This study investigates water-sand bursting disasters associated with fractured rock that affect safe mining in the mining areas of Western China. A broken rock water-sand seepage rheological test device was developed, and rheological tests were conducted on multiple groups of broken rock samples with single-stage axial loading and different load levels. When the rheology of each group of broken rock samples was stable, water-sand mixed fluid was injected into the samples at a certain pressure gradient to conduct water-sand seepage tests on broken rock masses. It was found that when the porosity of a fractured rock mass is within a certain range, the water-sand mixed fluid does not completely pass through the fractured rock mass and some sand particles are filtered by the fractured rock sample. There is an exponential relationship between the sand breaking ability and the sand filtration ability of fractured rock and its initial porosity, and the permeability of fractured rock decreases by a certain extent after sand filtration. However, for different load levels, when the flow through a fractured rock mass tends to be stable, the final porosity of the fractured rock mass decreases exponentially with axial compression. Based on the classical Kelvin rheological model and the basic theory of fractional calculus, a new fractional rheological model has been proposed and the rheological parameters under different load levels were fitted to the model. The new fractional rheological model is better able to describe the rheological characteristics of broken mudstone.
Reinforcement corrosion poses a great threat to the safety of reinforced concrete structures, and the fiber-reinforced polymer is the ideal material to partially replace steel bars due to the high strength, light weight and good durability. However, the selection of appropriate fiber materials and a reasonable ratio of fiber bar to steel bar is not clear. Here, we measured the mechanical properties of fiber bars containing aramid fiber and carbon fiber. The deflection deformation, crack distribution and maximum crack width of the concrete upon various loads were experimentally and theoretically investigated. The predictions of the maximum crack width and deflection of reinforced concrete beams under various loads were proposed in ACI standard, which may provide guidance for further applications of fiber-belt-bar-containing concrete beams.
Controlling the large deformation caused by bed separation failure of thick and soft surrounding rock in gob-side entry retaining is difficult. The deformation and failure modes of thick and soft surrounding rock are summarized and classified based on field research, theoretical analysis, laboratory tests, and actual measurements. Systematic research is conducted on the lithologic characteristics, failure characteristics, and control methods of the surrounding rock. The research findings are as follows: (1) The low strength, softening, and water swelling of thick mudstone, as well as its cataclasis, dilatancy, and long-term creep under strong mining and high stress are the objective reasons for large deformation of the surrounding rock. (2) Due to the weak stability of the surrounding rock-support structure and low collaborative roof side bearing capacity, no complete supporting structure is formed with the supporting system, causing the support body in each area to be crushed one by one, which is the subjective reason for the deformation and failure of the surrounding rock. (3) The deformation and failure characteristics of thick and soft surrounding rock in gob-side entry retaining are primarily divided into eight types: roof bending and sinking type, roof cutting along filling body, rib spalling type, roof fall type, filling body rotation type, filling body crushing type, roof step type, and roof cutting along the coal side. The initial points and key points for a chain reaction of each failure type are determined. (4) The surrounding rock is divided into 10 support zones at four levels, and control technology for “zonal support and overall reinforcement” is put forward. The mechanical effect of the support body in each zone and its role in maintaining the stability of surrounding rock are analyzed. This technology can ensure the integrity of the surrounding rock structure and improve the roof side collaborative bearing capacity.
It is one of the important safety problems in the process of mining shallow coal seams in western China that the rock mass affected by mining stress breaks and forms a penetrating fracture, leading to a sand burst in the working face. The self‐developed test system is used to carry out the experimental study on the flow characteristics of Aeolian sand in fractures. The research work is focused on the influence of several parameters, such as the thickness of the Aeolian sand layer, the fracture opening, and the fracture dip angle on the velocity of sand particles in fractures. The results show the following: (1) The influence of fracture opening and fracture angle on sand burst rate is much greater than that of sand thickness. No matter what the fracture angle and fracture opening value are, the influence weight of sand thickness on sand burst rate is almost zero. (2) When other conditions are unchanged, with the increase of fracture dip angle, the sand burst rate increases significantly, and the relationship between the sand burst rate and the fracture dip angle is exponential. (3) The influence weight of fracture opening is the largest. With the increase of fracture opening, the sand burst rate increases logarithmically. Finally, according to the test results, the relation equation which can simultaneously describe the influence of fracture opening and fracture inclination on the rate of the sand burst is fitted. This study can provide a theoretical basis and scientific guidance for the prevention and control of coal mine sand inrush disasters caused by roof cracking in western coal mines.
Fiber materials have advantages such as light weight and high strength, corrosion resistance, fatigue resistance, and easy processing and production, and they are widely applied in the repair and renovation of concrete structures. To promote the construction convenience of fiber materials, fiber raw yarn is continuously braided to form fiber-belt-bars. Based on the existing research, the performance of bonding between fiber-belt-bars and a concrete interface was investigated, and pull-out tests were performed to systematically investigate the effects of the fiber-belt-bar cross-sectional size, anchorage length, concrete strength, and fiber type on the bonding performance. The experimental results show that the bond strength reduces with an increase in the anchorage length, increase in cross-sectional size, and decrease in concrete strength, and the effect of fiber type on the bond strength is not obvious. On this basis, a formula for calculating the average bond strength of fiber-belt-bars is proposed. Experiments and calculations determined that the average bond strength between fiber-belt-bar and concrete with a cross-sectional size of 12 mm × 3 mm is 10–30% higher than that with a cross-sectional size of 20 mm × 3 mm for the same anchorage length. Finally, the minimum anchorage length of the fiber-belt-bar is proposed to provide a valuable reference for the use of fiber-belt-bar in concrete projects.