Keisuke Kusaka

Dr. Keisuke Kusaka

orcid

Research Focus & Metrics

Academic Career Length

25Years (2002-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 July 2017 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
HWHiroki Watanabe
Hiroki Watanabe
TSTomokazu Sakuraba
Tomokazu Sakuraba
KFKeita Furukawa
Keita Furukawa
Keisuke KusakaKeisuke Kusaka
Keisuke Kusaka
JIJunichi ITOH
Junichi ITOH
In the present, an active power decoupling method without an additional component is proposed for a DC to single-phase AC converter, which is constructed of a flying-capacitor DC/DC converter (FCC) and the voltage source inverter (VSI). In particular, a small flying capacitor in the FCC is used for both a boost operation and a double-line-frequency power ripple reduction. Thus, the DC link capacitor value can be minimized in order to avoid the use of a large electrolytic capacitor. In addition, component design, of e.g., the boost inductor and the flying capacitor, is clarified when the proposed control is applied. Experiments were carried out using a 1.5-kW prototype in order to verify the validity of the proposed control. The experimental results revealed that the use of the proposed control reduced the DC link voltage ripple by 74.5%, and the total harmonic distortion (THD) of the inverter output current was less than 5%. Moreover, a maximum system efficiency of 95.4% was achieved at a load of 1.1 kW. Finally, the high power density design is evaluated by the Pareto front optimization. As a result, the proposed topology achieves the highest power density (5.3kW/dm3) among the topologies considered herein.

31 May 2017 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
KIKent Inoue
Kent Inoue
Keisuke KusakaKeisuke Kusaka
Keisuke Kusaka
JIJunichi ITOH
Junichi ITOH
Two proposed methods of reducing radiation noise caused by inductive power transfer (IPT) systems using spread spectrum techniques were experimentally demonstrated. In IPT systems for electric vehicles (EVs) or plug-in hybrid EVs (PHEVs), noise reduction techniques are necessary because the radiation noise from the IPT system for EVs or PHEVs must not exceed the limits defined by noise standards, such as the well-known regulation set by the International Special Committee on Radio Interference (CISPR). In the proposed methods, the radiation noise from the transmission coils of the IPT system is spread in the frequency domain by randomly changing the output frequency of the inverter. The output frequency is selected according to the generation of pseudorandom numbers. In the first proposed method, spread spectrum with a uniform distribution (SSUD), the output frequency is selected from the frequency range of 80 to 90 kHz with an even distribution. In the second method, spread spectrum with a biased distribution (SSBD), the output current of the inverter is considered. The possibility of selecting an output frequency in the given range is biased in proportion to the combined impedance from the transmission coil and the resonance capacitors on the primary side. In experiments with a 3-kW prototype, when SSUD and SSBD were applied, the fundamental components of the radiation noise were suppressed by 4.45 and 8.27 dBA, respectively, in comparison with the noise obtained using the conventional system, which operates the inverter at a fixed frequency.

1 September 2015
Verified
Conference Paper
Closed access
Keisuke KusakaKeisuke Kusaka
Keisuke Kusaka
MKMasakazu Kato
Masakazu Kato
KOKoji Orikawa
Koji Orikawa
JIJun-Ichi Itoh
Jun-Ichi Itoh
IHIsamu Hasegawa
Isamu Hasegawa
TKTakeshi Kondo
Takeshi Kondo
Medium-voltage motor drive systems, medium-voltage inverters, which have an input voltage and an output voltage of 3.3 kV or 6.6 kV, are widely used in industry applications. In the medium-voltage inverter, robust galvanic isolation among a control circuit and each gate drive supplies is required in order to drive high-voltage switching devices. In present, a transformer, which is designed to satisfy the safety standards, provides galvanic isolation. However, transformers prevent cost reduction of the isolation system. In this paper, the galvanic isolation system using only printed circuit boards are proposed. Moreover, a three-phase inverter is driven using the isolation system in order to confirm the utility of the isolation system. The proposed system transmits power from the transmitting board to six receiving boards using each transmitting coils made on the printed circuit boards. The air gap among the printed circuit boards assumes galvanic isolation. From the experimental results, it is confirmed that the three-phase inverter can be driven by the proposed galvanic isolation system.

1 December 2011
Verified
Conference Paper
Closed access
Keisuke KusakaKeisuke Kusaka
Keisuke Kusaka
JIJun-Ichi Itoh
Jun-Ichi Itoh
This paper demonstrates that SiC and GaN diode rectifiers are used in a magnetic resonant coupling (MRC) for wireless power transfer system. The size of the resonance coils, which are used in the wireless power transfer using a MRC, depends on the transmission frequency. So, the MRC is desired to operate at a high frequency in the Industry Science Medical (ISM) band such as 13.56 MHz. In the receiving side, a rectifier which converts to the DC voltage from high frequency AC voltage is necessary to supply the power to the applications such as a battery charger for EV and home appliances. The experimental results show the maximum efficiency from a Radio Frequency (RF) power supply to DC outputs is 75.2% when the transmission distance is 150 mm. In addition, A power loss separation method of the wireless power transfer system is discussed in this paper. The experimental results verify the reflected power of the resonance coil which dominates the largest amount of the loss in the total loss. Therefore, the suppression of the reflected power is important for the wireless power transfer system using a MRC.

23 July 2018 in IEEE Transactions on Industry Applications
Verified
Journal Article
Closed access
SNSatoshi Nagai
Satoshi Nagai
Keisuke KusakaKeisuke Kusaka
Keisuke Kusaka
JIJunichi ITOH
Junichi ITOH
This paper proposes a Zero-Voltage Ride-Through (ZVRT) method and an LCL filter design method to meet the Fault Ride-Through (FRT) requirements for a single-phase grid-connected inverter with a minimized LCL filter. A high inverter-output-current overshoot occurs at a grid voltage sag and a grid voltage recovery, when a low-inductance LCL filter design is employed in order to minimize the filter volume. In order to suppress the current overshoot, a high-speed gate-block operation and the design method of the minimized LCL filter are proposed. In particular, the filter design considers the delay time in the gate-block operation in order to clarify the reduction limitation of the inductance in the LCL filter. As a result, the maximum inverter-output-current overshoot is suppressed to 146% by the high-speed gate-block operation and the designed LCL filter, where the impedances of an interconnected inductor and a filter inductor are 1.0% and 0.78% of the inverter normalized impedance, respectively. Therefore, it is possible to meet the FRT requirements with the proposed ZVRT method even with the minimized LCL filter.

1 July 2022 in IEEJ Journal of Industry Applications
Verified
Journal Article
Closed access
PDF file
Keisuke KusakaKeisuke Kusaka
Keisuke Kusaka
RKRintaro Kusui
Rintaro Kusui
JIJun-Ichi Itoh
Jun-Ichi Itoh
DSDaisuke Sato
Daisuke Sato
TSTetsu Shijo
Tetsu Shijo
MIMasaaki Ishida
Masaaki Ishida
Techniques to reduce electromagnetic emission in high-power wireless power transfer (WPT) systems are required because the radiated emission of the WPT must comply with the regulation published by CISPR (International Special Committee on Radio Interference) and ICNIRP (International Commission on Non-ionizing Radiation Protection.) In this paper, a three-phase WPT system, which complies with CISPR 11, group 2, class A is developed. The three-phase WPT system has six solenoid coils on the primary side and six solenoid coils on the secondary side. The use of 12 coils allows radiation noise reduction as the radiation noise is emitted to the opposite direction of the pairs of coils. Moreover, the cross-coupling among six coils on the common side is canceled by adjusting the position of coils. The electromagnetic compatibility of the 22kW prototype is evaluated in a 10 m anechoic chamber according to the CISPR 11 guideline. The prototype fully complies with CISPR 11, class A, group 2 with respect to electromagnetic emission. Moreover, it also complies with ICNIRP guidelines in 2010 at a distance of 340 mm or more from the edge of the coils.