Along with deep scaling transistors and complex electronics information exchange networks, very-large-scale-integrated (VLSI) circuits require high performance and ultra-low power consumption. In order to meet the demand of data-abundant workloads and their energy efficiency, improving only the transistor performance would not be sufficient. Super high-speed microprocessors are useless if the capacity of the data lines is not increased accordingly. Meanwhile, traditional on-chip copper interconnects reach their physical limitation of resistivity and reliability and may no longer be able to keep pace with a processor’s data throughput. As one of the potential alternatives, carbon nanotubes (CNTs) have attracted important attention to become the future emerging on-chip interconnects with possible explorations of new development directions. In this paper, we focus on the electrical, thermal, and process compatibility issues of current on-chip interconnects. We review the advantages, recent developments, and dilemmas of CNT-based interconnects from the perspective of different interconnect lengths and through-silicon-via (TSV) applications.
17 February 2022 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
In this article, we propose a carbon nanotube (CNT) field-effect transistor (CNFET)-based static random access memory (SRAM) design at the 5-nm technology node that is optimized based on the tradeoff between performance, stability, and power efficiency. In addition to size optimization, physical model parameters including CNT density, CNT diameter, and CNFET flat band voltage are evaluated and optimized for CNFET SRAM performance improvement. Optimized CNFET SRAM is compared with state-of-the-art 7-nm FinFET SRAM cell based on Arizona State University [ASAP 7-nm FinFET predictive technology models (PTM)] library. We find that the read, write EDPs, and static power of the proposed CNFET SRAM cell are improved by 67.6%, 71.5%, and 43.6%, respectively, compared with the FinFET SRAM cell, with slightly better stability. CNT interconnects both inside and in-between CNFET SRAM cells are considered to compose an all-carbon-based SRAM (ACS) array which will be discussed in the Part II of this article. A 7-nm FinFET SRAM cell with copper interconnects is implemented and used for comparison.
With the continuous shrinkage of integrated circuit (IC) dimensions, traditional copper interconnect technology is gradually unable to meet the requirements for performance improvement. Carbon nanotubes have gained widespread attention and research as a potential alternative to copper, due to their excellent electrical and mechanical properties. Among various methods for producing carbon nanotubes, chemical vapor deposition (CVD) has the advantages of mild reaction conditions, low cost, and simple reaction operations, making it the most promising approach to achieve compatibility with integrated circuit manufacturing processes. Combined with through silicon via (TSV), direct application of CVD-grown carbon nanotubes in IC interconnects can be achieved. In this article, based on the above background, we focus on discussing some of the main challenges and developments in the application of CVD-grown carbon nanotubes in IC interconnects, including low-temperature CVD, metallicity enrichment, and contact resistance.
16 February 2024 in IEEE Journal of the Electron Devices Society
This paper reports a performance optimized operational amplifier (OPAMP) using transconductance enhancement topology based on the amorphous indium-galliumzinc-oxide (a-IGZO) thin-film transistors (TFTs). The performance of TFTs is enhanced by N2O plasma treatment that presents electrical characteristics suitable for accomplishing an OPAMP. The circuit consists of 19 TFTs with measured phase margin (PM) and unity-gain frequency (UGF) of 35.8∘ and 200 kHz, respectively. The DC power consumption (PDC) is 0.68 mW. Notably, it exhibits a high voltage gain (Av) of 32.67 dB and bandwidth (BW) of 15 kHz with 15 V DC supply voltage. Scarcely any work was reported with such a high gain while having a sufficient BW. The OPAMP demonstrates excellent performance among all a-IGZO literature and provides substantial support for the future development of TFT-based integrated circuits (ICs).
Direct conversion of X-ray irradiation using a semiconductor material is an emerging technology in medical diagnosis, material sciences and industrial non-destructive testing. The wide bandgap (WBG) semiconductors with excellent electronic/optical properties, high breakdown field, high stability, and high radiation resistance are appealing options for X-ray detection applications. This article presents a comprehensive review of the applications of inorganic WBG semiconductors for X-ray detection in the past several decades. Different architectures of direct X-ray detectors, which are based on varied wide-bandgap semiconductors including metal oxides (Ga 2 O 3 , Bi 2 O 3 , PbO, ZnO) and operate on different working principles, are introduced and discussed systematically. Finally, the possible challenges and opportunities in the future development of WBG semiconductors-based direct X-ray detectors are discussed.
Transdermal drug delivery (TDD) system based on piezoelectric micropumps is a novel route of drug delivery that is wearable and highly patient-compliant. The advantage of valveless micropumps, such as their simple structure, high reliability and low cost, have been investigated in comparison to valve-based micropumps. However, the flow pulsation and backflow effect of valveless pump can reduce the controllability and precision of the system. Here, a TDD wearable device integrated with a dual-pump parallel valveless piezoelectric micropump and hollow microneedle array is presented, which is fabricated by means of 3D printing technology. The simulation analysis and experimental results indicate that the dual-pump parallel micropump with asynchronous driving can achieve a full forward flow and reduces the influence of flow pulsation on the system’s stability, showing the excellent controllability and high precision of the device. The output flow rate and pressure of the micropump can be controlled by the driving signal, which are about 1.61 mL/min and 700 Pa with the sine driving signal of 40 V, 600 Hz. Through animal experiments, we demonstrate that the device can successfully deliver insulin to mice and control blood glucose. In conclusion, this TDD device which potentially provides low-cost and high-precision results than existing technologies, shows considerable promise in wearable drug delivery applications, especially in managing chronic diseases that require long-term treatment.