There are several techniques for the removal of pharmaceuticals (drugs) from wastewater; however, strengths and weaknesses have been observed in their elimination processes that limit their applicability. Therefore, we aimed to evaluate the best techniques for the removal of pharmaceuticals from municipal and hospital wastewater. For this, a non-experimental, descriptive, qualitative–quantitative design was used, corresponding to a systematic review without meta-analysis. Based on established inclusion and exclusion criteria, 31 open-access articles were selected from the Scopus, ProQuest, EBSCOhost, and ScienceDirect databases. The results showed that high concentrations of analgesics such as naproxen (1.37 mg/L) and antibiotics such as norfloxacin (0.561 mg/L) are frequently found in wastewater and that techniques such as reverse osmosis, ozonation, and activated sludge have the best removal efficiency, achieving values of 99%. It was concluded that reverse osmosis is one of the most efficient techniques for eliminating ofloxacin, sulfamethoxazole, carbamazepine, and diclofenac from municipal wastewater, with removal rates ranging from 96 to 99.9%, while for hospital wastewater the activated sludge technique proved to be efficient, eliminating analgesics and antibiotics in the range of 41–99%.

The enormous environmental problems that arise from organic waste have increased due to the significant population increase worldwide. Microbial fuel cells provide a novel solution for the use of waste as fuel for electricity generation. In this investigation, onion waste was used, and managed to generate maximum peaks of 4.459 ± 0.0608 mA and 0.991 ± 0.02 V of current and voltage, respectively. The conductivity values increased rapidly to 179,987 ± 2859 mS/cm, while the optimal pH in which the most significant current was generated was 6968 ± 0.286, and the ° Brix values decreased rapidly due to the degradation of organic matter. The microbial fuel cells showed a low internal resistance (154,389 ± 5228 Ω), with a power density of 595.69 ± 15.05 mW/cm² at a current density of 6.02 A/cm²; these values are higher than those reported by other authors in the literature. The diffractogram spectra of the onion debris from FTIR show a decrease in the most intense peaks, compared to the initial ones with the final ones. It was possible to identify the species Pseudomona eruginosa, Acinetobacter bereziniae, Stenotrophomonas maltophilia, and Yarrowia lipolytica adhered to the anode electrode at the end of the monitoring using the molecular technique.

Power generation and wastewater treatment are two great challenges for sustainable development. Microbial fuel cells (MFCs) are a sustainable alternative that can generate bioelectricity in the bioremediation process of wastewater. For this reason, the objective of this research was to generate bioelectricity through double-chamber microbial-combustion cell systems from wastewater from the Covicorti Wastewater Treatment Plant (PTARC) in the anodic chamber and electrogenic bacteria such as Stenotrophomonas maltophilia, Acinetobacter bereziniae, and Achromobacteria xylosoxidans in the cathode chamber, respectively. Measurements of the voltage, current, power density, current density, and optical density of the bacteria and biochemical oxygen demand (BOD) were made. In addition, a metagenomic analysis of the wastewater sample was performed. It was shown that the MFC with A. xylosoxidans generated the highest voltage peak (1.01 ± 0.06 V) on day 24, while the MFC with S. maltophilia generated the highest current value (0.71 ± 0.02 mA). The pH levels were slightly alkaline, and the maximum anodic conductivity value was presented by the MFC with A. cerevisiae, with a peak value of 81 ± 2 mS/cm on day 24. On the other hand, a maximum power density and current density of 195,493 ± 4717 mW/m² and 4987 A/cm², respectively, were obtained in the MFC with A. xylosoxidans. Finally, the metagenomic analysis identified the predominant phyla of Proteobacteria present in wastewater samples capable of generating electrical energy as Bacillota, Pseudomonadota, Bacteroidota, Actinomyketone, and Campylobacterota.

The large amounts of organic waste thrown into the garbage without any productivity, and the increase in the demand for electrical energy worldwide, has led to the search for new eco-friendly ways of generating electricity. Because of this, microbial fuel cells have begun to be used as a technology to generate bioelectricity. The main objective of this research was to generate bioelectricity through banana waste using a low-cost laboratory-scale method, achieving the generation of maximum currents and voltages of 3.71667 ± 0.05304 mA and 1.01 ± 0.017 V, with an optimal pH of 4.023 ± 0.064 and a maximum electrical conductivity of the substrate of 182.333 ± 3.51 µS/cm. The FTIR spectra of the initial and final substrate show a decrease in the peaks belonging to phenolic compounds, alkanes, and alkenes, mainly. The maximum power density was 5736.112 ± 12.62 mW/cm² at a current density of 6.501 A/cm² with a peak voltage of 1006.95 mV. The molecular analysis of the biofilm formed on the anode electrode identified the species Pseudomonas aeruginosa (100%), and Paenalcaligenes suwonensis (99.09%), Klebsiella oxytoca (99.39%) and Raoultella terrigena (99.8%), as the main electricity generators for this type of substrate. This research gives a second use to the fruit with benefits for farmers and companies dedicated to exporting and importing because they can reduce their expenses by using their own waste.

The accelerated increase in energy consumption by human activity has generated an increase in the search for new energies that do not pollute the environment, due to this, microbial fuel cells are shown as a promising technology. The objective of this research was to observe the influence on the generation of bioelectricity of sucrose, with different percentages (0%, 5%, 10% and 20%), in papaya waste using microbial fuel cells (MFCs). It was possible to generate voltage and current peaks of 0.955 V and 5.079 mA for the cell with 20% sucrose, which operated at an optimal pH of 4.98 on day fifteen. In the same way, the internal resistance values of all the cells were influenced by the increase in sucrose, showing that the cell without sucrose was 0.1952 ± 0.00214 KΩ and with 20% it was 0.044306 ± 0.0014 KΩ. The maximum power density was 583.09 mW/cm² at a current density of 407.13 A/cm² and with a peak voltage of 910.94 mV, while phenolic compounds are the ones with the greatest presence in the FTIR (Fourier transform infrared spectroscopy) absorbance spectrum. We were able to molecularly identify the species Achromobacter xylosoxidans (99.32%), Acinetobacter bereziniae (99.93%) and Stenotrophomonas maltophilia (100%) present in the anode electrode of the MFCs. This research gives a novel use for sucrose to increase the energy values in a microbial fuel cell, improving the existing ones and generating a novel way of generating electricity that is friendly to the environment.

The use of organic waste as fuel for energy generation will reduce the great environmental problems currently caused by the consumption of fossil sources, giving agribusiness companies a profitable way to use their waste. In this research, tomato waste with different percentages of sucrose (0-target, 5, 10, and 20%) was used in microbial fuel cells manufactured on a laboratory scale with zinc and copper electrodes, managing to generate maximum peaks of voltage and a current of 1.08 V and 6.67 mA in the cell with 20% sucrose, in which it was observed that the optimum operating pH was 5.29, while the MFC with 0% (target) sucrose generated 0.91 V and 3.12 A on day 13 with a similar pH, even though all the cells worked in an acidic pH. Likewise, the cell with 20% sucrose had the lowest internal resistance (0.148541 ± 0.012361 KΩ) and the highest power density (224.77 mW/cm²) at a current density of 4.43 mA/cm², while the MFC with 0% sucrose generated 160.52 mW/cm² and 4.38 mA/cm² of power density and current density, respectively, with an internal resistance of 0.34116 ± 0.2914 KΩ. In this sense, the FTIR (Fourier-transform infrared spectroscopy) of all the substrates used showed a high content of phenolic compounds and carboxylate acids. Finally, the MFCs were connected in a series and managed to generate a voltage of 3.43 V, enough to light an LED (green). These results give great hope to companies and society that, in the near future, this technology can be taken to a larger scale.