Peng Wu

Dr. Peng Wu

College of Energy Engineering, Zhejiang University, Hangzhou 310027, China

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2015 in Journal of Water Resources Planning and Management
Verified
Journal Article
Closed access
PWPeng Wu
Peng Wu
ZLZhounian Lai
Zhounian Lai
Dazhuan WuDazhuan Wu
Dazhuan Wu
LWLeqin Wang
Leqin Wang
In applications where demand on a water supply system changes frequently and widely, the operating conditions of pumps always deviate from the design conditions, and this error leads to poor efficiency and reliability. For energy saving and longer service life, a parallel pump system was supplied, with the valves and rotational speed controls approximating the system’s operating conditions closer to the designed conditions for different consumer loads. The developed optimization model employs a genetic algorithm (GA) aiming at the pumps’ maximum efficiency. A theoretical solution based on the Lagrange multiples method was proved. Experiments on two identical pumps were carried out. The presented model gives optimal input data for the pumps’ rotational speed and valve positions. The results show that control valves are especially helpful for improvement of a single pump’s efficiency and reliability. However, in the system of parallel pumps, throttling losses in the valves caused a significant decline in system efficiency. Therefore, the developed optimization model provides balance between efficiency and reliability by offering the suitable operating mode.

10 October 2016 in Journal of Fluids Engineering
Verified
Journal Article
Closed access
PDF file
PYPeng Yan
Peng Yan
NCNING CHU
NING CHU
Dazhuan WuDazhuan Wu
Dazhuan Wu
LCLinlin Cao
Linlin Cao
SYShuai Yang
Shuai Yang
PWPeng Wu
Peng Wu
In this study, a double volute centrifugal pump with relative low efficiency and high vibration is redesigned to improve the efficiency and reduce the unsteady radial forces with the aid of unsteady computational fluid dynamics (CFD) analysis. The concept of entropy generation rate is applied to evaluate the magnitude and distribution of the loss generation in pumps and it is proved to be a useful technique for loss identification and subsequent redesign process. The local Euler head distribution (LEHD) can represent the energy growth from the blade leading edge (LE) to its trailing edge (TE) on constant span stream surface in a viscous flow field, and the LEHD is proposed to evaluate the flow field on constant span stream surfaces from hub to shroud. To investigate the unsteady internal flow of the centrifugal pump, the unsteady Reynolds-Averaged Navier–Stokes equations (URANS) are solved with realizable k–ε turbulence model using the CFD code FLUENT. The impeller is redesigned with the same outlet diameter as the baseline pump. A two-step-form LEHD is recommended to suppress flow separation and secondary flow encountered in the baseline impeller in order to improve the efficiency. The splitter blades are added to improve the hydraulic performance and to reduce unsteady radial forces. The original double volute is substituted by a newly designed single volute one. The hydraulic efficiency of the centrifugal pump based on redesigned impeller with splitter blades and newly designed single volute is about 89.2%, a 3.2% higher than the baseline pump. The pressure fluctuation in the volute is significantly reduced, and the mean and maximum values of unsteady radial force are only 30% and 26.5% of the values for the baseline pump.

11 August 2020 in Energies
Verified
Journal Article
Open access
PDF file
Bin HuangBin Huang
Bin Huang
KPKexin Pu
Kexin Pu
PWPeng Wu
Peng Wu
Dazhuan WuDazhuan Wu
Dazhuan Wu
JLJianxing Leng
Jianxing Leng
In the seawater desalination system, the energy recovery system is a crucial part, as it consumes a lot of energy and plays a guiding role in the recovery efficiency. Therefore, in the energy recovery system, the recovery rate and energy consumption are the key factors to guide the system design. In order to make the energy recovery device achieve a high recovery rate under conditions of low energy consumption, the design and selection of each device in the system are particularly important. At the current stage, system matching optimization, device design optimization, and function objective optimization are widely used to improve the energy recovery system. In this paper, the design principle of the energy recovery integration system is analyzed, methods of reducing energy consumption and improving recovery efficiency are presented. The study provides guidance for the design and selection of energy recovery devices under different operating conditions.

1 June 2015 in Journal of Hydraulic Engineering
Verified
Journal Article
Closed access
Dazhuan WuDazhuan Wu
Dazhuan Wu
SYShuai Yang
Shuai Yang
PWPeng Wu
Peng Wu
LWLeqin Wang
Leqin Wang
A one-dimensional (1D) system and three-dimensional (3D) component cosimulation method based on the method of characteristic (MOC) and computational fluid dynamics (CFD) was proposed to study the interaction between valve-induced water hammer and pump during the rapid closing of the valve. In a long pipeline system, the pump was treated as a 3D CFD model using Fluent code, whereas the remaining system models (e.g., pipe, valve) were represented by 1D components using MOC. The numerical coupling and integration of both models were realized by a coupled code written using Visual Basic. The coupling theory and procedure were described in detail. MOC-CFD steady coupling in the case of the fully open state of the valve was first conducted. The corresponding results showed that the steady cosimulation can accurately determine the operating conditions. A transient cosimulation for the rapid closing procedure of the valve was conducted to study the interaction. The relative dynamic behavior obtained by MOC-CFD cosimulation was compared with that using MOC calculation alone. Transient simulation demonstrated that MOC-CFD coupling analysis was closer to real conditions because of considering the effect of fluid inertia. The effect was further explained through a comparison of internal and external characteristics between the transient and quasi-steady assumptions.

1 October 2015 in Journal of Fluids Engineering
Verified
Journal Article
Closed access
PDF file
Dazhuan WuDazhuan Wu
Dazhuan Wu
PYPeng Yan
Peng Yan
XCXin Chen
Xin Chen
PWPeng Wu
Peng Wu
SYShuai Yang
Shuai Yang
Modern pumps are designed to guarantee a sufficiently large operating range or to satisfy the performance requirements relative to more than one operating point. This study applies trailing-edge (TE) modification method based on TE rounding in the suction surface to widen the operating range of a mixed-flow pump. The effects of TE modification on the performance and internal flow of the mixed-flow pump are investigated through computational fluid dynamics (CFD) analysis. Local Euler head distribution is introduced to reveal the pattern of energy growth along the blade-aligned (BA) streamwise location. A pump model with TE modification is tested, and numerical results agree well with experimental data. The results show that TE modification significantly improves pump efficiency in the high flow rate region by more than 10%. The best pattern of normalized local Euler head distribution (NLEHD) is a convex curve of nearly constant growth rate. The overall heads are also improved, and the flow near the exit of the impeller exhibits better uniformity. This finding demonstrates that a small change in the TE of the impeller can influence flow structure in most areas of impeller channels and that the local Euler head distribution is closely related to pump efficiency. TE modification can effectively improve the performance of the mixed-flow pump with high flow rate.

2 July 2021 in Journal of Fluids Engineering
Verified
Journal Article
Closed access
PDF file
CWChengshuo Wu
Chengshuo Wu
WZWenqi Zhang
Wenqi Zhang
PWPeng Wu
Peng Wu
JYJiale Yi
Jiale Yi
HYHaojie Ye
Haojie Ye
Dazhuan WuDazhuan Wu
Dazhuan Wu
In this paper, the effects of modifying the blade pressure side (PS) on unsteady pressure pulsation and flow structures in a low specific speed centrifugal pump are carried out by experimental and computational fluid dynamics (CFD). Seven monitor points are arranged in the circumferential direction of the impeller outlet to capture the pressure signals in the volute at flow rate of 0.2–1.6Qd. Results show that the blade PS modification introduced here can significantly alleviate the amplitude of pressure pulsation at blade passing frequency (fBPF) in all concerned operation conditions. To study the effects of blade modification on the internal flow field, the volute domain is replaced by an even outlet region for CFD analysis. The shear stress transfer (SST) turbulence model is adopted for steady-state numerical simulation while the delayed detached eddy simulation (DDES) based on the SST approach is adopted for transient simulation. Results show that local unsteady velocity fluctuation is the dominant reason for pressure pulsation in the volute. After blade PS modification, the relative velocity distribution at the impeller outlet is more uniform and the intensity of shedding vortex at the blade trailing edge (TE) decreases significantly. The change of internal flow structure improves the uniformity of circumferential velocity distribution the downstream of the impeller outlet, which leads to the decrease of pressure fluctuation amplitude in the volute. Meanwhile, the local Euler head (LEH) distribution at the impeller outlet and the blade loading of PS are presented and compared. It can be concluded that the reduction of pressure pulsation attributes to a more uniform energy distribution at the impeller outlet which is achieved by actively unloading the PS of the modified blades.