Filip Votava

Dr. Filip Votava

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 January 2023 in Materials
Verified
Journal Article
Open access
PDF file
FVFilip Votava
Filip Votava
HJHana Jirková
Hana Jirková
LKLudmila Kučerová
Ludmila Kučerová
ŠJŠtěpán Jeníček
Štěpán Jeníček
Press-hardening, also known as hot stamping, is a manufacturing process for producing car body parts that must meet the high demands of their mechanical properties and safety parameters. Moreover, these components often require different mechanical properties in different parts of the component. This work presents the press-hardening process in a special combined tool where one half of the tool is heated and the other half is cooled. The cooled part has been 3D printed due to the complexity of the internal cooling channels. The aim of this work is to investigate the variation of the microstructures in the sheet metal and the mechanical properties in relation to the cooling process in the tool and to determine the transition area where these properties cross over. Two steels were chosen for the experiment. The most commonly used steel 22MnB5, and an experimental high-strength steel with 0.2% C alloyed with manganese and aluminium. A temperature of 425 °C was set in the heated part of the tool, and different holding times in the tool were tested. In the heated part of the tool, a bainitic structure with a fraction of ferrite and retained austenite was formed, while in the quenched part of the tool, a martensitic transformation was promoted due to rapid cooling. In addition to microscopic analyses, mechanical tests and hardness measurements were also performed.

13 November 2025 in Materials
Verified
Journal Article
Open access
PDF file
FVFilip Votava
Filip Votava
LKLudmila Kučerová
Ludmila Kučerová
ŠJŠtěpán Jeníček
Štěpán Jeníček
RLRadek Leták
Radek Leták
JHJiri Hajek
Jiri Hajek
ZNZbyšek Nový
Zbyšek Nový
In this study, sheets of experimental high-carbon low-density steels (LDSs) with a thickness of 1.7 mm were processed in a combined tool designed for press-hardening. Press hardening, also known as hot stamping or hot press forming, is a manufacturing process used to create car body parts with exceptional mechanical properties and safety standards. These components often require tailored properties, meaning different mechanical characteristics in various parts of the component. LDSs have a lower specific density than conventional steels, so their use would be particularly suitable in automotive applications. Combined tools achieve distinct mechanical properties within a single part through thermomechanical processing. Simultaneous forming and heat treatment create tailored zones of high strength and ductility within the sheet metal. The hardened zone provides crashworthiness, while the more ductile zone absorbs kinetic energy and converts it into deformation energy. Hot stamping enables forming complex geometries from high-strength sheets with limited cold formability, a capability that can also be exploited for the aluminium-alloyed LDS under investigation in this work. Three different high-carbon LDSs with differences in chemical composition were subjected to this experiment, and the hardness, microstructure, and mechanical properties of the two areas of each sheet were evaluated. The aim is to determine their suitability for processing by press hardening and to try to achieve tailored properties (i.e., differences in ductility and strength across one part) as in a typical representative of 22MnB5 boron steel, where a strength limit of 1500 MPa at 5% ductility is achieved in the cooled part and 600 MPa at 15% in the heated part. Tailored properties were also achieved in the investigated LDS, but with only relatively small differences between the two tool areas. The omega profiles were produced by press hardening without visible defects, and it was possible to process the steels without any difficulties.

1 November 2022 in Engineering Proceedings
Verified
Conference Paper
Open access
PDF file
FVFilip Votava
Filip Votava
JVJiří Vrtáček
Jiří Vrtáček
JSJindrich Sykora
Jindrich Sykora
MWMichal Weinar
Michal Weinar
HJHana Jirková
Hana Jirková
Press hardening is used to produce complex parts by hardening them in a die. This results in martensitic structures with high strength values but low ductility. However, for real components, the combination of places with high strength or high ductility is required. One possibility is using a combined tool (i.e., tailoring methods) instead of joining parts by welding or gluing. Therefore, this work was focused on the construction and design of a partly heated and partly cooled tool for press hardening. This makes it possible to process high-strength steels and achieve different mechanical properties at different points in the stamping. To achieve intensive cooling, part of the tool was made by 3D printing, making it possible to create effective cooling channels in the functional part of the tool. The second part of the tool was heated by heating cartridges. FEM in DEFORM software was used to lay out the heating cartridges and cooling channels. The tool was successfully installed on a hydraulic press, including the first tests to achieve omega profiles with different mechanical properties.

7 March 2025 in Materials
Verified
Journal Article
Open access
PDF file
RLRadek Leták
Radek Leták
LKLudmila Kučerová
Ludmila Kučerová
HJHana Jirková
Hana Jirková
ŠJŠtěpán Jeníček
Štěpán Jeníček
FVFilip Votava
Filip Votava
Solutions and new processes are continually being developed to produce components demonstrating high strength and elongation. This paper focuses on medium manganese steel with a composition of 0.2% carbon, 3% manganese, and 2.15% aluminium (by weight percent). The mechanical properties of the steel and the effect of aluminium and manganese on the microstructure are investigated. The steel sheets are shaped into omega profiles using a press tool, followed by the intercritical annealing of the samples to enhance their ductility. Before the experiment, the anticipated values were a tensile strength (UTS) of approximately 1100 MPa and elongation within 30–35%. A key objective was to achieve a microstructure that incorporates residual austenite. The experimental parameters were carefully derived from an extensive exploration to identify potential weaknesses in the experiment. The main parameters selected were the intercritical annealing (IA) temperature and IA dwell time. The results revealed that the highest recorded UTS was 1262 ± 6 MPa, while the maximum elongation achieved was 16 ± 1%.