Junichi ITOH

Junichi ITOH


Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 July 2017 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
HWHiroki Watanabe
Hiroki Watanabe
TSTomokazu Sakuraba
Tomokazu Sakuraba
KFKeita Furukawa
Keita Furukawa
Keisuke KusakaKeisuke Kusaka
Keisuke Kusaka
JIJunichi ITOH
Junichi ITOH
In the present, an active power decoupling method without an additional component is proposed for a DC to single-phase AC converter, which is constructed of a flying-capacitor DC/DC converter (FCC) and the voltage source inverter (VSI). In particular, a small flying capacitor in the FCC is used for both a boost operation and a double-line-frequency power ripple reduction. Thus, the DC link capacitor value can be minimized in order to avoid the use of a large electrolytic capacitor. In addition, component design, of e.g., the boost inductor and the flying capacitor, is clarified when the proposed control is applied. Experiments were carried out using a 1.5-kW prototype in order to verify the validity of the proposed control. The experimental results revealed that the use of the proposed control reduced the DC link voltage ripple by 74.5%, and the total harmonic distortion (THD) of the inverter output current was less than 5%. Moreover, a maximum system efficiency of 95.4% was achieved at a load of 1.1 kW. Finally, the high power density design is evaluated by the Pareto front optimization. As a result, the proposed topology achieves the highest power density (5.3kW/dm3) among the topologies considered herein.

3 April 2017 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
TNToshiki Nakanishi
Toshiki Nakanishi
JIJunichi ITOH
Junichi ITOH
This paper presents a high power density design for a step-down rectifier incorporating a modular multilevel converter (MMC) in a power system connected to a 6.6 kV ac grid. In particular, the relationship among the number of cells, the output voltage of the MMC, and the overall volume is clarified. A proposed design flowchart focuses on minimizing volumes of cell capacitors, heat sinks, and arm inductors by using optimal number of cells. Moreover, the commercial electrolytic capacitors are used as the cell capacitor. Besides, the formulae used to determine the ripple currents in the electrolytic capacitor and the arm inductor are presented, along with that for the semiconductor loss. Each of these formulae were verified experimentally using a miniature model and theoretical values from all formulae agree with the measured values within minimal deviations that are discussed with regard to the design of a practical converter for a 6.6 kV system. Finally, the conditions necessary to achieve high power density in an MMC are provided, based on volume evaluations of the electrolytic capacitor, the arm inductor, and the heat sink. Using this optimization process, an MMC design achieved a volume reduction of approximately 90% compared to a conventional system.

31 May 2017 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
KIKent Inoue
Kent Inoue
Keisuke KusakaKeisuke Kusaka
Keisuke Kusaka
JIJunichi ITOH
Junichi ITOH
Two proposed methods of reducing radiation noise caused by inductive power transfer (IPT) systems using spread spectrum techniques were experimentally demonstrated. In IPT systems for electric vehicles (EVs) or plug-in hybrid EVs (PHEVs), noise reduction techniques are necessary because the radiation noise from the IPT system for EVs or PHEVs must not exceed the limits defined by noise standards, such as the well-known regulation set by the International Special Committee on Radio Interference (CISPR). In the proposed methods, the radiation noise from the transmission coils of the IPT system is spread in the frequency domain by randomly changing the output frequency of the inverter. The output frequency is selected according to the generation of pseudorandom numbers. In the first proposed method, spread spectrum with a uniform distribution (SSUD), the output frequency is selected from the frequency range of 80 to 90 kHz with an even distribution. In the second method, spread spectrum with a biased distribution (SSBD), the output current of the inverter is considered. The possibility of selecting an output frequency in the given range is biased in proportion to the combined impedance from the transmission coil and the resonance capacitors on the primary side. In experiments with a 3-kW prototype, when SSUD and SSBD were applied, the fundamental components of the radiation noise were suppressed by 4.45 and 8.27 dBA, respectively, in comparison with the noise obtained using the conventional system, which operates the inverter at a fixed frequency.

25 July 2018 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
KNKoroku Nishizawa
Koroku Nishizawa
JIJunichi ITOH
Junichi ITOH
AOAkihiro Odaka
Akihiro Odaka
ATAkio Toba
Akio Toba
HUHidetoshi Umida
Hidetoshi Umida
This paper proposes a novel space vector pulse width modulation (SVPWM) strategy to reduce the switching frequency-order DC-link current ripple for a two-level three-phase voltage source inverter operating over a wide range of the load power factor. The fluctuation of the DC-link current around its average value is minimized by optimization of the utilized voltage space vectors to reduce the DC-link current ripple, which extends the lifetime of the DC-link electrolytic capacitors. Furthermore, the proposed strategy can be adapted to a motor drive system, where a wide variation of the load power factor is desired, by changing the optimized combinations of the voltage space vectors according to the polarities of the output phase currents. Experiments with application of the novel SVPWM confirm that the DC-link current ripple is reduced by up to 29.5% compared to that with the conventional SVPWM strategy. Moreover, the analytical and experimental results confirm that the proposed SVPWM reduces the DC-link current ripple in both driving mode and regenerative braking mode, as well as with any load power factor.

17 November 2017 in IEEE Transactions on Industry Applications
Verified
Journal Article
Closed access
NTNagisa Takaoka
Nagisa Takaoka
HTHiroki Takahashi
Hiroki Takahashi
JIJunichi ITOH
Junichi ITOH
This paper proposes a bi-directional isolated single-phase matrix converter with a center-tapped transformer, which is used in a battery storage system connecting to a single-phase AC load. The proposed converter consists of a full bridge inverter, a high-frequency center-tapped transformer, and a matrix converter. The matrix converter is employed with a pulse density modulation in order to achieve zero-voltage switching (ZVS). On the other hand, a common mode voltage of the center-tapped transformer and a small capacitor are utilized in order to absorb the power ripple of the single-phase AC load without additional switches. Furthermore, the switches in the full bridge inverter partially achieve ZVS in order to reduce the switching loss. These characteristics result in a high-power-density converter. As the experimental results with a 1kW-prototype, the proposed converter reduces the DC current ripple generated by a single-phase AC load by 80.2% in the discharging mode, and 76.8% in the charge mode. Besides, the low output voltage THD in the discharge are below 3.0% over entire the output power range.

1 January 2019 in IEEJ Journal of Industry Applications
Verified
Journal Article
Open access
PDF file
KKKeisuke Kusaka
Keisuke Kusaka
KFKeita Furukawa
Keita Furukawa
JIJunichi ITOH
Junichi ITOH
A three-phase wireless power transfer (WPT) system, which has six primary coils and six secondary coils is proposed in this paper. The three-phase WPT system reduces the radiation noise by canceling the noise using pairs of coils placed opposite to each other. However, a magnetic interference among the multiple coils decreases the transmission efficiency due to a circulating current among the primary coils, and the secondary coils in WPT systems with multiple coils. The proposed three-phase WPT system cancels out the effect due to the interference among the six coils on each side. First, the WPT system with the 12 coils is proposed. Then, a canceling condition of the magnetic interference among the coils is mathematically introduced from the voltage equation on the coils. Finally, the proposed WPT system is experimentally demonstrated with the 3-kW prototype. The experimental result shows that the radiation noise at the fundamental frequency is suppressed from 12.2 dB mu A to 2.1 dB mu A.