We report a micro light-emitting diode ( $\mu $ LED) pixel circuit using low-temperature poly-Si oxide (LTPO) thin film transistors (TFTs). The pixel circuit operates by pulse width modulation (PWM) to prevent the wavelength shift of $\mu $ LED. The proposed PWM can support 10-bit gray scale at a refresh rate of 120 Hz by PWM, thanks to the fast rise and fall times. Note that the circuit also compensates for the variation of the threshold voltage ( $\text{V}_{\text {TH}}{)}$ of the TFTs in the pixel. It is found that the current error rate is 3.7%, and the maximum pulse width error rate is 3.4% for low gray levels when the $\text{V}_{\text {TH}}$ shift is 0.5 V. The fabricated pixel circuit successfully demonstrates PWM of variable gray levels, with measured rise and fall times of $3~\mu \text{s}$ and $0.3~\mu \text{s}$ , respectively. Therefore, the proposed pixel circuit is suitable for $\mu $ LED display capable of expressing 10-bit gray scale at a refresh rate of 120 Hz.
We report high voltage amorphous indium gallium zinc oxide (a-IGZO) thin-film transistor (TFT) using a drain offset structure. The a-IGZO TFT with drain offset length ( $\text{L}_{ {\mathrm{off}}}$ ) = $2.5~ \boldsymbol {\mu }\text{m}$ exhibits a maximum operating voltage ( $\text{V}_{DS,Max}$ ) over 90 V, which increases with $\text{L}_{ {\mathrm{off}}}$ . The drastic current drop from output characteristics appears for ${\text{V}}_{DS} > \text{V}_{DS, Max}$ with a positive threshold voltage shift and increased subthreshold swing from transfer characteristics. We obtain maximum lattice temperatures of \sim 130 °C for both the conventional and drain offset TFTs due to Joule heating (JH) within the a-IGZO layer by TCAD simulation. It indicates that the rise in temperature by JH is almost independent of $\text{L}_{ {\mathrm{off}}}$ . The JH is uniformly distributed over the entire $\text{L}_{ {\mathrm{off}}}$ in drain offset TFT compared with a drastic increase near the drain side in conventional TFT. NF 3 plasma treatment enhances conductivity at offset region, resulting in large $\text{V}_{DS, Max}$ .
We report the performance improvement of low-temperature coplanar indium–gallium–zinc–oxide (IGZO) thin-film transistors (TFTs) with a maximum process temperature of 230 °C. We treated F plasma on the surface of an SiO2 buffer layer before depositing the IGZO semiconductor by reactive sputtering. The field-effect mobility increases from 3.8 to 9.0 cm2 V−1·s−1, and the threshold voltage shift (ΔVth) under positive-bias temperature stress decreases from 3.2 to 0.2 V by F-plasma exposure. High-resolution transmission electron microscopy and atom probe tomography analysis reveal that indium fluoride (In-F) nanoparticles are formed at the IGZO/buffer layer interface. This increases the density of the IGZO and improves the TFT performance as well as its bias stability. The results can be applied to the manufacturing of low-temperature coplanar oxide TFTs for oxide electronics, including information displays.
10 August 2023 in ACS Applied Materials & Interfaces
A piezoresistive sensor is an essential component of wearable electronics that can detect resistance changes when pressure is applied. In general, microstructures of sensing layers have been adopted as an effective approach to enhance piezoresistive performance. However, the mold-casted microstructures typically have quite a thick layer with dozens of microscales. In this paper, a carbon microstructure is formed by blue laser annealing (BLA) on a carbon nanotube (CNT) layer, which changes the surface morphology of CNTs into carbonaceous protrusions and increases its thickness more than four times compared to the as-deposited layer. Then, the pressure sensor is fabricated using a spin-coating of styrene–ethylene–butylene–styrene (SEBS) elastomer on the BLA CNTs layer. A 1.32 µm-thick pressure sensor exhibits a high sensitivity of 6.87 × 105 kPa−1, a wide sensing range of 278 Pa~40 kPa and a fast response/recovery time of 20 ms, respectively. The stability of the pressure sensor is demonstrated by the repeated loading and unloading of 20 kPa for 4000 cycles. The stretchable pressure sensor was also demonstrated using lateral CNT electrodes on SEBS surface, exhibiting stable pressure performance, with up to 20% stretching.