Regardless of the increasingly intensive application of vehicles with electric drives, internal combustion engines are still dominant as power units of mobile systems in various sectors of the economy. In order to reduce the emission of exhaust gases and satisfy legal regulations, as a temporary solution, hybrid drives with optimized internal combustion engines and their associated systems are increasingly being used. Application of the variable compression ratio and diesel fuel injection timing, as well as the tribological optimization of parts, contribute to the reduction in fuel consumption, partly due to the reduction in mechanical losses, which, according to test results, also results in the reduction in emissions. This manuscript presents the results of diesel engine testing on a test bench in laboratory conditions at different operating modes (compression ratio, fuel injection timing, engine speed, and load), which were processed using a zero-dimensional model of the combustion process. The test results should contribute to the optimization of the combustion process from the aspect of minimal particulate matter emission. As a special contribution, the results of tribological tests of materials for strengthening the sliding surface of the aluminum alloy piston and cylinder of the internal combustion engine and air compressors, which were obtained using a tribometer, are presented. In this way, tribological optimization should also contribute to the reduction in particulate matter emissions due to the reduction in fuel consumption, and thus emissions due to the reduction in friction, as well as the recorded reduction in the wear of materials that are in sliding contact. In this way, it contributes to the reduction in harmful gases in the air.

The demand for an improvement in the tribological properties of lubricants used in various industrial plants, the automotive industry, and other power transmissions has resulted in the development of a whole family of improved lubricants based on nanotechnology. Especially important are nanotube additives, which significantly improve the tribological properties of lubricants, primarily by reducing the friction coefficient and wear of the coupled elements but also by reducing the temperature load and increasing the stability of the oil film between the lubricated surfaces. The properties of nanotube-based additives were further improved using elements such as metal oxides and compounds based on titanium, molybdenum, aluminum, etc. This paper presents the results obtained in the field of research and application of nanocomposite lubricant additives. It also gives a partial comparative analysis of the research conducted in this field. The primary goal of this paper is to analyze the research results in the field of the application of nanotubes in lubricants and to indicate the importance of their application, such as improving the tribological properties of machines and reducing power losses. Furthermore, this paper shows the negative impact of nanoparticles on the environment and human health and the costs of applying some types of nanoparticles.

Multi-criteria decision making (MCDM) is a relatively new tool for decision makers who deal with numerous and often contradictory factors during their decision making process. This paper presents a procedure to choose the optimal municipal solid waste (MSW) management system for the area of the city of Kragujevac (Republic of Serbia) based on the MCDM method. Two methods of multiple attribute decision making, i.e. SAW (simple additive weighting method) and TOPSIS (technique for order preference by similarity to ideal solution), respectively, were used to compare the proposed waste management strategies (WMS). Each of the created strategies was simulated using the software package IWM2. Total values for eight chosen parameters were calculated for all the strategies. Contribution of each of the six waste treatment options was valorized. The SAW analysis was used to obtain the sum characteristics for all the waste management treatment strategies and they were ranked accordingly. The TOPSIS method was used to calculate the relative closeness factors to the ideal solution for all the alternatives. Then, the proposed strategies were ranked in form of tables and diagrams obtained based on both MCDM methods. As shown in this paper, the results were in good agreement, which additionally confirmed and facilitated the choice of the optimal MSW management strategy.

An optimisation model for small datasets was applied to thixocasted/compocasted composites and hybrid composites with hypereutectic Al-18Si base alloys. Composites were produced with the addition of Al₂O₃ (36 µm/25 nm) or SiC (40 µm) particles. Based on the design of experiment, tribological tests were performed on the tribometer with block-on-disc contact geometry for normal loads of 100 and 200 N, a sliding speed of 0.5 m/s, and a sliding distance of 1000 m. For the prediction of the tribological behaviour of composites, artificial neural networks (ANNs) were used. Three inputs were considered for ANN training: type of reinforcement (base alloy, Al₂O₃ and SiC), amount of Al₂O₃ nano-reinforcement (0 and 0.5 wt.%), and load (100 and 200 N). Various ANNs were applied, and the best ANN for wear rate (WR), with an overall regression coefficient of 0.99484, was a network with architecture 3-15-1 and a logsig (logarithmic sigmoid) transfer function. For coefficient of friction (CoF), the best ANN was the one with architecture 3-6-1 and a tansig (hyperbolic tangent sigmoid) transfer function and had an overall regression coefficient of 0.93096. To investigate the potential of ANN for the prediction of two outputs simultaneously, an ANN was trained, and the best results were from network 3-5-2 with a logsig transfer function and overall regression coefficient of 0.99776, but the predicted values for CoF in this case did not show good correlation with experimental results. After the selection of the best ANNs, the Taguchi grey multi-response optimisation of WR and CoF was performed for the same combination of factors as the ANNs. For optimal WR and CoF, the combination of factors was as follows: composite with 3 wt.% Al₂O₃ micro-reinforcement, 0.5 wt.% Al₂O₃ nano-reinforcement, and a load of 100 N. The results show that developed ANN, the Taguchi method, and the Taguchi grey method can, with high reliability, be used for the optimisation of wear rate and coefficient of friction of hypereutectic Al-Si composites. Microstructural investigations of worn surfaces were performed, and the wear mechanism for all tested materials was light abrasion and adhesion. The findings from this research can contribute to the future development of hypereutectic Al-Si composites.

Using vehicles and other mobile systems to transport passengers and goods, approximately 25% of Europe's greenhouse gases are generated. At the same time, many research papers, published by researchers and students, promote the use of electric vehicl...

Motor vehicles in transport, as one of the important sectors of the economy, emit a significant amount of carbon dioxide and other products in the form of exhaust gases, which are harmful to human health. The emission of exhaust gases from motor vehicles is limited by appropriate regulations in accordance with environmental goals, such as the Paris Climate Agreement. Reduced emissions and fuel (energy) consumption is mainly achieved by applying modern technologies for the production of internal combustion engines; transitioning to cleaner fuels, such as renewable natural gas or biomethane; and using alternative propulsion systems. Biomethane stored in a liquid state in on-board reservoirs has advantages in truck transport, ships, and air traffic. The reason for this is due to the higher concentration of energy per unit volume of the reservoirs and the lower storage pressure and thus higher safety compared to the high-pressure storage option (compressed biomethane). The presented research is related to a proposition regarding the design of drive systems of city buses using biomethane as fuel in cases when fuel is stored on-board the vehicle as gas in a compressed aggregate state. In this study, the results of a calculation method regarding the roof-supporting structure of an experimental bus with gas reservoirs under higher pressure are discussed as well. This study also presents the possibility of reducing harmful emissions if biomethane is used instead of conventional fuels as a transitional solution to electric-powered vehicles. For the sake of comparison, it is suggested that the engaged energy and the amount of produced carbon dioxide emissions within the drive systems of different fuels are calculated according to the recommendations of the standard EN16258:2012.