A low-cost, wideband PCB manufactured antenna is proposed in this letter for 5G/6G antenna-in-package (AiP) applications with wideband common-mode current (surface-wave) choking characteristics. The antenna is based on a grounded, wideband, high-efficiency electromagnetic structure (WHEMS) and a backing cavity, through both of which a radiating choke is introduced. By changing the choking condition of a quarter wave length widely applied in traditional low frequency baluns, wideband common-mode current suppression is achieved. The enclosing wall of the backing cavity is realized by a combination of isolated grounded vias and connected grounded vias based on current polarizations on the wall. Finally, a 22% impedance bandwidth (60-75GHz), and a relative gain of 8-10 dBi within the band is achieved.
28 January 2019 in IEEE Transactions on Vehicular Technology
A compact wideband high gain directional antenna is proposed in this paper for marine communications. The antenna consists of a back plane (reflector), a slot-loop antenna (driven element), and a director of rod. Based on the current distribution, the slot-loop antenna is equivalent to an array of three linear current dipoles. The dipole acts as an element of the director, which provides a high efficient director for slot-loop antenna according to theoretical analysis. Both the impedance bandwidth and the 1 dB gain bandwidth are 45% covering 1.7–2.7 GHz in this design. A gain of 11.2 to 12.2 dBi is obtained in the working band with only one set of directors. The directors have a dimension less than the antenna aperture in the H-plane, which can be seen as one director in the end-fire direction. Compared with the classic Yagi antenna with the same gain level, the newly proposed antenna is only half of the size in radiation direction, which is a breakthrough for the Yagi antenna design. This size reduction can significantly minimize the interference between ship-borne antennas. The antenna is fabricated using only metal of low cost, which is useful for the ship-to-shore/ship communicating applications and desirable for the large-scale deployment.
27 February 2020 in IEEE Internet of Things Journal
A rugged linear array is proposed for covering both the LTE and 5G bands with an intermediate gain. The antenna is composed of a driven element, a set of directors, and a set of reflectors, where the excited element is a wideband high-efficiency electromagnetic structure (WHEMS) and the parasitic elements consist of metal rods. To achieve a rugged design, similar to the classic Yagi antenna, all of the elements should be conductively connected, so that it can be welded. The weldable mechanism is started on the driven radiating element. In addition, a balun is introduced in the antenna to reduce the influence of unbalanced common mode currents. A wind resistance analysis is also presented, where the drag force of the proposed antenna is approximately a quarter of that for an antenna with a metal plate. The antenna exhibits a gain of 10.8-13.3 dBi for a 78% fractional bandwidth (1.7-3.7 GHz), which is a 7-fold increase from that of the Yagi antenna, without sacrificing the gain or rugged design. The proposed antenna has the advantages of a simple feeding arrangement, low cost, light weight, low wind resistance, and rugged structure; and is suitable for all-weather large-scale Internet of Things (IoT) deployment at a rural site or in a harsh networking environment.
Frequency-modulated continuous wave (FMCW) radar is widely used in automotive and consumer electronics because of its range, velocity, and angle measurement functionality. In an FMCW radar system, the isolation between transmitting (Tx) and receiving (Rx) subsystems affects the sensitivity of the FMCW system, which directly impacts the system’s overall performance in target detection. The factors that affect system performance include transmitter-to-receiver on-chip coupling and Tx-to-Rx antenna coupling. The on-chip isolation performance is basically fixed once a radar chip is given, but the antenna isolation performance depends on a designed antenna array. Usually, a targeted antenna requirement is first specified, and then the corresponding Tx and Rx antenna array is designed. However, there is no general principle or criteria for specifying a proper antenna isolation requirement in the existing research. In this paper, first, we reveal that the antenna isolation requirement should be set to be almost the same as the given on-chip isolation value, which is very significant as a general guideline in setting a targeted antenna isolation requirement. All current antenna isolation methods cannot reach the level of on-chip isolation in a compactly designed radar system. We further propose a teardrop-based method to provide high antenna isolation. The principle of an antenna isolation requirement and a novel antenna design using teardrops are both analyzed and demonstrated based on a representative 24 GHz FMCW radar. Our teardrop-shaped structure in the mouth of the conventional Vivaldi antenna achieved greater than 50 dB isolation, while the distance between the Tx and Rx antennas could be reduced to 2.1 mm.
Human presence detection and water level detection are two essential functions of smart toilets, making smart toilets more intelligent and hygienic. Traditional solutions require different sensors for each of these functions. Furthermore, existing detection methods in smart toilets have some limitations, such as sensor size, the undesirable effect of environment on detection results, etc. Millimeter-wave (mmWave) radars offer better performance in terms of ranging accuracy and environmental stability. If mmWave radar is used to achieve the above two functions, the radar system is required to radiate toward the region of interest (RoI). The RoI for presence detection is the front of the toilet, while RoI for water level detection is the toilet bowl. Therefore, the radar needs to radiate signals forward and downward radiation simultaneously, which requires the radar to achieve an orthogonal bi-directional radiation. In this paper, we innovatively propose a low-cost radar system with orthogonal bidirectional radiation with good antenna gain and isolation performance by using Vivaldi antennas and wideband high efficiency electromagnetic structure (WHEMS) antennas. Additionally, appropriate antenna selection gives the antenna system the characteristics of wide bandwidth to match different toilet installation environments with higher reliability. The system can achieve presence detection and water level detection well, and has the advantages of low cost, small size and practical application value.
8 August 2022 in IEEE Open Journal of Antennas and Propagation
A broadband compact antenna is proposed in this paper with an enhanced broadside gain performances in the +/− z directions. A design method of complementary gains is presented to overcome the gain reduction caused by the cancellation of reverse currents in the middle of the band of interest, where a design equation of the excited element of the antenna is given. This objective is achieved by accurately analyzing the resonant modes of the two parallel connected antennas of the excited element in order to achieve an overall wideband radiator. An orthogonal radiating choke (ORC) is proposed to remove the gain depression due to the leakage of electromagnetic waves toward the upper portion of the band of interest through simultaneously enhancing the broadside gain and choking the end-fire travelling wave. Each one patch of the ORC acting as both a TM 10 mode microstrip antenna and a choke of end-fire travelling wave. With the help of the ORC, the gain in +/− z directions is enhanced by 13.1 dB at 6 GHz compared to that without the ORC. The proposed antenna presents a realized broadside gain of 2.1-7.8 dBi in the +/− z directions within a bandwidth of 158% (700 MHz – 6 GHz). Both the simulated and measured results demonstrate that the proposed antenna exhibits desirable bandwidth and gain characteristics and is a promising candidate for broadband integrated wireless systems.