Nano-crystalline diamond (NCD) coating to improve the performance of cutting tools, as the coating thickness varies, the cutting performance and lifespan of the tool varies because the radius of its cutting edge and coating surface roughness are altered. Therefore, an in-depth analysis on the impact of the variations in coating thickness on the cutting tool abrasion and quality of machined surface is necessary. In this study, two NCD ball endmills were coated with 8 and 12 μm thicknesses, and the tool abrasion and roughness of the machined plane were observed after milling. Furthermore, the morphology of the coated surface and abrased cutting edge were observed using a 3D confocal microscope. Consequently, we observed that individual nodules were formed on the continuous aggregates as the coating thickness increased, which increased the coated surface roughness. The two damage modes of the aggregation determined the dominant abrasion that occurred on the cutting edges of both types of coating thicknesses. Delamination and crater wear caused a sharp increase in the roughness of the machined surface. In summary, the increase in coating thickness delayed the delamination of the coating but increased the roughness of the cutting edge, which reduced the machined surface roughness.
The high-purity G5 graphite material is widely used for glass moulding and provides high hardness and brittleness because it is sintered to fine particles unlike other graphite materials. Hence, tool cutting of a G5 workpiece is performed by local fracture instead of plastic deformation of the machined surface. Although a diamond-coated tool with outstanding hardness is used to machine very hard graphite, the tool shows variability regarding the service life and machining performance depending on the grain size, even in the same machining environment. We investigated the wear and change trend of machined surface roughness considering microcrystalline diamond (MCD) and nanocrystalline diamond (NCD)-coated tools, which are generally used to machine graphite materials, and analysed their relation with coating. For rough machining, the MCD-coated tool, for which the delamination of coating occurred later, showed less wear and improved machined surface roughness. For precision machining, the NCD tool showed less tool wear rate relative to the cutting length, leading to a small difference in the machined surface roughness between the two tools. We conclude that if rough and precision machining processes are performed using the same cutting tool, the MCD-coated tool is advantageous in terms of service life, while the difference in roughness of the final machined surface between the tools is negligible.
The domain of edge displays with 2.5D or 3D curved designs has been expanded to improve user convenience. The currently available 3D cover glass offers a limited curvature radius of at least 5 mm and a curvature less than 88°, due to limitations in the undercuts and formability of parts. The development of a full 3D cover, applicable to next-generation displays, requires cover glass molding technology with a curvature exceeding 90°. Here, a mold design and molding process, which addresses the current limitations by dividing the existing glass molding press (GMP) process into two stages, is proposed. The bending geometry of the glass prepared on the basis of the proposed mold design plan during single-step compression forming and two-step compression forming was predicted using commercial analysis software. A molding product with a curvature radius of 2.5 mm and an angle of curvature of 138.9° was produced when process conditions with bending by up to 180° with no damage were applied during actual forming experiments. Further research on annealing and cooling processes of GMP is expected to enable the design and process implementation to manufacture curved glass with a single curvature of at least 90° and multiple curvatures.
In this paper, we introduce a microabrasive air jet (micro-AAJ) machining system and describe machining results obtained while using it. Our research activities have focused on the development of micro-AAJ machining methods for friction reduction without requiring a mask. Through this study, we want to show that such processing is possible without a mask when using the AAJ method. In this paper, a micro-AAJ machining system is introduced, and the processing results are described. By comparing the friction coefficient of texturing under various conditions, the relative relationship between the surface shape and the friction coefficient can be identified. We investigated the effect of the relationship between rotating velocity, traverse speed, density of the patterned area and injection pressure on friction. The friction is decreased with a low traverse speed and high-density patterned area under high-speed driving conditions, as verified by experiments using a friction test system.