The purpose of this study was to investigate the effect of polypropylene fiber reinforced self-compacting concrete (SCC) at both the fresh and hardened stages, as well as their durability behavior. Properties of marble powder-based fiber reinforced SCC at fresh state were studied by means of slump flow diameter and flow time, V-funnel, and L-box test. The concrete properties at the hardened state were examined regarding compressive strength, split tensile strength, and flexural strength. Cement was replaced with marble powder with a substituting ratio of 4%, 8%, 12%, and 16% while polypropylene fibers were added as 0.1%, 0.2%, 0.3%, and 0.4%. The durability properties were analysed in the form of water permeability and chloride migration. In accordance with the outcomes of the tests, the workability of SCC deteriorated with an increase in fiber content, although it performed effectively at higher marble dosages. There was little impact of fibers on compressive strength and water permeability property of SCC. However, by adding the fibers in SCC improved both the split tensile strength and flexural strength by 16.92% and 11.36%, respectively. The addition of marble powder showed a synergetic effect with polypropylene fibers, which showed its applicability in SCC. The chloride resistance was improved at lower content of polypropylene fiber addition. For optimizing polypropylene fibers (pp) and marble powder substitution, the polynomial work expectation justifies the response surface technique (RSM). When a value of 0.05 is used to analyse the variation in the (Linear-ANOVA), the model is considered statistically significant. Performance of concrete was greatly enhanced by substituting 12% marble powder with cement and adding 3% polypropylene fiber.
22 September 2021 in Advances in Structural Engineering
This paper presents an experimental study on shear strengthening of reinforced concrete (RC) deep beams using externally applied carbon fiber reinforced polymer (CFRP) jackets. A total of 18 RC deep beams were tested using a four-point bending load. The examined parameter included span to depth ratio with or without CFRP strengthening. CFRP strips were applied perpendicular to the probable crack pattern as observed during testing for un-strengthened beams. The properties that is cracking behavior, ultimate strength, deflection, and energy dissipation capacity of beams were evaluated and discussed. The test results showed enhancement in shear strength up to 17% with CFRP. An increase in depth of RC deep beams caused a decrease in the rate of enhancement in shear strength for CFRP strengthened beams as compared to that observed in their counterparts. The experimental test results were compared with the existing design guidelines to assess their application for RC deep beams strengthened with CFRP. A strength equation based on regression analysis was developed to predict the experimental shear strength of RC deep beams strengthened with CFRP. This study showed that the RC deep beams strengthened with CFRP can effectively be used in structural engineering applications with enhanced shear strength and energy absorption capacity.
This article provides a concise overview of the modification mechanism of silver nanoparticles-functionalized multiwalled carbon nanotube (Ag-PM-WCNT), ground granulated blast furnace slag (GGBFS), and carbon quantum dots (CQD) on the mechanical and reliability properties of structural geopolymer reinforced-composite beams (GR-CBs). The structural GR-CBs were prepared with a geopolymer binder which included sodium carbonate and hydrated lime, GGBFS, Ag-PM-WCNT, and CQD, as well as the SP. A number of features were tested at 7, 28, 90, 180, 365, 2185, and 4370 days, including, compactness, porosity, shear, bending, and compressive strengths, Young’s modulus, and SEM analysis, as well as fluidity of fresh state of GR-CBs. The outcomes indicate that the incorporation of 0.5–0.7 wt% Ag‒PM‒WCNT and 2.5 wt% CQD leads to a decrease in fluidity and porosity while concurrently increasing the shear, bending, and compressive strengths by more than 104%, 160%, and 180%, respectively. The most remarkable shear, bending, and compressive strengths were observed in GR-CB11, measuring 9.5 MPa, 10.6 MPa, and 75 MPa respectively, after 4370 days. The Young’s modulus of the GR-CB, which includes Ag‒PM‒WCNT, GGBFS, and CQD, demonstrated a significant enhancement, alongside a remarkable level of densification within the microstructure and a variety of constitutive mathematical models. Therefore, developed GR-CB has the potential to facilitate practical implementation in real-world structure projects and infrastructure renewal.
This research aims to conduct a comparative analysis of the first crack load, flexural strength, and shear strength in reinforced concrete beams without stirrups. The comparison is made between the conventional model developed according to the current design code (ACI building code) and an unconventional approach using Artificial Neural Networks (ANNs). To accomplish this, a dataset comprising 110 samples of reinforced concrete beams without stirrup reinforcement was collected and utilised to train a Multilayer Backpropagation Neural Network in MATLAB. The primary objective of this work is to establish a knowledge-based structural analysis model capable of accurately predicting the responses of reinforced concrete structures. The coefficient of determination obtained from this comparison yields values of 0.9404 for the first cracking load, 0.9756 for flexural strength, and 0.9787 for shear strength. Through an assessment of the coefficient of determination and linear regression coefficients, it becomes evident that the ANN model produces results that closely align with those obtained from the conventional model. This demonstrates the ANN’s potential for precise prediction of the structural behaviour of reinforced concrete beams.
This paper presents the combined effect of polypropylene fibres (PPF), silica fume (SF), and fly ash (FA) on the characteristics of normal strength self-compacting concrete (NSSCC). NSSCC is proposed to be prepared by several combinations of PPF and class C FA as partial replacement of cement. NSSCC was prepared by incorporation of SF at 10% and PPF at 0.5%, 1%, and 1.5% by mass of Portland cement. Cohesion and adhesion properties of concrete become much better, along with increased tightness and excellent deformability due to the binding strength of PPF. These fibres inhibit the formation of pores in the concrete matrix and prevent the crack formation and its spread along with the matrix. The chloride migration coefficient was determined in accordance with NT Build 492. Mass diffusivity of chloride ions reduces with increasing concentrations of fly ash in concrete. Results indicate that fibre-reinforced concrete has the improved durability compared to other methods.