Perovskite solar cells (PSCs) have drawn significant consideration as a competing solar cell technology because of the drastic advance in their power conversion efficiency (PCE) over the last two decades. The interfaces between the electron transport layer (ETL) and the absorber layer and between the absorber layer and the hole transport layer (HTL) have a major impact on the performance of the PSCs. In this paper, we have investigated the defect interfaces between ETL/absorber layer and absorber layer/HTL of calibrated experimental CH ₃ NH ₃ PbX ₃ lead-based and FASnI ₃ lead-free PSCs. The influence of the defect interfaces is studied in order to find the optimum value for the maximum possible PCE. While the PCE has not been enhanced considerably for the lead-based, it is boosted from 1.76% to 5.35% for lead-free PSCs. Also, bulk traps were found to have minor role in comparison with interface traps for the lead-free cell while they have a significant impact for the lead-based cell. The results presented in this work would shed some light on designing interface defects of various types of practical PSC structures and demonstrates the crucial impact of the interface defects on lead-free vs lead-based PSCs. All simulation studies are performed by using SCAPS-1D simulator.

In this work, we report on the effect of substituting the active intrinsic i-layer on a conventional pin structure of lead-free perovskite solar cell (PSC) by a homo p-n junction, keeping the thickness of the active layer constant. It is expected that when the active i-layer is substituted by a p-n homo junction, one can increase the collection efficiency of the photo-generated electrons and holes due to the built-in electric field of the homo junction. The impact of the technological and physical device parameters on the performance parameters of the solar cell have been worked out. It was found that p-side thickness must be wider than the n-side, while its acceptor concentration should be slightly lower than the donor concentration of the n-side to achieve maximum efficiency. In addition, different absorber types, namely, i-absorber, n-absorber and p-absorber, are compared to the proposed pn-absorber, showing a performance-boosting effect when using the latter. Moreover, the proposed structure is made without a hole transport layer (HTL) to avoid the organic issues of the HTL materials. The back metal work function, bulk trap density and ETL material are optimized for best performance of the HTL-free structure, giving J_sc = 26.48, V_oc = 0.948 V, FF = 77.20 and PCE = 19.37% for AM1.5 solar spectra. Such results highlight the prospective of the proposed structure and emphasize the importance of using HTL-free solar cells without deteriorating the efficiency. The solar cell is investigated by using SCAPS simulator.

In this paper, an analytical model of a proposed low-cost high efficiency NPN silicon-based solar cell structure is presented. The structure is based on using low cost heavily doped commercially available silicon wafers and proposed to be fabricated by the same steps as the conventional solar cells except an extra deep trench etch step. Moreover, the cell has been engineered to react to the UV spectrum, resulting in a greater conversion performance. The presented analytical model takes the electrical and optical characteristics into account. Thus, the influence of both physical and technological parameters on the structure performance could be easily examined. Consequently, the optimization of the structure performance becomes visible. To inspect the validity of the analytical model, a comparison of the main performance parameters resulting from the model results with TCAD simulations is carried out showing good agreement.

Enhancing the performance of photovoltaic (PV) systems has recently become a key concern because of the market demand for green energy. To obtain the most possible power from the solar module, it is imperative to allow the PV system to operate at its maximum power point (MPP) regardless of the climatic conditions. In this study, a comparison of distinctive Maximum Power-Point Tracking (MPPT) techniques is provided, which are Perturb and Observe (P&O) and Modified Variable Step-Size P&O, as well as Incremental Conductance (INC) and Modified Variable Step-Size INC, using a boost converter for two types of solar panels. Using MATLAB software, simulations have been performed to assess the efficiency of the solar module under several environmental conditions, standard test conditions (STCs), and sudden and ramp variations in both solar irradiance and temperature. The output power efficiency, time response, and steady-state power oscillations have all been taken into account in this study. The simulation results of the improved algorithms demonstrate an enhancement in the PV module performance over conventional algorithms in many factors including steady-state conditions, tracking time, and converter efficiency. Furthermore, a boost in the dynamic response in monitoring the MPP is observed in a variety of climatical circumstances. Moreover, the proposed P&O MPPT algorithm is implemented in a hardware system and the experimental results verified the effectiveness, regarding both fast-tracking speed and lower oscillations, of the proposed Variable Step-Size P&O algorithm and its superiority over the conventional P&O technique.

One of the most important challenges in the design of the piezoelectric energy harvester is its narrow bandwidth. Most of the input vibration sources are exposed to frequency variation during their operation. The piezoelectric energy harvester’s narrow bandwidth makes it difficult for the harvester to track the variations of the input vibration source frequency. Thus, the harvester’s output power and overall performance is expected to decline from the designed value. This current study aims to solve the problem of the piezoelectric energy harvester’s narrow bandwidth. The main objective is to achieve bandwidth broadening which is carried out by segmenting the piezoelectric material of the energy harvester into n segments; where n could be more than one. Three arrays with two, four, and six beams are shaped with two piezoelectric segments. The effect of changing the length of the piezoelectric material segment on the resonant frequency, output power, and bandwidth, as well as the frequency response is investigated. The proposed piezoelectric energy harvesters were implemented utilizing a finite element method (FEM) simulation in a MATLAB environment. The results show that increasing the number of array beams increases the output power and bandwidth. For the three-beam arrays, at n equals 2, 6 mW output power and a 9 Hz bandwidth were obtained. Moreover, the bandwidth of such arrays covered around 5% deviation from its resonant frequency. All structures were designed to operate as a steel wheel safety sensor which could be used in train tracks.