Ata Hojatkashani

Dr. Ata Hojatkashani

Islamic Azad University South Tehran Branch, Tehran, Tehrān, Iran
orcid

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 September 2022 in Materials
Verified
Journal Article
Open access
PDF file
Milad EskandariniaMilad Eskandarinia
Milad Eskandarinia
MEMina Esmailzade
Mina Esmailzade
Ata HojatkashaniAta Hojatkashani
Ata Hojatkashani
ARAida Rahmani
Aida Rahmani
SJSoheil Jahandari
Soheil Jahandari
This study employed Taguchi-Grey relational analysis to optimize the influences of binder content, the molarity of sodium hydroxide (SH) solution, alkaline solution to binder content (Al/Bi) ratio, water to alkali-activated solids (W/S) ratio, and sodium silicate to sodium hydroxide solution (SS/SH) ratio on the workability, setting time, and compressive strength of alkali-activated slag-based concrete (AASC). Then, the recycled tire steel fibers (RTSF) were introduced into the optimized mixture in different dosages, and the physical and mechanical properties of fiber-reinforced AASC (FR-AASC) were evaluated. RTSF inclusion negatively affected the workability and increased the density while slightly reducing the water absorption. Additionally, the compressive strength and flexural behavior of FR-AASC improved by increasing the RTSF content. The analysis of images taken from flexural specimens through the Digital Image Correlation technique (DIC) revealed that higher RTSF dosage caused a curved macro crack with several branches alongside, leading to a better post-cracking performance in terms of strength and toughness.

21 July 2022 in Structures
Verified
Journal Article
Closed access
VGVandad Garmeh
Vandad Garmeh
AAAbbas Akbarpour
Abbas Akbarpour
MAMohammadreza Adibramezani
Mohammadreza Adibramezani
Ata HojatkashaniAta Hojatkashani
Ata Hojatkashani
MAMahdi Adibi
Mahdi Adibi

1 October 2021 in Structures
Verified
Journal Article
Closed access
VGVandad Garmeh
Vandad Garmeh
AAAbbas Akbarpour
Abbas Akbarpour
MAMohammadreza Adibramezani
Mohammadreza Adibramezani
Ata HojatkashaniAta Hojatkashani
Ata Hojatkashani
MAMahdi Adibi
Mahdi Adibi

25 November 2022 in Structural Engineering International
Verified
Journal Article
Closed access
RHRahim Hassani
Rahim Hassani
Ata HojatkashaniAta Hojatkashani
Ata Hojatkashani
RBRouhollah Basirat
Rouhollah Basirat
In this paper, in addition to the linear analysis used for typical tunnels, nonlinear seismic analysis of a tunnel has been investigated using pseudo-static method and a damaged concrete behavior model introduced in ABAQUS® software. The simulations were carried out under three conditions, free field, ovaling and racking, at two hazardous earthquake levels according to an Operation Design Earthquake (ODE) and a Maximum Design Earthquake (MDE). Then, the structural capacity curve and the behavior factor for the final tunnel lining were obtained. In order to extend the studies as well as to verify the pseudo-static analyses, seven nonlinear dynamic analyses compatible with the site under MDE conditions have been performed. The results showed that the tunnel lining procedure created limited tensile cracks under compression. At the bottom corners of the tunnel structure, the resultant stresses in the tunnel lining under two earthquakes caused failure and created tensile cracks. Therefore, it was necessary to reinforce the lining at corners. Comparison between different nonlinear time history seismic analysis and pseudo-static methods indicated that the pseudo-static methods resulted in 10–30% less acceleration than the average results obtained from time history analysis.

10 February 2018 in International Journal of Advanced Structural Engineering
Verified
Journal Article
Open access
PDF file
Ata HojatkashaniAta Hojatkashani
Ata Hojatkashani
SZSara Zanjani
Sara Zanjani
Rehabilitation of weak and damaged structures has been considered widely during recent years. A relatively modern way of strengthening concrete components is to confine parts under tension and shear by means of carbon fiber reinforce polymer (CFRP). This way of strengthening due to the conditions of composite materials such as light weight, linear elastic behavior until failure point, high tensile strength, high elastic modulus, resistance against corrosion, and high fatigue resistance has become so common. During structural strengthening by means of not pre-stressed FRP materials, usually, it is not possible to benefit from the maximum capacity of FRP materials. In addition, sometimes, the expensive cost of such materials will not make a suitable balance between rates of strengthening and consuming spending. Thus, pre-stressing CFRP materials has an undeniable role in the effective use of materials. In the current research, general procedure of simulation using finite-element method (FEM) by means of the numerical package ABAQUS has been presented. In this article, 12 reinforced concrete (RC) models in two states (strengthened with simple and pre-stressed CFRP) under cycling loading have been considered. A parametric study has been carried out in this research on the effects of parameters such as CFRP surface area, percentage of tensile steel rebar and pre-stressing stress on ultimate load carrying capacity (ULCC), stiffness, and the ability of depreciation energy for the samples. In the current article also, for design parameters, percentages of tensile steel rebars, surface area of CFPR sheets, and the effective pre-stressing stress in RC beams retrofitted with pre-stressed CFPR sheets have investigated. In this paper, it was investigated that using different amount of parameters such as steel rebar percentage, CFRP surface area percentage, and CFRP pre-stressing, the resulted ULCC and energy depreciation of the specimens was observed to be increasing and decreasing. Results from examined specimens with optimum steel rebar percentage, CFRP surface area percentage, and CFRP pre-stressing which had the most enhancement on ULCC and energy depreciation are reported in the current article.

8 September 2022 in Processes
Verified
Journal Article
Open access
PDF file
HJHossein Nematian Jelodar
Hossein Nematian Jelodar
Ata HojatkashaniAta Hojatkashani
Ata Hojatkashani
RMRahmat Madandoust
Rahmat Madandoust
AAAbbas Akbarpour
Abbas Akbarpour
SHSeyed Azim Hosseini
Seyed Azim Hosseini
This paper investigates bending and compressive strengths as mechanical characteristics of cement-based repair mortar containing nano-silica (NS) and micro-silica (SF) as cement replacements particles and polyvinyl alcohol (PVA) fibers. The mentioned materials were added to the mortar in three different conditions, including single (just one material), binary (mixture of two admixtures), and ternary (mixture of all three admixtures) modes. The use of PVA fibers, nano-silica and micro-silica in the triple combination of a cement-based mortar is the primary objective of the current research. In total, 28 mix designs with various percentages of particles and fiber were employed in the current study, and 112 different specimens were prepared to conduct the experimental research. The compressive and flexural strength results have been selected as the criteria for obtaining the optimum mix design for each condition. In order to specify the mechanical characteristics of specimens, a compressive test was carried out according to ACI 318, and the three-point bending test was utilized according to BS EN 1015-11. The results obtained from this study show that the mixture containing 10% silica fume (SF10) can be considered the optimum mix design for the single-mode condition. For such a mix design, a flexural strength increase of 27% and a compressive strength improvement of 48% were determined in comparison to the reference mixture design. The mixture containing nano-silica at 2% and silica fume at 8% (NS2SF8) was the optimum mix design in the binary mode condition. With the current mix design, a flexural strength improvement of 24% and a compressive strength increase of 49% in a 28-day specimen were recorded. Finally, under the ternary mode condition, a flexural strength enhancement of 3.5% and a compressive strength improvement of 4.6% were obtained. Additionally, the mixture design containing a PVA content of 0.75% and an SF content of 10% (PVA0.75SF10) was considered optimum.