Hiroki Watanabe

Dr. Hiroki Watanabe


Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 July 2017 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
HWHiroki Watanabe
Hiroki Watanabe
TSTomokazu Sakuraba
Tomokazu Sakuraba
KFKeita Furukawa
Keita Furukawa
Keisuke KusakaKeisuke Kusaka
Keisuke Kusaka
JIJunichi ITOH
Junichi ITOH
In the present, an active power decoupling method without an additional component is proposed for a DC to single-phase AC converter, which is constructed of a flying-capacitor DC/DC converter (FCC) and the voltage source inverter (VSI). In particular, a small flying capacitor in the FCC is used for both a boost operation and a double-line-frequency power ripple reduction. Thus, the DC link capacitor value can be minimized in order to avoid the use of a large electrolytic capacitor. In addition, component design, of e.g., the boost inductor and the flying capacitor, is clarified when the proposed control is applied. Experiments were carried out using a 1.5-kW prototype in order to verify the validity of the proposed control. The experimental results revealed that the use of the proposed control reduced the DC link voltage ripple by 74.5%, and the total harmonic distortion (THD) of the inverter output current was less than 5%. Moreover, a maximum system efficiency of 95.4% was achieved at a load of 1.1 kW. Finally, the high power density design is evaluated by the Pareto front optimization. As a result, the proposed topology achieves the highest power density (5.3kW/dm3) among the topologies considered herein.

13 August 2019 in Energies
Verified
Journal Article
Open access
PDF file
HWHiroki Watanabe
Hiroki Watanabe
JIJunichi ITOH
Junichi ITOH
NKNaoki Koike
Naoki Koike
SNShinichiro Nagai
Shinichiro Nagai
In this paper, a DC–single-phase AC power converter with an LLC resonant converter is presented for a photovoltaic (PV) micro-inverter application. This application requires the leakage current suppression capability. Therefore, an isolated power converter is usually combined for DC/AC systems. The LLC resonant converter is the one of the isolated power converter topologies, and it has good performance for conversion efficiency with easy control. On the other hand, a double-line frequency power ripple has to be compensated for in order to improve the performance of the maximum power point tracking (MPPT). Therefore, a bulky electrolytic capacitor is usually necessary for the power converter. However, the electrolytic capacitor may limit the lifetime of the micro-inverter. This paper introduces the PV micro-inverter with a LLC resonant converter. In addition, the active power decoupling circuit is applied in order to compensate the double-line frequency power ripple by the small capacitor in order to eliminate the electrolytic capacitor. Finally, the transformer design is considered in order to reduce the transformer losses. As a result, the conversion efficiency of the LLC converter is improved by 1% when the litz wire has many strands.

1 January 2024 in IEEE Transactions on Industry Applications
Verified
Journal Article
Closed access
HWHiroki Watanabe
Hiroki Watanabe
KYKoki Yamanokuchi
Koki Yamanokuchi
YIYoshinari Ikeda
Yoshinari Ikeda
YTYoshikazu Takahashi
Yoshikazu Takahashi
JIJunichi ITOH
Junichi ITOH
This paper presents a Universal Smart Power Module (USPM) which responds instantaneously to fluctuating power sources such as solar and wind power and fully addresses the rapidly expanding renewable energy market by combining universality and smartness. USPM consists of a main circuit as an H-bridge converter, high-speed controller, gate driver, and EMI filter into one module. Conventional power electronics design requires complicated know-how and specialized skills such as circuit design, digital control, thermal design, and EMI. The USPM concept simplifies the power electronics design because this system realizes every power converter by a combination of several USPMs. The USPM system consists of the master controller and several USPMs. The master controller gives voltage and current commands to USPMs by wireless communication to regulate the operation of USPMs. USPM realizes excellent feedback control by the high-speed controller in order to follow the command from the master controller rapidly. The core power module using the wide-bandgap device in USPM is also developed to improve the switching characteristics and the power density of USPM. As the technology for ultra-miniaturization, ADB (Atomic Diffusion Bonding) is developed and applied to the drain side of the SiC-MOSFET to achieve low thermal resistance, and bumping technology to the source side of it to achieve low inductance. This paper introduces the detail of the concept of the USPM systems and the core power module. Finally, the example of the USPM system for the PV power conditioner is demonstrated by the experiment.

23 August 2023 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
KYKoki Yamanokuchi
Koki Yamanokuchi
HWHiroki Watanabe
Hiroki Watanabe
JIJunichi ITOH
Junichi ITOH
This article proposes a current droop control for series-connected current source converters in a universal smart power module (USPM) concept. In this concept, power conversion systems are constructed by USPMs, which have a high-speed controller and autonomous distributed control. USPM enhances versatility by its high flexibility and usability compared to power electronics building blocks, which is a similar concept. In this system, noninterference control is required because these USPMs are operated independently without sharing information with each other. Droop control for the voltage source converter is a common solution for parallel-connected converters. Likewise, a stabilization method for the current-source-type converter connected in series is necessary for the USPM system. The proposed method in this article solves these problems. In particular, the configuration of the current controller and its gain design method is verified in order to achieve a stable condition and high-speed response. The experimental results for the 500-W system reveal that the stability limit of the PI control adopting the proposed current droop control agrees with the analytical results with an error of 1.3%. Furthermore, this article demonstrates that the current deviation agrees with that of the design value with an error of 3.0% or less.

1 May 2018 in IEEJ Transactions on Industry Applications
Verified
Journal Article
Closed access
JIJunichi ITOH
Junichi ITOH
TSTomokazu Sakuraba
Tomokazu Sakuraba
HLHoai Nam Le
Hoai Nam Le
HWHiroki Watanabe
Hiroki Watanabe
Keisuke KusakaKeisuke Kusaka
Keisuke Kusaka

1 October 2017
Verified
Conference Paper
Closed access
JIJunichi ITOH
Junichi ITOH
TSTomokazu Sakuraba
Tomokazu Sakuraba
HWHiroki Watanabe
Hiroki Watanabe
NTNagisa Takaoka
Nagisa Takaoka
This paper proposes a single-phase AC converter with an active power decoupling circuit operated in DCM (discontinuous current mode) for PV (photovoltaic) systems. The proposed converter consists of an H-bridge single-phase AC converter and a boost converter, and a compensation circuit employed with a small capacitor for the power ripple. In many active power decoupling topologies that have been studied, an additional magnetic component for the voltage control of the buffer capacitor is required. This worsens the power density and the converter efficiency. In the proposed converter, the boost inductor is utilized for both the boost operation and the active power decoupling operation by using DCM. In this paper, by harmonic analysis, the effectiveness of the active power decoupling method is evaluated. As a calculating result, the maximum power density of the proposed converter is 1.26 times higher than that of the passive topology. Especially, the boost inductor volume can be reduced by 42.7% applying by DCM. The fundamental operation is confirmed by a 1-kW prototype. From experimental results, a second-order harmonics on the input current is reduced by 90.2% with the proposed active power decoupling method. In addition, the maximum efficiency of 96.0% is achieved at the output power of 600 W.