Di Jin

Dr. Di Jin


Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 June 2020 in Processes
Verified
Journal Article
Open access
PDF file
WCWeiqi Chen
Weiqi Chen
DJDi Jin
Di Jin
WCWei Cui
Wei Cui
SHShengfang Huang
Shengfang Huang
Based on an experimental system involving a pulsating airflow burner and gliding arc generator, the characteristics of gliding arc plasma at different flow rates and its control effect on the static instability of the swirl flame have been studied. The current, voltage, and power wave forms, as well as the simultaneous evolution of plasma topology, were measured to reveal the discharge characteristics of the gliding arc. A bandpass filter was used to capture the chemiluminescence of CH in the flame, and pressure at the burner outlet was acquired to investigate the static instability. Experimental results showed that there were two different discharge types in gliding arc plasma. With the low flow rate, the glow type discharge was sustained and the current was nearly a sine wave with hundreds of milliamperes of amplitude. With the high flow rate, the spark type discharge appeared and spikes which approached almost 1 ampere in 1 μs were found in the current waveform. The lean blowout limits increased when the flame mode changed from stable to pulsating, and decreased significantly after applying the gliding arc plasma. In pulsating flow mode, the measured pressure indicated that static instability was generated at the frequency of 10 Hz, and the images of flame with plasma showed that the plasma may have acted as the ignition source which injected the heat into the flame.

4 January 2018 in Contributions to Plasma Physics
Verified
Journal Article
Closed access
PDF file
TGTian Gan
Tian Gan
DJDi Jin
Di Jin
SGShangguang Guo
Shangguang Guo
YWYun Wu
Yun Wu
YLYinghong Li
Yinghong Li

9 June 2022 in Energies
Verified
Journal Article
Open access
PDF file
SJSun Jiulun
Sun Jiulun
DJDi Jin
Di Jin
SHShengfang Huang
Shengfang Huang
KZKai Zhang
Kai Zhang
WCWeiqi Chen
Weiqi Chen
XCXinyao Cheng
Xinyao Cheng
In order to improve the combustion performance of a ramjet under low temperature and pressure, a gliding arc plasma actuator was designed based on a typical evaporation flameholder. The discharge characteristics, as well as the activating effect of single-channel and three-channel gliding arc plasma under different carrier gas flow rates, were studied. Results show that with the increase in the carrier gas flow rate, the average duration of the gliding arc discharge becomes shorter, while the average power increases, and the specific input energy decreases. Compared with single-channel discharge, three-channel discharge has higher discharge power and energy injection rate, which makes a bigger actuated space. Through gliding arc plasma, the kerosene is cracked and H2, CH4, C2H2, C2H4, C3H6 and other small molecule components are produced. For three-channel gliding arc discharge, the effective cracking rate and the production rate of each component are higher than those of the single-channel discharge; both of them gradually increase with the increase in the carrier gas flow rate. The experiment results indicate that three-channel gliding arc plasma can effectively widen the ignition boundary and improve the combustion efficiency of ramjet combustion. The ignition pressure boundary is expanded from 60 kPa to 50 kPa under 390 K; the combustion efficiency is increased from 76% to 82%.

17 September 2022 in Processes
Verified
Journal Article
Open access
PDF file
XCXinyao Cheng
Xinyao Cheng
HSHuimin Song
Huimin Song
SJSun Jiulun
Sun Jiulun
WCWei Cui
Wei Cui
ZZZhang Zhibo
Zhang Zhibo
Yifei ZhuYifei Zhu
Yifei Zhu
The hyperburner is a key component of a TBCC engine, and its reliable ignition and stable operation are critical. The gliding arc plasma igniter driven by differential pressure has the technical advantages of low energy consumption and high jet temperature. In this paper, the electrical and flow characteristics of the gliding arc plasma igniter are studied, and the basic ignition experiment in the hyperburner is carried out. Electrical characteristic experiments show that the discharge duration, the evolution of the gliding arc and the fracture frequency are affected by the pressure difference between the inlet and outlet of the igniter (Δp). With the increase in Δp, the frequency of the trapezoidal envelope in the voltage and current waveforms increases, and the frequency of the evolution and fracture of the gliding arc increases. The continuous discharge time of the gliding arc decreases when Δp = 550 Torr. The flow characteristic experiments show that the velocity of the swirl sheath is increased and the protective effect on the gliding arc is enhanced with the increase in Δp. In the range of 20–550 Torr, the jet length first increases and then decreases with the increase in Δp. The jet length reaches a maximum of 31 mm at Δp = 50 Torr. Basic ignition experiments show that proper Δp can widen the lean ignition limit and shorten the ignition delay time. In the working conditions of this paper, the ignition effect is the best when Δp = 350 Torr, which can widen the lean ignition limit by 37.5% and shorten the ignition delay time by 17%. After increasing the oil–gas ratios, the combustion is more complete and the ignition delay time can be shortened by 93.1% at most.

5 October 2022 in International Journal of Aeronautical and Space Sciences
Verified
Journal Article
Closed access
PDF file
HLHao Liu
Hao Liu
DJDi Jin
Di Jin

19 August 2022 in Combustion Science and Technology
Verified
Journal Article
Closed access
HLHao Liu
Hao Liu
FSFeilong Song
Feilong Song
DJDi Jin
Di Jin
ZYZhao Yang
Zhao Yang
SXShida Xu
Shida Xu
XYXingkui Yang
Xingkui Yang
The atomization and mixing process in a linearized rotating detonation engine supplied with non-premixed kerosene was optically analyzed by experiment. Schlieren, simultaneous LIF/Mie technique and particle/droplet image analysis (PDIA) system were applied to study flow field structure and spray properties under various conditions, including air flow rate, fuel flow rate and flow velocity at injector position. Aerodynamic shearing force and fuel injection pressure contribute to the refinement and uniformity of the spray. The distribution of fuel in the combustor has obvious stratification, which makes the local equivalence ratio higher than the set global equivalence ratio. Compared with full-scale RDE experiments, the detonation wave exists in a dual-wave collision mode. The increased kerosene flow rate refines the droplets, which raises the detonation wave velocity. Furthermore, the detonation wave will propagate more stably due to the slower airflow velocity at higher combustor pressure.