The success of fuel cells depends on the proper design of the electrodes and membrane allowing easy access of oxygen and protons. Using non-precious catalyst electrodes based on recyclable carbon nanostructures is most important to produce clean energy and increase the ability to commercialize the fuel cells. Herein, reduced graphene oxide (rGO) and graphene/magnetic iron oxide nanocomposite (rGO/MIO) are successfully synthesized as anode and cathode, respectively, from polyethylene terephthalate (PET) waste bottles using easy steps in order to simplify the method and reducing the production cost. While, the membrane is prepared from low cost and eco-friendly ternary polymers blend which are polyvinyl alcohol (PVA), polyethylene oxide (PEO) and polyvinyl pyrrolidone (PVP) then doped with sulfonated graphene oxide. The prepared electrodes have characteristic high porosity and their electrocatalytic performances are evaluated using three-electrode cell electrochemical studies as cyclic voltammetry and linear scan voltammetry combined with rotating disk electrode. A new assembly of the membrane between two non-precious catalyst electrodes as a single polymer electrolyte membrane fuel cell (PEMFC) was developed using a catalyst-coated membrane technique. The membrane electrode assembly (MEA) design parameters which affect its performance in hydrogen fuel cells as number of used catalyst layers (CL) or using gas diffusion layer (GDL) were evaluated in a single cell set-up with H2/O2 operation and the results revealed that the performance MEA was enhanced with using GDL more than that of MEA without GDL by 66% at a current density of 0.8 A cm−2 while the performance with double CL was better than that of the conventional single CL by 30% at a current density of 0.98 mA cm−2.
Effective and efficient removal of both heavy metal pollutants and bacterial contamination from fresh water is an open issue, especially in developing countries. In this work, a novel eco-friendly functional composite for water treatment application was investigated. The composite consisted of electrospun nanofiber membrane from blended polyvinyl alcohol (PVA)/iota carrageenan (IC) polymers doped with equal concentrations of graphene oxide (GO) nanoparticles and polyaniline (PANI). The effectiveness of this composite as a water purification fixed-bed filter was optimized in a batch system for the removal of cadmium (Cd+2) and lead (Pb+2) ions, and additionally characterized for its antimicrobial and antifungal properties and cytotoxicity effect. The fiber nanocomposite exhibited efficient antibacterial activity, with maximum adsorption capacity of about 459 mg g−1 after 120 min for Cd+2 and of about 486 mg g−1 after 90 min for Pb+2. The optimized conditions for removal of both metals were assessed by using a response surface methodology model. The resulting scores at 25 °C were 91.4% (Cd+2) removal at 117 min contact time for 89.5 mg L−1 of initial concentration and 29.6 cm2 membrane area, and 97.19% (Pb+2) removal at contact time 105 min for 83.2 mg L−1 of initial concentration and 30.9 cm2 nanofiber composite membrane. Adsorption kinetics and isotherm followed a pseudo-second-order model and Langmuir and Freundlich isotherm model, respectively. The prepared membrane appears to be promising for possible use in domestic water purification systems.
1 February 2010 in International Journal of Electrochemical Science
In our daily lives and product manufacturing, metal corrosion causes significant economic losses. Numerous polymeric composite coatings have been shown to be resistant to harsh environments, such as those found in marine environments. In this study, a composite of polyvinyl alcohol/polyaniline blend loaded with carboxylated graphene was explored in the search for long-lasting coatings to resist electrochemical deterioration of cast iron in desalination systems of saltwater. Polyvinyl alcohol/polyaniline/carboxylated graphene oxide nanocomposite was spin-coated onto cast iron samples. Electrochemical impedance spectroscopy (EIS) and electrochemical DC corrosion testing with a three-electrode system were used to study corrosion resistance in uncoated and coated cast iron samples. The results exhibit effective corrosion protection properties. The EIS data indicated better capacitance and higher impedance values for coated samples than bare metal, depicting enhanced corrosion resistance against the saline environment. Tafel analysis confirmed a significant decrease in the corrosion rate of the PVA/PANI/GO-COOH coated sample.
Direct liquid fuel cells represent one of the most rapidly emerging energy conversion devices. The main challenge in developing fuel cell devices is finding low-cost and highly active catalysts. In this work, PET bottle waste was transformed into nitrogen-doped graphene (NG) as valuable catalyst support. NG was prepared by a one-pot thermal decomposition process of mineral water waste bottles with urea at 800 °C. Then, NG/Pt electrocatalysts with Pt loadings as low as 0.9 wt.% and 1.8 wt.% were prepared via a simple reduction method in aqueous solution at room temperature. The physical and electrochemical properties of the NG/Pt electrocatalysts are characterized and evaluated for application in direct borohydride peroxide fuel cells (DBPFCs). The results show that NG/Pt catalysts display catalytic activity for borohydride oxidation reaction, particularly the NG/Pt_1, with a number of exchanged electrons of 2.7. Using NG/Pt composite in fuel cells is anticipated to lower prices and boost the usage of electrochemical energy devices. A DBPFC fuel cell using NG/Pt_1 catalyst (1.8 wt.% Pt) in the anode achieved a power density of 75 mW cm−2 at 45 °C. The exceptional performance and economic viability become even more evident when expressed as mass-specific power density, reaching a value as high as 15.8 W mgPt−1.
Methylene blue (MB) immobilized onto a sulfonated poly(glycidyl methacrylate) (SPGMA) polymer composite has been developed as a novel adsorbent for water treatment applications. The MB adsorptions onto sulfonated poly(glycidyl methacrylate) polymer characters have been studied. The adsorption isotherms, namely Langmuir and Freundlich, have been investigated. Other isotherm models. As a compromise between the Freundlich and Langmuir isotherm models, such as the D–R isotherm and the Temkin isotherm, have been compared. The results indicated that the adsorption process followed the Freundlich isotherm model, indicating heterogeneous surface site energies and multi-layer levels of sorption. This study selected three linear kinetic models, namely pseudo-first order, pseudo-second order, and Elovich, to describe the MB sorption process using SPGMA negatively charged nanoparticles (430 nm). The obtained data revealed that the adsorption process obeyed the pseudo-second-order kinetic model, suggesting that the rate-limiting step in these sorption processes may be chemisorption. Furthermore, the thermodynamic parameters have been evaluated. Moreover, the interaction of the MB molecules with SPGMA nanoparticles has been simulated using the governing equation that describes ion exchange resin derived from Nernst—Plank equations between two ion species. Finally, the developed MB-SPGMA composite adsorbent (27 mg/g) wastested for the first time for the removal of Cr6+ ions and Mn7+ metal ions from dichromate and permanganate-contaminated waters under mild adsorption conditions, opening a new field of multiuse of the same adsorbent in the removal of more than one contaminant.