Mônica Castoldi Borlini Gadioli

Dr. Mônica Castoldi Borlini Gadioli

Mineral Technology Center - CETEM, Rio de Janeiro, Brazil
orcid

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 May 2022 in Sustainability
Verified
Journal Article
Open access
PDF file
CACarlos Paulino Agrizzi
Carlos Paulino Agrizzi
ECElaine Aparecida Santos Carvalho
Elaine Aparecida Santos Carvalho
MGMônica Castoldi Borlini Gadioli
Mônica Castoldi Borlini Gadioli
GBGABRIELA NUNES SALES BARRETO
GABRIELA NUNES SALES BARRETO
AAAfonso Azevedo
Afonso Azevedo
CVCarlos Maurício Fontes Vieira
Carlos Maurício Fontes Vieira
The development of artificial stone from the agglutination of polymeric resin using industrial wastes can be a viable alternative from a technical, economic, and sustainable point of view. The main objective of the present work was to evaluate the physical, mechanical, and structural properties of artificial stones based on quartzite waste added into a synthetic, epoxy, or biodegradable polyurethane polymer matrix. Artificial stone plates were produced through the vacuum vibration and compression method, using 85 wt% of quartzite waste. The material was manufactured under the following conditions: 3 MPa compaction pressure and 90 and 80 °C curing temperature. The samples were characterized to evaluate physical and mechanical parameters and microstructure properties. As a result, the artificial stone plates developed obtained ≤0.16% water absorption, ≤0.38% porosity, and 26.96 and 10.7 MPa flexural strength (epoxy and polyurethane resin, respectively). A wear test established both artificial quartzite stone with epoxy resin (AS-EP) and vegetable polyurethane resin (AS-PU) high traffic materials. Hard body impact resistance classified AS-EP as a low height material and AS-PU as a very high height material. The petrographic slides analysis revealed that AS-EP has the best load distribution. We concluded the feasibility of manufacturing artificial stone, which would minimize the environmental impacts that would be caused by this waste disposal. We concluded that the production of artificial rock shows the potential and that it also helps to reduce environmental impacts.

16 August 2022 in Materials
Verified
Journal Article
Open access
PDF file
MGMônica Castoldi Borlini Gadioli
Mônica Castoldi Borlini Gadioli
MAMariane Costalonga de Aguiar
Mariane Costalonga de Aguiar
FVFrancisco Wilson Hollanda Vidal
Francisco Wilson Hollanda Vidal
Maria Angelica Kramer Sant’AnaMaria Angelica Kramer Sant’Ana
Maria Angelica Kramer Sant’Ana
Kayrone Marvila de AlmeidaKayrone Marvila de Almeida
Kayrone Marvila de Almeida
AGAna Júlia Nali Giori
Ana Júlia Nali Giori
Brazil is one of the largest producers of ornamental stones in the world. The state of Espírito Santo has considerable social and economic relevance in the production of ornamental stones, particularly in exportation and the jobs that are directly related to this industry. The objectives of this work were to evaluate the effect of the incorporation of ornamental stone waste on the physical and mechanical properties of red ceramic manufactured using clays and waste from the state of Espírito Santo, and to collaborate to regulate the use of this ornamental stone waste in the ceramic industry when manufacturing products. Ornamental stone wastes were incorporated into the ceramic mass in the following proportions: 0, 10, 20, 30, 40 and 50% by weight. In the elaborated compositions, specimens were prepared by extrusion and were fired at 1050 °C and 1100 °C. After firing, the physical and mechanical properties of the material were analyzed using density, water absorption, porosity, linear shrinkage and mechanical strength. The results indicated an improvement in the properties of the ceramics with the addition of the waste by mass for the two temperatures. Therefore, the lower temperature (1050 °C) can be used to sinter the materials produced whilst obtaining satisfactory results and saving electrical energy. Ornamental stone waste has very promising applications in the ceramic industry.

18 August 2023 in Journal of Building Engineering
Verified
Journal Article
Closed access
MGMônica Castoldi Borlini Gadioli
Mônica Castoldi Borlini Gadioli
CACarlos Paulino Agrizzi
Carlos Paulino Agrizzi
MAMariane Costalonga de Aguiar
Mariane Costalonga de Aguiar
RLRondinelli M. Lima
Rondinelli M. Lima
APAlan D. Pedruzzi
Alan D. Pedruzzi
CRCarlos E.G. Ribeiro
Carlos E.G. Ribeiro

9 October 2022 in Sustainability
Verified
Journal Article
Open access
PDF file
MAMariane Costalonga de Aguiar
Mariane Costalonga de Aguiar
MGMônica Castoldi Borlini Gadioli
Mônica Castoldi Borlini Gadioli
Maria Angelica Kramer Sant’AnaMaria Angelica Kramer Sant’Ana
Maria Angelica Kramer Sant’Ana
Kayrone Marvila de AlmeidaKayrone Marvila de Almeida
Kayrone Marvila de Almeida
FVFrancisco Wilson Hollanda Vidal
Francisco Wilson Hollanda Vidal
CVCarlos Maurício Fontes Vieira
Carlos Maurício Fontes Vieira
The ornamental stone industry is growing and has a large production in Brazil, mainly in Espírito Santo, where the largest production in the country is concentrated. Brazil is part of the group of countries that produce the most ornamental stones in the world; however, the generation of waste in this sector is very large. These ornamental stone wastes when used for the manufacture of new materials, such as red ceramics, contribute to the reduction in the raw material clay and to the reduction in the environmental impact. The objective of this work was to incorporate fine wastes from the processing of ornamental stones called FIBRO in red ceramics and later, to contribute to the standardization of the use of these wastes in the ceramic industry, contributing to the manufacture of more economical and sustainable products. Wastes were incorporated in the proportion of 0 to 50% by mass that were prepared by extrusion and fired at 900 °C, 950 °C, and 1000 °C. After firing, the physical and mechanical properties of the ceramic material were evaluated. Specific mass apparent, water absorption, porosity, and flexural strength by three points tests were carried out. The results showed that from 30% at the lowest temperature, tile is already fabricated within the values stipulated by the standards, thus saving energy. The analyzed waste is a material with excellent chemical characteristics to be used in the ceramic mass, in addition to having improved the technological properties of the material, such as less water absorption and greater flexural strength.

27 December 2023 in Sustainability
Verified
Journal Article
Open access
PDF file
MAMariane Costalonga de Aguiar
Mariane Costalonga de Aguiar
MFMaria Carolyna Sopeletti Fernandes
Maria Carolyna Sopeletti Fernandes
Maria Angelica Kramer Sant’AnaMaria Angelica Kramer Sant’Ana
Maria Angelica Kramer Sant’Ana
VSViviana Possamai Della Sagrillo
Viviana Possamai Della Sagrillo
AAAlexandre dos santos Anastácio
Alexandre dos santos Anastácio
MGMônica Castoldi Borlini Gadioli
Mônica Castoldi Borlini Gadioli
The ornamental stone industry plays a crucial role in the world economy, and thus the production process of ornamental stones generates a large volume of waste that is normally destined for landfills. Given the growing market import of artificial stones, there is a need for more sustainable practices to reduce waste and improve the use of natural resources. Thus, the present study aims to develop artificial stones with waste from the ornamental stone extraction process from the quarry, and vegetable polyurethane resin derived from castor oil, in order to analyze its viability in the production of artificial stone slabs. The wastes used in this work were three quartzites, fragmented and mixed with three grain sizes, called coarse, medium, and fine. These wastes were characterized using X-ray fluorescence (XRF), X-ray diffraction (XRD), Fourier transform infrared (FTIR), and thermal analysis (TGA/DTG/DSC). Artificial stone slabs were produced using 15 wt.% vegetable polyurethane resin derived from castor oil and 85 wt.% ornamental stone wastes (quartzite). These slabs underwent apparent density, water absorption, porosity, 3-point flexural strength, scanning electron microscopy (SEM), petrography, and X-ray diffraction (XRD) tests. According to the results obtained, it was possible to prove the technical viability of manufacturing artificial stones with ornamental stone wastes and with the use of vegetable polyurethane resin derived from castor oil. The use of these raw materials not only resulted in the manufacture of a new material but also in an environmentally conscious and sustainable approach, following precepts such as the circular economy. The creation of these eco-efficient products is a significant contribution to the search for solutions that value environmental preservation and the optimization of natural resources.

29 January 2013 in HOLOS
Verified
Journal Article
Open access
PDF file
MBMichelle Pereira Babisk
Michelle Pereira Babisk
FVFrancisco Wilson Hollanda Vidal
Francisco Wilson Hollanda Vidal
WRWagner Souza Ribeiro
Wagner Souza Ribeiro
MAMariane Costalonga de Aguiar
Mariane Costalonga de Aguiar
MGMônica Castoldi Borlini Gadioli
Mônica Castoldi Borlini Gadioli
CVCarlos Maurício Fontes Vieira
Carlos Maurício Fontes Vieira
A incorporação de resíduos industriais em cerâmica vermelha vem sendo muito utilizada atualmente na busca de matérias-primas alternativas, e também buscando uma destinação ambientalmente correta aos resíduos. Durante os processos de beneficiamento das rochas ornamentais, há perdas significativas de material e geração de resíduos, os quais muitas vezes são dispostos de forma inadequada na natureza, sem previsão de utilização ou reuso. A indústria de extração e beneficiamento de quartzito do município de Várzea, região de Seridó, na Paraíba, gera cerca de 20 mil kg de resíduos por dia. O quartzito é classificado geologicamente como uma rocha metamórfica, composto quase que inteiramente de grãos de quartzo. O objetivo desse trabalho é caracterizar e avaliar os efeitos da incorporação do resíduo de quartzito em cerâmica vermelha. Foram estudadas incorporações de até 40% em peso de resíduo em massa cerâmica, preparados corpos de prova retangulares por prensagem uniaxial a 20 MPa e queimados a 800ºC. A caracterização das matérias primas foi realizada por meio de análise química por fluorescência de raios-X e análise de fases cristalinas por difração de raios-X. As propriedades físicas e mecânicas determinadas de interesse para a cerâmica vermelha foram: densidade aparente, absorção de água, retração linear e tensão de ruptura à flexão. A microestrutura foi avaliada por microscopia eletrônica de varredura. Os resultados indicaram que o resíduo de quartzito é um material com potencial para ser utilizado como componente na massa de cerâmica vermelha.