Jiri Hajek

Dr. Jiri Hajek

COMTES FHT a.s.
orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 February 2021 in Metals
Verified
Journal Article
Open access
PDF file
JHJiri Hajek
Jiri Hajek
ZDZaneta Dlouha
Zaneta Dlouha
VPVojtěch Průcha
Vojtěch Průcha
This article is a response to the state of the art in monitoring the cooling capacity of quenching oils in industrial practice. Very often, a hardening shop requires a report with data on the cooling process for a particular quenching oil. However, the interpretation of the data can be rather difficult. The main goal of our work was to compare various criteria used for evaluating quenching oils. Those of which prove essential for operation in tempering plants would then be introduced into practice. Furthermore, the article describes monitoring the changes in the properties of a quenching oil used in a hardening shop, the effects of quenching oil temperature on its cooling capacity and the impact of the water content on certain cooling parameters of selected oils. Cooling curves were measured (including cooling rates and the time to reach relevant temperatures) according to ISO 9950. The hardening power of the oil and the area below the cooling rate curve as a function of temperature (amount of heat removed in the nose region of the Continuous cooling transformation - CCT curve) were calculated. V-values based on the work of Tamura, reflecting the steel type and its CCT curve, were calculated as well. All the data were compared against the hardness and microstructure on a section through a cylinder made of EN C35 steel cooled in the particular oil. Based on the results, criteria are recommended for assessing the suitability of a quenching oil for a specific steel grade and product size. The quenching oils used in the experiment were Houghto Quench C120, Paramo TK 22, Paramo TK 46, CS Noro MO 46 and Durixol W72.

30 March 2022 in Materials
Verified
Journal Article
Open access
PDF file
JHJiri Hajek
Jiri Hajek
ZNZbyšek Nový
Zbyšek Nový
LKLudmila Kučerová
Ludmila Kučerová
HJHana Jirková
Hana Jirková
PSPavel Salvetr
Pavel Salvetr
TBTereza Bystřická
Tereza Bystřická
This paper introduces a new alloying concept for low-density steels. Based on model calculations, samples—or “heats”—with 0.7 wt% C, 1.45 wt% Si, 2 wt% Cr, 0.5 wt% Ni, and an aluminium content varying from 5 to 7 wt% are prepared. The alloys are designed to obtain steel with reduced density and increased corrosion resistance suitable for products subjected to high dynamic stress during operation. Their density is in the range from 7.2 g cm−3 to 6.96 g cm−3. Basic thermophysical measurements are carried out on all the heats to determine the critical points of each phase transformation in the solid state, supported by metallographic analysis on SEM and LM or the EDS analysis of each phase. It is observed that even at very high austenitisation temperatures of 1100 °C, it is not possible to change the two-phase structure of ferrite and austenite. A substantial part of the austenite is transformed into martensite during cooling at 50 °C s−1. The carbide kappa phase is segregated at lower cooling rates (around 2.5 °C s−1).

13 November 2025 in Materials
Verified
Journal Article
Open access
PDF file
FVFilip Votava
Filip Votava
LKLudmila Kučerová
Ludmila Kučerová
ŠJŠtěpán Jeníček
Štěpán Jeníček
RLRadek Leták
Radek Leták
JHJiri Hajek
Jiri Hajek
ZNZbyšek Nový
Zbyšek Nový
In this study, sheets of experimental high-carbon low-density steels (LDSs) with a thickness of 1.7 mm were processed in a combined tool designed for press-hardening. Press hardening, also known as hot stamping or hot press forming, is a manufacturing process used to create car body parts with exceptional mechanical properties and safety standards. These components often require tailored properties, meaning different mechanical characteristics in various parts of the component. LDSs have a lower specific density than conventional steels, so their use would be particularly suitable in automotive applications. Combined tools achieve distinct mechanical properties within a single part through thermomechanical processing. Simultaneous forming and heat treatment create tailored zones of high strength and ductility within the sheet metal. The hardened zone provides crashworthiness, while the more ductile zone absorbs kinetic energy and converts it into deformation energy. Hot stamping enables forming complex geometries from high-strength sheets with limited cold formability, a capability that can also be exploited for the aluminium-alloyed LDS under investigation in this work. Three different high-carbon LDSs with differences in chemical composition were subjected to this experiment, and the hardness, microstructure, and mechanical properties of the two areas of each sheet were evaluated. The aim is to determine their suitability for processing by press hardening and to try to achieve tailored properties (i.e., differences in ductility and strength across one part) as in a typical representative of 22MnB5 boron steel, where a strength limit of 1500 MPa at 5% ductility is achieved in the cooled part and 600 MPa at 15% in the heated part. Tailored properties were also achieved in the investigated LDS, but with only relatively small differences between the two tool areas. The omega profiles were produced by press hardening without visible defects, and it was possible to process the steels without any difficulties.

19 May 2023 in Materials
Verified
Journal Article
Open access
PDF file
JHJiri Hajek
Jiri Hajek
ZNZbyšek Nový
Zbyšek Nový
LKLudmila Kučerová
Ludmila Kučerová
HJHana Jirková
Hana Jirková
ČDČrtomir Donik
Črtomir Donik
ZJZdeněk Jansa
Zdeněk Jansa
The paper presents the possibilities of heat treatment of low-density structural steels usable for springs. Heats have been prepared with chemical compositions 0.7 wt% C and 1 wt% C, as well as 7 wt% Al and 5 wt% Al. Samples were prepared from ingots weighing approximately 50 kg. These ingots were homogenised, then forged, and hot rolled. Primary transformation temperatures and specific gravity values were determined for these alloys. For low-density steels, there usually needs to be a solution to achieve the required ductility values. At cooling rates of 50 °C/s and 100 °C/s, the kappa phase is not present. A SEM analysed the fracture surfaces for the presence of transit carbides during tempering. The martensite start temperatures ranged from 55–131 °C, depending on the chemical composition. The densities of the measured alloys were 7.08 g/cm3 and 7.18 g/cm3, respectively. Therefore, heat treatment variation was carried out to achieve a tensile strength of over 2500 MPa, with ductility of almost 4%. Hardnesses above 60 HRC were achieved for 1 wt% C heats using the appropriate heat treatment.

1 August 2021 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
JHJiri Hajek
Jiri Hajek
VCV. Coufal
V. Coufal
Comparison is made between several thermochemical treatment methods, with focus on boronizing. Boronizing has the potential to become a substitute for chromium plating or nitriding (gas nitriding) in the arms industry. This experimental study explored the chemical composition, hardness, corrosion resistance, tribological properties and toughness of several surface layers and coatings. The experimental substrates were EN 32CrMoV12-10 and EN 31CrMoV9 steels. Boronizing is intended for the gas tube and piston of a specific firearm. In the boride layer, the hardness of 1900 HV0.1 was reached. In the chromium and nitrided layers, hardness was 1100 HV0.1. In these experiments, original rifle tubes and disc samples were used. The thicknesses were as follows: the chromium layer: up to 70 μam, boride layer: 100 μam and nitride layer: 290 μam. Wear properties were compared using the Pin-on-Disc wear test. Fracture toughness according to Palmquist was the highest in the nitride case and the lowest in the chromium layer. Across all the layers, the range was from 2.5 to 9.5 MN/m3/2. Some differences were found between the boride layer with post-process heat treatment and layers without heat treatment. As a result of the research, it was found that Boronizing of the gas tube proved a suitable substitute for hard chrome plating or nitriding.