes these factors into consideration, the delay time in the breakdown process, the electrical transformation of the discharge channel from a capacitor to a resistor induced by the air breakdown, and the varying plasma resistance in the discharge process. The PSJA aerodynamic model is developed based on the conservation equations of mass, momentum, energy, and the lumped capacitance method. The multichannel discharge model can simulate the multichannel discharge process and give the discharge energy in the plasma channel. With a constant heating efficiency, the time-independent heating energy deposition power in a discharge channel is obtained. Importing the heating energy, the PSJA aerodynamic model presents the evolution process of the jet. Simulation results show that the jet strength induced by a single actuator decreases with the number of actuators in the PSJA array. When the actuator number increases from 1 to 20, the weakening extent of mass ejected, peak jet velocity, and jet duration time is 62%, 54%, and 33%, respectively. The discharge efficiency increases with the actuator number, while the thermodynamic efficiency decreases with the actuator number. As a result, the total energy efficiency doesn’t always increase with an increase in the number of actuators. When the discharge efficiency of a conventional one channel discharge has been a relatively large value, the total energy efficiency actually decreases with the growth of actuator number.

28 November 2024 in Energies
Verified
Journal Article
Open access
PDF file
JLJiamao Luo
Jiamao Luo
XQXin Qi
Xin Qi
SJSi Jiao
Si Jiao
YXYunlei Xiao
Yunlei Xiao
SHShengfang Huang
Shengfang Huang
SYShunhua Yang
Shunhua Yang
The burning chamber wall of the ramjet engine is facing an extremely thermal environment during normal conditions. Thermal protection measures must be taken on the wall surface of the combustion chamber. At the same time, the aircraft faces high-power electrical demand problems under high-speed cruising states. To address these issues, a second fluid-closed Brayton cycle system was introduced in this paper. Helium was utilized as the secondary fluid medium, while kerosene was used as the final heat sink. The ramjet engine chamber wall was cooled by the helium cycle system. At the same time, part of the heat absorbed by the helium cycle was transformed into electric power by a generator. This work proposes a new method of thermal management in a closed cycle. Unlike traditional methods, this proposal can regulate the mass flow rate of helium based on the requirement of heat load. A zero-dimensional numerical calculation method was established for thermodynamic analysis. The results show that as the equivalence ratio of 0.8~1.5 for the kerosene flow rate, the system can suffer the thermal load of 200~350 kJ/kg on the combustion chamber wall at the maximum kerosene allowable temperature. To ensure the normal operation of the circulating system, the mass flow ratio between the helium and the air changes from 0.02 to 0.045. Compared with the direct kerosene cooling method, the second fluid circulation method leads to the kerosene equivalent saving ratio by 2% to 14%; at the same time, such a system could generate 160~500 kJ/kg of electrical energy. This new thermal management method can achieve kerosene saving, electric power generating and suffering more thermal loads under the premise of satisfying normal work.